1. Manuals
  2. Brands
  3. Anderson Manuals
  4. Measuring Instruments
  5. HMP
  6. Instruction manual

Anderson HMP Instruction Manual

Turbine flowmeter
Hide thumbs
Table of Contents

Advertisement

Quick Links

Download this manual
Instruction Manual
HMP TURBINE FLOWMETER
Instrument Model Number _____________________________
Instrument Serial Number _________________________________
Anderson Instrument Co. Inc.
156 Auriesville Road
Fultonville, NY 12072
1-800-833-0081
Fax 518-922-8997
www.andinst.com
Form Number AIC2056 © 1/07
Effective: March 2007
Supercedes: NEW

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the HMP and is the answer not in the manual?

Questions and answers

Related Manuals for Anderson HMP

Summary of Contents for Anderson HMP

  • Page 1 Instruction Manual Anderson Instrument Co. Inc. 156 Auriesville Road Fultonville, NY 12072 1-800-833-0081 Fax 518-922-8997 www.andinst.com Instrument Model Number _____________________________ Instrument Serial Number _________________________________ HMP TURBINE FLOWMETER Form Number AIC2056 © 1/07 Effective: March 2007 Supercedes: NEW...

  • Page 2: Table Of Contents

    Table of Contents Section 1 - Specifications 1.1 Environmental Specifications 1.2 Operational Specifications Section 2 - Introduction 2.1 Description Section 3 - Installation 3.1 Location 3.2 Installation Illustration Section 4 - Electrical Wiring 4.1 Signal Probe Wiring 4.2 Wiring Diagram Section 5 - Calibration 5.1 K-Factor Section 6 - Maintenance...

  • Page 3: Section 1 - Specifications

    Section 1 - Specifications 1.1 ENVIRONMENTAL SPECIFICATIONS POWER / SIGNAL HTS1000 Supply Voltage: 8-24 VDC, 0.8 Watts maximum Signal Output: 7.3-23.3 VDC, Unscaled, Pulsed Output Output Units: Pulses Per Volume Ambient Temperature Range: -40° - 79°C (-40 - 175°F) HT75000 Supply Voltage: None Signal Output:...
  • Page 4 FIGURE 1.2 TURBINE DIMENSIONS “B” MODEL DIM “A” DIM “B” FITTING HMP075 3.25” (82.6mm) 5.88” (149.4mm) 1” T.C. HMP100 HMP150 3.63” (92.2mm) 6.13” (155.7mm) 1 1/2” T.C. HMP200 3.88” (98.6mm) 8.63” (219.2mm) 2” T.C. CONNECTION TO EXTENSION CABLE PICK-UP PROBE 3/4”...

  • Page 5: Section 2 - Introduction

    2.1 DESCRIPTION The HMP is a volumetric turbine flowmeter. As liquid flows through the meter, it causes the rotor to spin. An external non-contact pick-up probe counts each passing vane of the rotor as it spins. Each revolution of the rotor equates to an exact volume of liquid.

  • Page 6: Section 4 - Wiring

    NOTE: If it becomes necessary to splice cable connections, be sure to properly solder or join wire connections. Loose connections have the ability to generate false counts. DIAGRAM 4.2 WIRING DIAGRAM HMP SERIES TURBINE FLOWMETER ANDERSON INSTRUMENT CO., INC. PART NUMBER HT750000 HT750000 LENGTH - APPROX. 12'' WHEN THREADED INTO HM SERIES FLOWMETER FEMALE SOCKET (1)

  • Page 7: Section 5 - Calibration

    This identifies the amount of pulses the meter will output per a fixed volume that passes through it. In the case of Anderson flow products a gallon is the volume. This value is labeled on the meter body as a “P/G” pulses per gallon, which is also know as a “K-Factor”.

  • Page 8: Section 6 - Maintenance

    Section 6 - Maintenance The HMP flowmeter, if properly applied, should provide many years of trouble-free service. Excessive flow rates and/or temperature and pressure are conditions which most commonly cause damage to the flowmeter. 6.1 DISASSEMBLY AND INSPECTION Verify that all line pressure is relieved with all valves closed prior to removal of the meter. Disconnect signal cable and completely remove meter body from the product line.

  • Page 9: Assembly

    6.3 ASSEMBLY Verify the rotor spins freely on the shaft prior to installation. Rotate parts until they fall into place. Match assembly pieces with the orientation shown. (Figure 6.2) DO NOT FORCE THE PIECES TOGETHER! Be sure the gasket between the meter housings is in the groove of the body connection area. Secure the housing clamp and reinstall in the process line.

  • Page 10: Section 7 - Troubleshooting

    Section 7 - Troubleshooting HM FLOWMETER TROUBLESHOOTING GUIDE PROBLEM CAUSE ACTION • Failed Probe (no output) • Replace Probe • Probe not seated • Check probe: must be threaded to bottom • Moisture and/or corrosion • Disconnect extension cable at probe for in probe-to extension visual check, dry or clean if required cable connector...

  • Page 11: Section 8 - Warranty And Return Statement

    These products are warranted to be free from functional defects in materials and workmanship at the time the products leave the Anderson factory and to conform at that time to the specifications set forth in the relevant Anderson instruction manual or manuals, sheet or sheets, for such products for a period of one year.
  • Page 12 ANDERSON INSTRUMENT CO. LP • 400 BRITANNIA RD. EAST, UNIT 1 • MISSISSAUGA, ONTARIO L4Z 1X9 • CANADA • 905-568-1440 • FAX 905-568-1652 NEGELE MESSTECHNIK GmbH (A Division of Anderson) • RAIFFEISENWEG 7 • D-87743 EGG A. D. GÜNZ • GERMANY • +49 (0) 8333/9204-0 • FAX +49 (0) 8333/9204-49 MAIDA INTERNATIONAL (LATIN AMERICA &...

This manual is also suitable for:

Hmp075Hmp100Hmp150Hmp200

Table of Contents