Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Subscribe to Our Youtube Channel
Related Manuals for MechMaxx BX62S
Summary of Contents for MechMaxx BX62S
- Page 1 WARRANTY Operator’s Manual www. mechmaxx.com...
-
Page 3: Table Of Contents
ROTOR BLADES MAINTENANCE PREPARATION LEDGER BLADES MAINTENANCE MAINTENANCE SAFETY BOLT TORQUEBOLT TORQUE TRANSPORT SAFETY ENGLISH TORQUE SPECIFICATIONS TO THE NEW OPERATOR OR OWNER METRIC TORQUE SPECIFICATIONS OPERATION PARTS DIAGRAM OPERATION PARTS LIST MACHINE COMPONENTS MACHINE BREAK-IN www. mechmaxx.com TABLE OF CONTENTS... -
Page 4: Specifications
SPECIFICATIONS Model BX62S Tractor Power 30-75HP Max. Throughput Capacity 6 in Infeed Opening 6.5*10 in lnfeed Chute Opening 25*25 in Feeding Opening Gravity Feed Discharge Chute Rotation 360 Degrees Rotor Diameter 30 in Rotor Thickness 0.2 in Rotor Weight 190 lbs... -
Page 5: Safety Signs
Keep all guards in place when operating. • Operate only at 540 RPM. • Keep hands, feet, hair and clothing away from moving parts. • Keep U-joint angles equal and small as possible. • Do not exceed driveline manufacturers recommended operating length. www. mechmaxx.com SAFETY SIGNS... -
Page 6: Your Safety
GENERAL SAFETY operator, can avoid many accidents by observing the following precautions in this section. To avoid personal injury or death, study the following precautions and insist those working with you, or for you to follow them. www. mechmaxx.com SAFETY... -
Page 7: Safety Training
4. Safety signs have a part number in the lower right hand corner. Use this part number when ordering replacement parts. 5. Safety signs are available from your authorized Distrib- utor or Dealer Parts Department or the factory. www. mechmaxx.com SAFETY... -
Page 8: Preparation
Untrained 3. Make sure there is plenty of ventilation. Never operate operators are not qualified to operate the machine. the engine of the towing vehicle in a closed building. The exhaust fumes may cause asphyxiation. www. mechmaxx.com SAFETY... - Page 9 By following the using instructions in conjunction with a good maintenance program, your tractor Wood Chipper will provide many years of trouble- free service. www. mechmaxx.com SAFETY...
-
Page 10: Operation
5. Lubricate all grease fittings. After operating for 10 hours: 1. Repeat steps 1 through 5 listed above. (After operating for 1 hour) 2. Go to the normal servicing and maintenance schedule as defined in the Maintenance Section. www. mechmaxx.com OPERATION... -
Page 11: Machine Set-Up
If the compressed drive line dimension exceeds the out, the bearings on both the machine and tractor PTO machine dimension, the drive line will have to be cut. shaft will be overloaded and fail in a short time. www. mechmaxx.com OPERATION... -
Page 12: Mounting And Unhooking Tractor
Be sure the telescoping portion of the shaft is greased and free of dirt. a. Slide the collar back on the yoke, align the splines and slide the yoke on the tractor. b. Release the collar and make sure the locking pin clicks into position. www. mechmaxx.com OPERATION... -
Page 13: Chipping Operation
Loosen the feed hopper anchor nuts and raise the feed hopper. d. Remove jammed material from inside the rotor compartment. www. mechmaxx.com OPERATION... - Page 14 Close, install and fold down all components opened to unplug. Tighten fasteners to their specified torque. i. Check that everyone is clear of machine before restart- ing engine. j. Start the engine turn on the hydraulics and resume working www. mechmaxx.com OPERATION...
-
Page 15: Maintenance
6. Ensure the blade is properly oriented, with the leading edge out. The blade is designed to fit into the rotor one way only. See diagram for proper installation. 7. Tighten down bolts as specified in the torque chart. 8. Repeat steps for remaining blades. www. mechmaxx.com MAINTENANCE... -
Page 16: Ledger Blades Maintenance
LEDGER BLADES MAINTENANCE BOLT TORQUE CHECKING BOLT TORQUE The bx62S is equipped with a ledger (stationary) blade that acts as a shear for the moving rotor blades. The The tables shown below give correct torque values for ledger blade is designed with 4 usable corners. When the various bolts and cap screws. -
Page 17: Metric Torque Specifications
METRIC TORQUE SPECIFICATIONS Bolt Torque Bolt 10.9 Diameter lb-ft lb-ft 1050 1495 1103 2100 1550 2600 1917 3675 2710 10.9 www. mechmaxx.com MAINTENANCE... -
Page 18: Parts Diagram
PARTS DIAGRAM www. mechmaxx.com PARTS DIAGRAM... -
Page 19: Parts List
WASHER 14 Bearing cover Bearing UCFU210 Rotor Weldment Plate Bolt M10*20 PTO Cover Housing, Bottom Rotor Knife, Ledger Nut M10 SPRING WASHER 10 WASHER 12 Ledger Knife bolt SPRING WASHER 12 Bolt M12*40 Bolt M12*30 Twig Breaker www. mechmaxx.com PARTS LIST... - Page 20 PARTS DIAGRAM PARTS LIST DESCRIPTION Knife, Rotor WASHER 12 SPRING WASHER 12 Bolt M10*20 Rotor Weldment www. mechmaxx.com PARTS DIAGRAM...
- Page 21 PARTS DIAGRAM PARTS LIST DESCRIPTION DESCRIPTION Deflector, Discharge Chute Lock nut M6 Knob 10*40 Washer 6 D shackle Hood Latch Tension spring 3 Bolt M6*25 Discharge Chute Plate, Spacer Ring Short chain Plate, Hood Capture www. mechmaxx.com PARTS DIAGRAM...
- Page 22 PARTS DIAGRAM PARTS LIST DESCRIPTION Infeed Hopper Flap, Hopper Strap, Hopper Flap WASHER 6 SPRING WASHER 6 Bolt M6*12 www. mechmaxx.com PARTS DIAGRAM...
- Page 24 info@mechmaxx.com...
Need help?
Do you have a question about the BX62S and is the answer not in the manual?
Questions and answers