Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Subscribe to Our Youtube Channel
Related Manuals for MechMaxx BX42S
Summary of Contents for MechMaxx BX42S
- Page 1 WARRANTY Operator’s Manual www. mechmaxx.com...
-
Page 3: Table Of Contents
METRIC TORQUE SPECIFICATIONS MAINTENANCE SAFETY PARTS DIAGRAM OPERATING SAFETY PARTS LIST STORAGE SAFETY TRANSPORT SAFETY OPERATION SAFETY TO THE NEW OPERATOR OR OWNER MACHINE COMPONENTS OPERATION PRE-OPERATIONAL CHECKLIST MACHINE SET- UP TRIMMING THE PTO SHAFT www. mechmaxx.com TABLE OF CONTENTS... -
Page 4: Specifications
SPECIFICATIONS Model BX42S Tractor Power 18-45HP Max. Throughput Capacity 4 in Infeed Opening 4*10 in lnfeed Chute Opening 20*20 in Feeding Opening Gravity Feed Discharge Chute Rotation 360 Degrees Rotor Diameter 26 in Rotor Thickness 0.2 in Rotor Weight 82 lbs... -
Page 5: Safety Signs
Keep all guards in place when operating. • Operate only at 540 RPM. • Keep hands, feet, hair and clothing away from moving parts. • Keep U-joint angles equal and small as possible. • Do not exceed driveline manufacturers recommended operating length. www. mechmaxx.com SAFETY SIGNS... -
Page 6: Safety
. To avoid personal injury or Wear appropriate protective gear. This list includes but is death, study the following precautions and insist those not limited to: working with you, or for you to follow them. www. mechmaxx.com SAFETY... -
Page 7: Safety Training
. Safety signs are available from your authorized Distributor Pay close attention to the Safety Signs affixed to the skid or Dealer Parts Department or the factory. steer and the machine. www. mechmaxx.com SAFETY... -
Page 8: Preparation
Never work under equipment unless itis blocked securely. moving . Do not allow long hair, loose-fitting clothing, or jewelry to be around moving parts. www. mechmaxx.com SAFETY... -
Page 9: Storage Safety
. Inspect machine for damaged or loose parts before resuming work. www. mechmaxx.com SAFETY... -
Page 10: To The New Operator Or Owner
Do not exceed a safe travel speed when transporting. TO THE NEW OPERATOR OR OWNER The MechMaxx 3 Point Wood Chippers are designed to chip or chop scrap lumber, small trees, brush, limbs and other wood debris . The chipped material is fine enough to be composted or used in a variety of ways. -
Page 11: Machine Components
MACHINE COMPONENTS The MechMaxx 3 Point Wood Chipper is a rotor with blades for chipping wood . A hinged feed hopper moves the wood material into the rotor. Each rotor is designed with 2 blades and a twig-breaker to generate the small pieces of wood . A stationary knife at the rear of the rotor housing is placed by the moving knives to shear, chip or chop the material. -
Page 12: Operation
• Secure the feed hopper latch to the discharge chute PRE-OPERATIONAL CHECKLIST with the latch pin Efficient and safe operation of the MechMaxx 3 Point TRIMMING THE PTO SHAFT Wood Chipper requires that each operator reads and understands the using procedures and all related safety A PTO drive line is supplied with the machine. -
Page 13: Mounting And Unhooking Tractor
Use a hacksaw to cut dimension (C) from both ends. Cut both the plastic tubes and the metal cores. d. Use a file to remove the burrs from the edges that were cut. e. Assemble the 2 ends of the shaft. www. mechmaxx.com OPERATION... -
Page 14: Chipping Operation
• Pull the material out of the discharge hood. Use a stick to poke loose any material jammed into the discharge hood. Do not allow anything to remain in this area. • Check that everyone is clear of machine before restart- ing engine. www. mechmaxx.com OPERATION... -
Page 15: Severe Plug
• Close, install and fold down all components opened to unplug.Tighten fasteners to their specified torque. • Check that everyone is clear of machine before restart- ing engine. • Start the engine turn on the hydraulics and resume working. www. mechmaxx.com OPERATION... -
Page 16: Maintenance
6. Ensure the blade is properly oriented, with the leading edge out. The blade is designed to fit into the rotor one way only. See diagram for proper installation. 7. Tighten down bolts as specified in the torque chart. 8. Repeat steps for remaining blades. www. mechmaxx.com MAINTENANCE... -
Page 17: Ledger Blades
ENGLISH TORQUE SPECIFICATIONS LEDGER BLADES The MechMaxx-BX42S is equipped with a ledger (station- Bolt Torque ary) blade that acts as a shear for the moving rotor blades Bolt SAE 2 SAE 5 SAE 8 . The ledger blade is designed with 4 usable corners . -
Page 18: Parts Diagram
PARTS DIAGRAM www. mechmaxx.com PARTS DIAGRAM... -
Page 19: Parts List
Counter knife PTO cover Bolt M6*20 Nut M6 Bracket Bolt M14*1.5*45 Bearing UCFU208 with seat Fly wheel weldment Grease nipple Knife Rubber Plate Bolt M8*25 Nut M8 Hopper weldment Nut M10 Top cover weldment Lock pin 5 www. mechmaxx.com PARTS LIST... - Page 20 info@mechmaxx.com...
Need help?
Do you have a question about the BX42S and is the answer not in the manual?
Questions and answers