Subscribe to Our Youtube Channel
Related Manuals for LANSEN LAN-WMBUS-GW5-M-LR-A1 CATM1 Series
Summary of Contents for LANSEN LAN-WMBUS-GW5-M-LR-A1 CATM1 Series
- Page 1 Q U I C K I N S T A L L A T I O N G U I D E OUTDOOR LONG-RANGE MAINS GATEWAY WITH OPTIONAL USE FOR ONE OR TWO EXTERNAL ANTENNAS LAN-WMBUS-GW5-M-LR-A1/A2-(X)-CATM1-(X) LAN-WMBUS-GW5-M-LR-A1/A2-(X)-CAT1/4G-(X) Version 1 Draft C...
- Page 2 Article Name Description LAN-WMBUS-D2-TC Lansen Configuration Warning, risk for bodily harm if handled Dongle without care. Lansen Configurator Software for Lansen Dongle LAN-CF-CABLE Configuration Cable, NOTICE: LAN-A-PMB-KIT- Pole mounting kit ID58-78 LAN-MAG-R4 Magnet with We are not responsible for any damage,...
-
Page 3: Label Information
868,600 B14/ B18/B19/B20/B2/ possible. B18/B19/B20/ B26/B28/B66/ B25/B26/B27/ N: 868,700 B28/B66/B85 For more information, go to our website at www.lansen.io. MHz to LTE-TDD 869,200 B34/B38/B39/ B40/ LABEL INFORMATION The label on the device gives useful information about your device, Output < 14 dBm /... -
Page 4: Installing And Mounting
Installing and mounting Step 2: Note: Do not use the hole on the back for outdoor usage! Step 1: The power supply cable can be mounted either through the cable Unscrew the screw (red circle) and remove the cover by guide at the bottom or through the hole on the back. - Page 5 Step 3: Step 5: Note: This solution gives IP-class 40. Do NOT use this for Thread the power supply cable (prepared in Step 4) outdoor installations! through the cable inlet, either from the back of the gateway or on the side (marked by red circles). Connect the power To use the hole in the back for a power supply cable, supply cable to the coupling clamps on the inside (marked carefully cut, drill or punch out the hole marked in the...
- Page 6 This might cause it to not get picked up by the SIM-card holder. Step 10: Install the Lansen pole mounting kit (article number LAN- 910-0066) on the back of the gateway. Pull the straps Step 8: through the holes and wrap it around the pole or pipe which...
-
Page 7: Step 11: Startup Sequence
We Connect the power. A beep will be heard and all 4 LEDs on recommend connecting to the device using a Lansen USB- Lansen the strip will light up. 1-2 minutes after the first beep you will... - Page 8 Step 13: Indications LED Strip (red circle) POWER Green Steady on The device A gateway has two places with LEDs One LED strip for has power. status of the device (red circle) and one LED for status of POWER Green All steady on Startup cellular connectivity (red arrow).
- Page 9 (868 MHz). in the middle). Note: Make sure to enable the parameter to use external antenna for wM-Bus by using Lansen Configurator or sending a command using MQTT. Note: Use the RIGHT SMA connection for wM-Bus.
- Page 10 Note: Make sure to enable the parameter to use external as far apart as possible (AT LEAST 50 CM) to avoid antenna for cellular network by using Lansen Configurator interference, either by using 2 antenna cables or attaching 1 or sending a command using MQTT.
Need help?
Do you have a question about the LAN-WMBUS-GW5-M-LR-A1 CATM1 Series and is the answer not in the manual?
Questions and answers