Belkin F5C791-C6 Manual

Thank you for choosing the Belkin Notebook Travel Surge Protector (the Travel Surge Protector) for your mobile computer power protection needs. Your Notebook
Travel Surge Protector safeguards your laptop from power imbalances as you travel, in both domestic and international venues. Please read the general instructions
and safety information provided below for both Notebook Travel Surge Protector models: F5C791-C6 and F5C791-C8. File in a safe place for future reference.
Over-Current Detection Test (Fig. A)
1. Pull one end from the retractable 7 ft. phone cable and plug it into the telephone wall jack. Take the other end and plug it into the Travel Surge Protector jack
marked with the icon.
2. Depress the test button. If red indicator light turns on, an over-current exists and may damage your modem device or cause a malfunction. IMPORTANT: IF THE
RED LIGHT IS ON, DO NOT PLUG EQUIPMENT INTO THIS JACK. Seek a different phone jack or retest the same jack at a later time. If the red light remains off,
the line is OK and ready for safe use.
AC Line Installation (Fig. B)
Please verify that your laptop and telephone line are functioning properly before you install the Travel Surge Protector. It easily connects in-line between the laptop
power adapter and the adapter power cord.
1. Unplug the power cord from the power adapter.
2. Plug power adapter cord into the female end of the Travel Surge Protector.
3. Plug the male end of the Travel Surge Protector cord into the power adapter.
Telephone/Modem Installation (Fig. C)
1. Plug one end of the phone cable into the telephone wall jack and the other end into the Travel Surge Protector jack marked with the icon.
2. Plug the cord from the telephone into the Travel Surge Protector jack marked with the icon.
3. Pull one end from the retractable 7 ft. phone cable and plug into the Travel Surge Protector jack marked with the
your laptop.
The "Protected" light should be illuminated during use. If this light goes out at any time while in use, your Travel Surge Protector has sacrificed itself to protect your
equipment and should be replaced. Please contact Belkin Corporation for a free replacement Travel Surge Protector.

Safety Information

This unit is designed for use in countries with 100VAC–240VAC electrical utilities. Use in some countries may require a plug adapter.
Not for use with telephone ISDN or digital telephone lines.
Prior to installing unit, turn off and unplug all intended protected equipment.
For use in dry environments only. For absolute protection, do not use ELECTRIC equipment during an electrical storm.
Plug Type
C6 Connector
UL Suppressed Voltage Rating LN
Surge Entry Capacity @ 8/20uS
Phone Protection
Peak Surge Current @ 8/20uS
Telephone Breakover Voltage
Over-Current Detection Indicator
Phone Cable
Agency Approvals
Warranty
Connected Warranty
*C6 Connector 3-Prong, C8 Connector 2-Prong
1. Plug phone cord into
wall jack.
2. Depress test
button indicator
to test.
Figure A

Notebook Travel Surge Protector

Specifications

3. Plug the Travel Surge
test test
1. Unplug the power cord
from the power adapter.
Figure B
icon and plug the other end into
C6 Connector or C8 Connector*
100VAC—240VAC AC 50/60Hz
<800 Volts at 220VAC—240VAC
238 Joules at 220VAC—240VAC
Solid State Phone Protection
6500 Amps
275VAC
Yes
Includes 7' Retractable RJ11 Cable
UL, cUL and FCC
Lifetime Product Warranty
$75,000 Life
1. Plug the phone cord into the
Protector's cord into the
wall jack.
power adapter.
2. Plug power
cord into
the male
2. Plug the telephone cord into
end of the
the Travel Surge Protector.
Travel Surge
Protector.
3. Plug the computer
modem cable into
the Travel Surge
Protector.
Figure C