1. Manuals
  2. Brands
  3. Emec Manuals
  4. Measuring Instruments
  5. LASP
  6. Operating manual

Emec LASP Operating Manual

Suction lances
Hide thumbs

Advertisement

Table of Contents

LASP4
Progettato da
Controllato da
Modificato da, il
Massimo_F
LASP
Data
02/04/2010
Materiale:
A4emec_verticale
LASP5
Progettato da
Controllato da
Modificato da, il
Massimo_F
SUCTION LANCES
Toll. Gen.
0.05
Edizione
Foglio
00
1
/
1
LASP6
Data
02/04/2010
Materiale:
A4emec_verticale
Toll. Gen.
0.05
Edizione
Foglio
1
/
1
00
EN

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the LASP and is the answer not in the manual?

Questions and answers

Related Manuals for Emec LASP

Summary of Contents for Emec LASP

  • Page 1 LASP LASP4 Progettato da Controllato da Modificato da, il Data Toll. Gen. Massimo_F  0.05 02/04/2010 Materiale: Edizione Foglio A4emec_verticale LASP5 LASP6 Progettato da Controllato da Modificato da, il Data Toll. Gen. Massimo_F 0.05  02/04/2010 Materiale: Edizione Foglio A4emec_verticale...
  • Page 2 This operating instructions contains safety information that if ignored can endanger life or result in serious injury. Read these instructions carefully before use and keep them for future reference. Information and specifications on this manual could be uncorrect or could have printing errors. Specifications are subject to change without notic .
  • Page 3 INTRODUCTION The suction lance is a device for the suction of chemical product from the storage tank. It is available in different sizes depending on the tank. FEATURES • Level probe for end product pre-alarm signal. lASP4 model is available with double level probe. •...

  • Page 4: Installation

    1. To install LASP on tank insert it in the through-hole and screw the counter nut. If the LASP is ordered together with the tank, the counter nut is not present: screw the LASP on the threading on tank after removing the collar nut.
  • Page 5 LASP4 nel tappo della tanica d) avvitare il collare sul raccordo e serrare il tutto 3. insert the LASP in the cap through-hole; 4. insert and screw the 1 1/2” counter nut; 5. screw the cap on the tank.
  • Page 6 2. Connect pump suction hoss to LASP output (1/2” fitting) Fig. 3. Hose assemby. hose holder holder ring tightening nut 3. Connect BNC level signal cable to BNC level on metering pump. If there are two level signal cable connect the second to an instrument or PLC.
  • Page 7 LASP4 G 1 1/2 34.00  SP4 per contenitori - 120 - 250 - 500 litri CNT SUITABLE o da, il Data Toll. Gen.  0.05 04/10/2011 62.80 Materiale: Edizione Foglio Assieme_lasp4_pd50 CNT PD50 (50 litri) CNT PD110 (110 litri) CNT PD200 (200 litri) CNT PD500 (500 litri) CNT PD1000 (1000 litri)
  • Page 8 DIMENSIONS Dimensions: mm LASP5 G 1 1/2 CNT SUITABLE P5 per contenitori 120 - 250 - 500 litri CNT PD50 (50 litri) Data Toll. a, il Gen. CNT PD110 (110 litri) 09/09/2011 0.05  Materiale: CNT PD200 (200 litri) Edizione Foglio Assieme_lasp5_pd50 CNT PD500 (500 litri)

  • Page 9: Maintenance

    Depressurize the system. The liquid may leak splashing. Drain the chemical from pump head and hoses. Unscrew LASP and pull it out of tank. LASP4: unscrew the bottom filter paying attention to the ceramic ball inside. Wash filter to remove deposit and crystals.

  • Page 10: Specifications

    LASP - Suction Lances Data Sheet LASP4-LASP5-LASP6 40CM X CNTPD50 LASP4-LASP5-LASP6 40CM X CNTPD50 LASP4-LASP5-LASP6 40CM X CNTPD50 FEATURES • Level switch (double level probes available) • Foot valve and foot filter • Adjustable height • 1 1/2” pipe fitting •...
  • Page 11 LASP - Suction Lances Data Sheet D IM E N S I O NS OPERATING LENGHT TANK VOLUME 40 cm 50 lt (mod. CNT PD 50) 63 cm 120 lt (mod. CNT PD 120) 75 cm 250 lt (mod. CNT PD 250) 108 cm 500 lt (mod.
  • Page 12 LASP - Suction Lances Data Sheet LASP4 tank version Via Donatori di sangue, 1 - 02100 Rieti - Italy Specifications subject to change without notice. ISO 9001:2015 Tel. +39 0746 2284 1 - Fax +39 0746 2284 2 - http://www.emecpumps.com...
  • Page 13 Disposal of end-of-life equipment by users This symbol warns you not to dispose of the product with normal waste. Respect human health and the environment by giving the discarded equipment to a designated collection center for the recycling of electronic and electrical equipment. For more information visit the online site.

This manual is also suitable for:

Lasp4Lasp5Lasp6

Table of Contents