Sonoff ZB Bridge-P Manual

Product Introduction

The device weight is less than 1 kg. The installation height of less than 2m is recommended.

LED indicator status instruction

Features

This is a Zigbee Bridge that allows you to control a variety of Zigbee devices by transforming Wi-Fi into Zigbee. You can remotely turn on/off or schedule on/off connected Zigbee devices, or share it with your family to control them together.

Operating Instruction

1. Download "eWeLink"App
   
   
   
   
   

2. Power on
   
   Power the device through Micro USB cable. After powering on, the device will enter the Pairing Mode during the first use. The Wi-Fi LED indicator changes in a cycle of two short and one long flash and release.
   The device will exit the Pairing Mode if not paired within 3mins. If you want to enter this mode, please long press pairing button for about 5s until the Wi-Fi LED indicator changes in a cycle of two short and one long flash and release.
   

3. Add Zigbee Bridge
   
   Tap "+" and select "Add Device", then operate following the prompt on the App.

4. Add Zigbee sub-devices to Zigbee Bridge
   
   Make the sub-devices enter the pairing mode, tap "Add" icon on the Zigbee Bridge interface, then wait it to find the sub-devices and pair.
   ZB Bridge-P can connect 26 sub-devices directly, one router-device can expand to connect 20 sub-devices, one bridge can connect up to 128 sub-devices.

Compatible Pairing Mode

If you fail to enter Pairing Mode, please try "Compatible Pairing Mode " to pair.

Long press Pairing button for 5s until the Wi-Fi LED indicator changes in a cycle of two short flashes and one long flash and release. Long press Pairing button for 5s again until the Wi-Fi LED indicator flashes quickly. Then, the device enters Compatible Pairing Mode.

For Android system:
Tap "+" and select "Compatible Pairing Mode " on app, Please follow the app prompts.

For iOS system:

1. When the device is in the compatible mode, please record the device ID ITEAD-********** which can be found in the Wi-Fi list of the mobile phone.
2. Return to the eWeLink app, tap "+", select "Scan ", then tap "Manual Input" at the bottom of the screen. Enter the recorded device ID and tap "Next" to complete the addition.

Specifications

Model	ZB Bridge-P
Input	5V 1A
Wireless connections	Wi-Fi IEEE802.11 b/g/n 2.4GHz, Zigbee 3.0
App operating systems	Android & iOS
Working temperature	-10ºC~40ºC
Casing Material	PC V0
Product Size	62x62x20mm

Cancel the alarm sounds

ZB Bridge-P can be muted through following any method:

1. Press the gateway pairing button with a pin card.
2. Click the red "speaker" icon on the gateway interface of eWeLink App.
3. Mute the gateway through scene control settings.

Factory Reset

1. Delete Zigbee sub-devices
   
   Long press the pairing button for IOS until the Zigbee LED indicator "flashes twice", then all the paired Zigbee sub-devices have been deleted. If you want to delete one of the Zigbee sub-devices, delete it on the App.

2. Delete the Bridge Tap "Delete device" in the setting interface of the Bridge on the App, the device will be reset to factory setting.

Common Problems

Fail to pair Wi-Fi devices to eWeLink APP

1. Make sure the device is in pairing mode. After three minutes of unsuccessful pairing, the device will automatically exit pairing mode.
2. Please turn on location services and allow location permission. Before choosing the Wi-Fi network, location services should be turned on and location permission should be allowed. Location information permission is used to obtain Wi-Fi list information. If you click Disable, you will not be able to add devices.
3. Make sure your Wi-Fi network runs on the 2.4GHz band.
4. Make sure you entered a correct Wi-Fi SSID and password, no special characters contained. Wrong password is a very common reason for pairing failure.
5. The device shall get close to the router for a good transmission signal condition while pairing.

Wi-Fi devices "Offline" issue, Please check the following problems by the Wi-Fi LED indicator status:

The LED indicator blinks once every 2s means you fail to connect to the router.

1. Maybe you entered the wrong Wi-Fi SSID and password.
2. Make sure that your Wi-Fi SSID and password don't contain special characters, for example, the Hebrew, Arabic characters, our system can't recognize these characters and then fail to connect to the Wi-Fi.
3. Maybe your router has a lower carrying capacity.
4. Maybe the Wi-Fi strength is weak. Your router is too far away from your device, or there may be some obstacle between the router and device which blocks the signal transmission.
5. Be sure that the MAC of the device is not on the blacklist of your MAC management.

The LED indicator flashes twice on repeated means you fail to connect to the server.

1. Make sure the Internet connection is working. You can use your phone or PC to connect to the Internet, and if it fails to access, please check the availability of the Internet connection.
2. Maybe your router has a low carrying capacity. The number of devices connected to the router exceeds its maximum value. Please confirm the maximum number of devices that your router can carry. If it exceeds, please delete some devices or get a lager router and try again.
3. Please contact your ISP and confirm our server address is not shielded:
   eu-disp.coolkit.cc (in EU)
   us-disp.coolkit.cc (in US)

If none of the above methods solved this problem, please submit your request via help&feedback on the eWeLink APP.

Website: sonoff.tech

Service email: support@itead.cc

Documents / Resources

References

• App Store - Apple
• Google Play
• Welcome to OpenResty!
• Welcome to OpenResty!
• SONOFF Official Homepage| Smart Home automation SONOFF Official

Download manual

Here you can download full pdf version of manual, it may contain additional safety instructions, warranty information, FCC rules, etc.

Download Sonoff ZB Bridge-P Manual