Advertisement
Flood Sensor
User manual ver. 1.1
The document presents collected information on safety, assembly and use of Auraton Flood Sensor.
Basic information
Auraton Flood Sensor is designed to detect flooding in a controlled room/area. The device is intended
for cooperation with Auraton Flood Sensor Valve (shut-off valve). One Flood Sensor Valve (FSV) may
operate with up to 10 sensors.
ATTENTION:
The system will minimize the damage resulting from the flooding only when*:
Flood Sensor Valve is correctly installed in the water system by the installer,
Flood Sensor Valve (FSV) valve is correctly paired with at least one Flood Sensor (FS),
radio communication between FS and FSV is carried out correctly and reliably, which was
previously tested (devices should not operate close to their working range limits),
Flood Sensor is installed close to the point of water supply, e.g. washing machine,
dishwasher, kitchen sink and has a factual possibility of leak detection,
FSV is permanently powered from included AC adapter or the battery pack, which is
recharged regularly, to maintain continuity of its operation,
the valve minimizes the risk in the system connected to it and cannot prevent the damage
caused by water outside the system to which it is connected, e.g. damage resulting from
leaking roofs, windows or operation of external premises/systems (flooding by the
neighbouring apartment).
Advertisement
Table of Contents
Subscribe to Our Youtube Channel
Related Manuals for AURATON smart Flood Sensor
Summary of Contents for AURATON smart Flood Sensor
- Page 1 The document presents collected information on safety, assembly and use of Auraton Flood Sensor. Basic information Auraton Flood Sensor is designed to detect flooding in a controlled room/area. The device is intended for cooperation with Auraton Flood Sensor Valve (shut-off valve). One Flood Sensor Valve (FSV) may operate with up to 10 sensors.
-
Page 2: Description Of The Device
*The manufacturer shall not be responsible for loss or damage resulting from flooding and other unforeseen events. Description of the device 1 – Flood sensor 2 – Operation status signal lamp 3 – Function button 4 – The magnet used to enable the pairing function of Flood Sensor Valve (... -
Page 3: Installation
Installation Flood Sensor flooding be put on the floor as close to the water system (washing machine, dishwasher, etc.), to be able to send the signal to the valve in case of detecting water/moisture. The distance between Flood Sensor and Flood Sensor Valve must not be less than 1.5 m, to avoid problems during radio communication. - Page 4 Activation of the pairing function – Auraton Pulse Central Unit In Auraton Pulse, the pairing function is activated via Auraton Smart App. After it is enabled, press green ‘+’ button located on the centre of the screen. On the next screen, press the home icon marked as “Devices”.
-
Page 7: Restoring Factory Settings
(BEEP) will be activated Hold the button and wait until you hear two longer beeps, then release the button. At this point, the device should sound a continuous beep. When you hear it shortly press the button to confirm that you want to delete all user data from Auraton Flood Sensor. ATTENTION: Long beeps indicate positive execution of the function, whereas short beeps indicate an error in executing the function. - Page 8 Mode I (local): In this mode, the valve and the sensor may work independently without the need to use Auraton Pulse central unit. Just properly pair the sensor with the valve. You can add from up to 10 sensors to one valve.
- Page 9 flooding, create schedules and more. Particularly important is the ability to relate the valve closing action with specific flood sensors, in order to carry out the automatic closing of the valve by Auraton Pulse when flooding is detected. Then you can also receive remote notification about flooding.
-
Page 10: Technical Specifications
flooding and every 6 hours. Only in these cases, Flood Sensor can receive a command from Auraton Pulse, e.g. for firmware update. Flood Sensor is designed to work with Flood Sensor Valve and these devices may be paired in the application by using ‘If-Execute’ function, e.g. ‘If the flooding occured, set FloodValveLevel at 0% (i.e. -
Page 11: Disposal Of The Device
IP rating: IP67 Humidity: ≤85% non-condensing Checking the operational status: LED, sound signalling Power supply: CR2450 3V non-removable Compatible with Internet getaway: Pulse Auraton 865.500 MHz 867.200 MHz Radio frequency: 868.150 MHz 868.450 MHz 869.800 MHz Radio signal strength: 11 dBm Category of the radio receiver: in a typical house, with standard wall structures –...
Need help?
Do you have a question about the smart Flood Sensor and is the answer not in the manual?
Questions and answers