GAUGEMASTER Infinity GMI-A31 Quick Start Manual

Hide thumbs Also See for Infinity GMI-A31:

Advertisement

Accessory Module Quick Start Guide

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the Infinity GMI-A31 and is the answer not in the manual?

Questions and answers

Subscribe to Our Youtube Channel

Summary of Contents for GAUGEMASTER Infinity GMI-A31

  • Page 1 Accessory Module Quick Start Guide...
  • Page 2 ∞ INTRODUCTION Thank you for purchasing this Gaugemaster Infinity Accessory Module. This guide takes you through all the necessary instructions for this unit, as well as the others in the range. Take care that the instructions for the correct module are being followed and to turn off the power to any module or controller before making any connections.
  • Page 3 This unit is designed to control lighting around the layout, however, it can also be used to control other accessories too*. This unit is fitted with two channels, allowing independent control of two electrical circuits. Power Input: Gaugemaster Infinity Solo or Duo Accessory Bus Connections: fig.1...
  • Page 4: Connecting Up The Module

    Connecting Up The Module. Please Note: When making any connections to this module please turn off your power supply to avoid damage to the module. This unit contains two outputs allowing independent control of two individual lighting circuits. Each output acts as a simple changeover switch so can be used in a number of ways to control lighting and other accessories around the layout.* See Page 3...
  • Page 5: Setting Up The Module

    Once the module is connected up as previously outlined, the Gaugemaster Infinity can be powered on. To begin setting up the module on your Gaugemaster Infinity system, an address is required to be assigned to each output. The factory default values of the channels are 1 and 2.
  • Page 6 Although designed for different systems, both the GMI-A32 and GMI-D31 connect and program in the same way. Power Inputs: GMI-A32 - Gaugemaster Infinity Solo or Duo Accessory Bus GMI-D31 - Gaugemaster Infinity Accessory Bus Connections: fig.3 Advanced Inputs †...
  • Page 7 Connecting Up The Module. Please Note: When making any connections to this module please turn off your power supply to avoid damage to the module. This unit contains four outputs, each designed to be connected to a solenoid point motor. Every solenoid motor has two coils that are usually referred to a ‘Coil A’...
  • Page 8 To Sequentially Set The Outputs: Firstly, the accessories need to be set up on the Gaugemaster Infinity Handset. ∞ Select the [MENU] key followed by [3] for Gaugemaster Infinity Sovereign users or [4] for Gaugemaster Infinity Solo or Duo users to access the additional features, then [2] to edit an accessory.
  • Page 9 For example; if the primary address is set to 5, the subsequent outputs will automatically be set to 6, 7, and 8. To Individually Set The Outputs: Firstly, the accessories need to be set up on the Gaugemaster Infinity Handset. ∞...
  • Page 10 This unit is designed to control 2, 3 or 4 aspect LED colour light signalling around the layout. When using a 2 aspect signal, this unit can also control an additional route indicator or theatre signal. Power Input: Gaugemaster Infinity Solo or Duo Accessory Bus Connections: fig.5...
  • Page 11 Please Note: When making any connections to this module please turn off your power supply to avoid damage to the module. fig.6 fig.7 LEARN LEARN BUTTON BUTTON Accessory Bus +/- Accessory Bus +/- Accessory Bus -/+ Accessory Bus -/+ ‡ Note: The diagram illustrates connection for 3 and 4 aspect signals, these can be connected separately, both are not required.
  • Page 12 Addresses will need to be assigned to both these - follow the steps below to get up and running. To Program The Outputs: Firstly, the accessories need to be set up on the Gaugemaster Infinity Handset. ∞...
  • Page 13: Controlling The Module

    If you have issues with the signal controller not performing as expected: ∞ Check that one of the signal LEDs is lit - if not check the connections between your module, the Gaugemaster Infinity Accessory Bus and the signals themselves. ∞...
  • Page 14 Reverse loop. If this is not possible, you can run these cables back to connect directly to your Gaugemaster Infinity Base Unit output. The “OUT” terminals connect to the isolated section of the reverse loop.
  • Page 15 Notes. Use this section to keep any notes you require related to these modules.
  • Page 16 This product is not a toy and contains small parts which may harm or choke a child. Not recommended for children under 14 years old unless supervised by an adult. Gaugemaster House, Ford Road, Arundel, West Sussex, BN18 0BN, United Kingdom...

Table of Contents