Advertisement

Quick Links

Feltest SpeedController
TrueSpeed
AirSpeed
Sensor
Sensor
User Manual
Version: 2022/2

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the SpeedController and is the answer not in the manual?

Questions and answers

Summary of Contents for Feltest SpeedController

  • Page 1 Feltest SpeedController TrueSpeed AirSpeed Sensor Sensor User Manual Version: 2022/2...
  • Page 2 SPEEDCONTROLLER 1. Power button 2. Charging and power LED 3. 4.3” Touchscreen 4. Sensor connector 5. Power over Ethernet (PoE+) charging and ethernet connector 6. Rubber cover for connector 7. Popsocket™ to hold the device 8. Back cover 9. Screw (4x) with rubber O-ring to hold the back cover 10.
  • Page 3: Table Of Contents

    10.3. Support ......16 CONTENTS 11. Specifications ......17 1. Introduction ......3 SpeedController ......17 2. Safety ........3 AirSpeed Sensor ......17 2.1. Safety Warnings ....3 TrueSpeed Sensor ..... 17 2.2. Safety instructions ....4 12. CE Declaration ......18 2.3.
  • Page 4: Introduction

    INTRODUCTION surroundings when using the measuring Congratulations on your purchase of instruments. the Feltest SpeedController and one or Do not measure felts or fabrics with both of the accompanying sensors: the holes or damaged edges! You could be Feltest AirSpeed Sensor and the pulled into moving machine parts or rip TrueSpeed Sensor.
  • Page 5: Safety Instructions

    Figure 1: SpeedController Use only replacement batteries that are authorized by Feltest. SPEEDCONTROLLER The batteries of the SpeedController The SpeedController set contains: heat up when charging. Charge at room temperature only, away from any heat 1. SpeedController device sources.
  • Page 6: Connecting To A Pc

    RJ45 ethernet connector is 3. Lightweight carbon telescopic rod supplied with the device. POWER OVER ETHERNET The SpeedController is a PoE+ (Power over Ethernet plus) device. This a LAN network that provides both data communication and electrical power to its connected devices.
  • Page 7: Making Contact

    This also applies Charge switch on demand. when using a RJ45 to USB adapter, because DHCP will not work. 2. The SpeedController receives an IP address from your network’s DHCP server, which is found on the device under Settings Network.
  • Page 8: Charging Batteries

    4.2. CHARGING BATTERIES Unit settings: The SpeedController has a charging and power LED (see #2 on the inside cover o AirSpeed Sensor of this manual). This LED indicates the m/s (meters per second) ...
  • Page 9: Database Set Up

    ADDING A PAPER MACHINE Network settings: Before using the SpeedController the first time, there must be at least one o IP Configuration Measuring location in the database. DHCP  Manual  First, connect the device to a network o IP address...
  • Page 10 MEASUREMENT TYPES The SpeedController offers two types of measurements for both the AirSpeed and the TrueSpeed Sensor: Figure 10 1. AirSpeed, point measurement 3. Add the paper machine clothing...
  • Page 11: Airspeed Sensor

    Never measure slit and the force with which the close to ingoing measuring head is pressed onto the felt. nips! The SpeedController automatically stores the highest value. Figure 13 Make sure the cable cannot be pulled into the paper machine.
  • Page 12: Truespeed Sensor

    Go to the Knowledge section of the amount of removed water. Feltest website for useful technical articles whitepapers on felt Still, only measuring the air speed is not permeability and the assessment of enough to determine the felt’s press felts.
  • Page 13: Securing The Handgrip

    2. Push the other connector of the black cable into the sensor As the surface of this wheel is quite receptable of SpeedController. The rough, it is advised to use this wheel SpeedController will automatically only outside the paper sheet’s run.
  • Page 14: Estimating Length

    9. Start a measurement on the 7. If you measured the speed in /min, SpeedController. divide your speed value by 60 to get 10. The SpeedController automatically the speed in m/s or ft/s. stores the highest value. 8. Multiply your speed/second with revolution time in seconds and you 8.4.
  • Page 15: Exporting Data

    9. EXPORTING DATA Figure 18 All measurements are stored in the How to mount a wheel memory of the SpeedController. The 1. Make sure the wheel is positioned measurements can be exported in the correctly; the axle (12) must be Export tab of the web interface.
  • Page 16: Maintenance

    Please contact support@feltest.com price and lead time of the AirSpeed snap head. Check the display of the SpeedController when connecting the sensor to see which version you have: The 20 m/s variant has article code • 200099 •...
  • Page 17: Cleaning The Vane

    3. Re-attach the white measuring head When you hear a click and the parts are (see chapter 10.1 step 5). nicely connected, check with a test measurement if the SpeedController 10.3. SUPPORT receives a signal from the sensor. For support please contact Step 5: Carefully reposition the white support@feltest.com...
  • Page 18: Specifications

    We offer maintenance and repair AIRSPEED SENSOR services. Please complete the repair Required Feltest service request form on our website control unit SpeedController prior to shipping your instrument to us: Measuring Count the pulses www.feltest.com/en/repair-request principle from the mini vane blades 11.
  • Page 19: Ce Declaration

    EU declaration of conformity: A. CONNECTING WITHOUT DHCP If the network does not support DHCP, or if you are using a RJ45 to USB adapter to connect the SpeedController Product: Feltest SpeedController to your laptop, the network settings for Type:...
  • Page 20 Keep this window open while going to your USB adapter or your network. the next step. Step 7 Disable DHCP on the SpeedController. To do this, go to “Settings”  “Network” and click “Disable DHCP”. Figure 31 Right-click and click “Status”.
  • Page 21: From .Csv To .Xlsx

    – as seen on your PC (see Step 6). The last value, after the 3 dot, that you enter in the SpeedController must be different from the value on your PC. Figure 36 An example: if your PC shows FROM .CSV TO .XLSX...
  • Page 22 Select column A, and click ‘Text to Columns’, a wizard pops up. Figure 38 3. Select the ‘Delimited’ option in the ‘Original data type’. Click next. 4. Select the ‘Comma’ as the Delimiter and click next. 5. First, select the column with ‘start’ as a header.
  • Page 23 C. TRUESPEED WET SLIP DIAGRAM...
  • Page 24 Feltest Equipment BV PO Box 205 6960 AE Eerbeek The Netherlands T: +31 313 652215 support@feltest.com www.feltest.com...

This manual is also suitable for:

AirspeedTruespeed

Table of Contents