Subscribe to Our Youtube Channel
Related Manuals for Promac 336BG
Summary of Contents for Promac 336BG
- Page 1 336BG Belt Grinder & Notcher Original: Operating Instructions Translations: Bedienungsanleitung Manuel d’Utilisation TOOL France S.A.S 9 Rue des Pyrénées, 91090 LISSES, France www.promac.fr. M/P–336BG 2024-01...
- Page 2 Déclaration de Conformité CE Product / Produkt / Produit: Belt Grinder & Notcher / Bandschleif- und Ausklinkmaschine / Ponceuse à bande/Grugeuse Model: 336BG Brand / Marke / Marque: PROMAC Manufacturer or authorized representative/ Hersteller oder Bevollmächtigter/ Fabricant ou son mandataire TOOL France S.A.S...
-
Page 3: Declaration Of Conformity
UK Declaration of Conformity Product: Belt Grinder & Notcher Model: 336BG Brand: PROMAC Manufacturer or authorized representative: TOOL France S.A.S Unit 1a Stepnell Park Off Lawford Road Rugby CV21 2UX United Kingdom We hereby declare that this product complies with the regulation:... -
Page 4: Table Of Contents
Dear Customer, Many thanks for the confidence you have shown in us with the purchase of your new PROMAC-machine. This manual has been prepared for the owner and operators of a PROMAC 336BG Belt Grinder & Notcher to promote safety during installation, operation and maintenance procedures. -
Page 5: Remaining Hazards
properly. Therefore the appropriate general technical rules carcinogenic substance. as well as the following notes must be observed. Always use a suitable dust extraction device Before machining, remove any nails and other foreign bodies from the workpiece. Read and understand the entire Never operate with the table insert not in place. -
Page 6: Noise Emission
Forward & Reverse 4.4 Description of machine Notching angle: 30°~90° Base size (footprint): 508x710mm This manual is provided by PROMAC, covering the safe Working height: 1100mm operation and maintenance procedures for the PROMAC Drive wheel size: Ø195mm 336BG series Belt Grinder. This manual contains Dust port diameter 2- Ø... -
Page 7: Mains Connection
Fig 2 It is recommended that Notcher be bolted to floor, using lag screws or similar means. See mounting pattern, Fig.3 Fig 4 Connect back dust collection outlet to dust extrusion system. Connect front dust collection outlet to proper container or bag. -
Page 8: Machine Operation
Fig 7 6.5 Removing/installing rollers 1. Disconnect machine from power source. Fig. 5 2. Remove tension from abrasive belt (J, Fig 7). 3.Loosen hex nuts (K, Fig.8) and turn set screws (L) to 6.3 Wheel grinding lower steel balls (M). 4.Slide out roller and insert new roller. -
Page 9: Maintenance And Adjustment
Keep notching table and guide shaft areas clean and free of debris. Use a brush to clear shavings, not bare hands. 7.2 Lubrication Note: Roller bearings are sealed and do not require further lubrication. See Fig 10 and Fig 11. 1.Apply oil or grease to tension leadscrew and contact points at hex nut. -
Page 10: Environmental Protection
Your appliance contains valuable materials which can be recovered or recycled. Please leave it at a specialized institution. This symbol indicates separate collection for electrical and electronic equipment required under the WEEE Directive (Directive 2012/19/EC) and is effective only within the European Union. 10. Available accessories Refer to the PROMAC-Price-list 11. Exploded View & Part List... - Page 11 336BG Belt Grinder & Notcher – Exploded View...
- Page 12 336BG Belt Grinder & Notcher – Parts List Index No. Part No. Description Size 1 ....DSAN4-1-1 ....Guide Seat ......................... 1 2 ....DSAN4-1-2 ....Sliding Plate ........................1 3 ....DSAN4-1-3 ....Short Guide Shaft ............ 6-5/8"L ..........2 4 ....
- Page 13 Index No. Part No. Description Size 60 ....TS-1504041....Socket HD Cap Screw ..........M8-1.25x20 ........2 61 ....TS-1504051....Socket HD Cap Screw ..........M8-1.25x25 ........2 62 ....TS-1505021....Socket HD Cap Screw ..........M10-1.5x20 ........3 63 ....DSAN4-1-63 ....Tracking Knob ............M10-1.5x50 ........1 64 ....
- Page 14 121 .... DSAN4T-121EU ..48mm Roller+BB-608ZZ w/2 shields (#121z) . . D48/d46.8/R2708 ......1 141 .... DSAN4T-145EU ..32mm Roller+BB-608ZZ w/2 shields (#141z) . . D32/d31 /R3250 ........ 1 ....PROMAC-160 ... PROMAC Logo (not shown) ........160x40 mm……………………… …..1 ............ ID Label, 336BG (not shown)........…………………………………………1 ....
- Page 15 Wiring Diagram for 336BG (400V 3PH)
Need help?
Do you have a question about the 336BG and is the answer not in the manual?
Questions and answers