Related Manuals for Omega OSXL-101
Summary of Contents for Omega OSXL-101
- Page 1 User’ s Guide Shop online at omega.com e-mail: info@omega.com For latest product manuals: omegamanual.info MADE IN JAPAN OSXL-101 Compact Thermal Image Sensor This datasheet has been downloaded from http://www.digchip.com at this page...
- Page 2 Approach Directives. OMEGA will add the CE mark to every appropriate device upon certification. The information contained in this document is believed to be correct, but OMEGA accepts no liability for any errors it contains, and reserves the right to alter specifications without notice.
-
Page 3: Before Using
Introduction Thank you for purchasing a compact thermal image sensor. In order to use this product safely, please read this instruction manual completely before use and confirm the correct handling and instructions. In addition, please retain this instruction manual for future reference. Before using Please confirm the contents of packing. - Page 4 About this instruction manual Under absolutely no circumstances may the contents of this instruction manual, in part or in whole, be transcribed or copied without permission. The contents in this instruction manual are subject to change without notice in future. ...
-
Page 5: Safety Precautions
Safety precautions The safety precautions shown in this manual indicate the important contents about safety. Please be sure to understand and follow these precautions. In this manual, in order to use this product safely, the precautions are described with the following indications and marks. -
Page 6: Precautions For Use
Precautions for use This product is a precision instrument. Do not drop it or make a strong impact on it. Do not use it in water. Keep this product away from equipments generating strong static electricity and electromagnetic waves including TVs, microwave ovens and wireless applications, or it may cause malfunction or trouble on this product. -
Page 7: Table Of Contents
Contents 【準備・設定編】 ■ Introduction ............I ■ Safety precautions ..........III ■ Precautions for use ..........IV ■ Outline of product 1. Configuration........... 1 2. Features ..........1 3. Functions ..........1 4. Model/specification........1 5. Basic configuration ……………………… 2 ■... -
Page 8: Outline Of Product
(e.g. PC or PLC). When the capture mode is used, a series of communication command is required. For the communication commands, contact to your nearest distributor. 4. Model/specification □□□ OSXL-101- View angle Blank: 60° (-20°C to 300°C) 25° (-20°C to 300°C) 25H: 25°... -
Page 9: Basic Configuration
5. Basic configuration 5-1. Connection with 1 Thermal Image Sensor to PC (Monitor mode) Monitor mode (when the supplied application software is used) The temperature data of entire thermopile array can be obtained from the PC. Supplied custom Network cable (Crossing cable) Thermal image sensor Alarm setup or monitor with... - Page 10 (DC12V 1.5A) 5-4. Connection to PLC (Capture mode) Capture mode ( when the supplied OMEGA application software is not used) The temperature data in a single row of the thermopile array can be obtained at a time by a command from a master unit (e.g. PC or PLC).
-
Page 11: Names And Functions
Names and functions (1) Monitor lamp (2) Lens Power/alarm output I/F connector connector (3) Mounting screw (6) Reset switch (Behind the screw) No Name Function The state of alarm and the condition of the sensor is indicated Monitor lamp with colors of blue, red and purple. (Refer to Page 8.) For forming image of radiation energy from a measurement Lens object on the detecting element... -
Page 12: Connection
Connection ● Connect the custom power/alarm output cable and the custom Network cable to this product. Connect them to align the marks of [] back of this product and [Arrow] on the cable connectors. To avoid misconnections, the custom Network cable is designed not to connect to the power/alarm output connector of this product. - Page 13 [Details of custom power/alarm output cable] O-tip terminal 0.5-3.7 Power + Black Power - Orange Alarm 1 + AL1 + Pink Alarm 1 - AL1 - Bright green Alarm 2 + AL2 + Blue Alarm 2 - AL2 - [Example of contact output circuit] Use the contact output with a protection device (e.g.
-
Page 14: Installation
: View per pixel For accurate measurements, 8 x 8 pixels or more for a target is recomended. 2.5m OSXL-101-25 and OSXL-101-25H <Relation between a measuring surface and a measuring distance> D (View width) = 0.5 × L (Measuring distance) 1.5m... -
Page 15: Operation
* Refer to Page 14 Troubleshooting. Operation mode 1. Monitor mode: When OMEGA application software is used The temperature data is sent continuously to a master unit (e.g. PC) by a command from the software.(The frame rate of the thermal image on the software is 3fps without any Alarm activated.) The alarm set on the sensor can provide a non-voltage contact output while sending the temperature data.(The frame rate goes down to 1fps or less with the alarm set on the sensor.) -
Page 16: Alarm Output
Alarm output 1. Specifications Item Specification Alarm area 1 area Alarm set value 2 values in a specified area Setting resolution 1 degree (°C/ºF) When consecutive 4 frames have satisfied the alarm Alarm activation condition condition When the measured temperature returns from the Alarm reset condition alarm set value in 4 images continuously Output Control... - Page 17 ● Alarm output and storing image Alarm state 警報状態 警報有 警報無 警報有 Contact output 警報出力 Auto Reset 自動復帰 画像上書き Image is overwritten. Image saving 画像保存 The image is saved only at the time 警報状態が連続で発生した場合は、発 of when alarming state turns from 生時の最初の画像を保存する...
-
Page 18: About Reset Switch
■ About reset switch In case of an error, etc. at the LAN environment settings, the set values can be reset to the default values as shipped from factory by removing the mounting screw and then pushing the reset switch. Turn the power on while pushing the reset switch for 1 second continuously. -
Page 19: Specifications
Center wavelength 10µm wavelength Measurement view angle 60° x 60° 25° x 25° Temperature -20°C to 300°C (OSXL-101-25) -20°C to 300°C measurement range 100°C to 800°C (OSXL-101-25H) Temperature resolution 0.5°C (at 100°C black body) ±2% of measured value or ±3°C, ±1% of measured value or ±3°C,... - Page 20 Replacement Power/Alarm Cable: OSXL-100-PAC Replacement Mounting Stand: OSXL-100-MOUNT Replacement Power Supply: OSXL-100-PS ■ Minimum requirements for the OMEGA application software Compatible PC: DOS/V computers with PC/AT compatible * The LAN port is required. * Display resolution: 800 x 600 pixels or more recommended * .NET Framework 2.0 or later has been installed and runs correctly.
-
Page 21: Precautions (For Maintaining Measurement Accuracy)
Precautions (For maintaining measurement accuracy) Pay attention to the followings for maintaining the measurement accuracy. Vibration and shock Vibration and shock causes not only a damage to the thermal image sensor in a long term but in stability of the measurement. When vibration is present, anti-vibration/shock absorber may be required between the thermal image sensor and a mounting plate or between the mounting bracket and a mounting plate. -
Page 22: External Dimensions
■External dimensions 1. Thermal image sensor (OSXL-101) 1. Thermal image sensor (OSXL-101-25, OSXL-101-25H) 2. Universal head When the thermal image sensor is installed with the universal head, mount the mounting bracket with 3 pieces of screws through the 3 holes on the bracket. If the universal head needs to be mounted on concrete surface, drill holes with 6.5mmø... - Page 23 Department will issue an Authorized Return (AR) number immediately upon phone or written request. Upon examination by OMEGA, if the unit is found to be defective, it will be repaired or replaced at no charge. OMEGA’s WARRANTY does not apply to defects resulting from any action of the purchaser, including but not limited to mishandling, improper interfacing, operation outside of design limits, improper repair, or unauthorized modification.
- Page 24 Where Do I Find Everything I Need for Process Measurement and Control? OMEGA…Of Course! Shop online at omega.com TEMPERATURE Thermocouple, RTD & Thermistor Probes, Connectors, Panels & Assemblies Wire: Thermocouple, RTD & Thermistor Calibrators & Ice Point References Recorders, Controllers & Process Monitors...
Need help?
Do you have a question about the OSXL-101 and is the answer not in the manual?
Questions and answers