Download Print this page

Leap DOMINATOR LP Installation Manual

Aluminum light pole

Advertisement

Quick Links

INSTALLATION GUIDE
SECTION 1:
Safety Instructions
SECTION 2:
Light Pole Specifications
SECTION 3:
Bolt Plate Installation
SECTION 4:
Hoop Installation
SECTION 5:
Warranties & Policies
ALUMINUM LIGHT POLE
MODEL #: LP

Advertisement

loading
Need help?

Need help?

Do you have a question about the DOMINATOR LP and is the answer not in the manual?

Questions and answers

Subscribe to Our Youtube Channel

Summary of Contents for Leap DOMINATOR LP

  • Page 1 INSTALLATION GUIDE ALUMINUM LIGHT POLE MODEL #: LP SECTION 1: Safety Instructions SECTION 2: Light Pole Specifications SECTION 3: Bolt Plate Installation SECTION 4: Hoop Installation SECTION 5: Warranties & Policies...
  • Page 2: Safety Instructions

    SECTION 1: SAFETY INSTRUCTIONS SAFETY INSTRUCTIONS FAILURE TO FOLLOW THESE SAFETY INSTRUCTIONS MAY RESULT IN SERIOUS INJURY OR PROPERTY DAMAGE AND WILL VOID WARRANTY. Owner must ensure that all players know and follow these rules for safe operation of the system. To ensure safety, do not attempt to assemble this system without following the instructions carefully.
  • Page 3 SECTION 2: LIGHT POLE SPECIFICATIONS LIGHT POLE POLE HEIGHT (A) 12’ or 16’ POLE WIDTH (B) 4” x 4” HANDHOLE HEIGHT (C) 36” POLE MATERIAL 6061 T6 ALUMINUM POLE THICKNESS GAUGE 0.187” CROSSBAR WIDTH (D) (E) 30” (2 FIXTURES) or 46” (3 FIXTURES) 2-3/8”...
  • Page 4: Tools Required

    SECTION 3: 10”x10” BOLT PLATE INSTALLATION TOOLS REQUIRED DIMENSIONS PARTS USED Hole Depth: 3’ PART PART DESCRIPTION QTY Shovel Hole Size: 2’ x 2’ BOLT PLATE Concrete J-BOLT + HARDWARE REBAR Tape Measure Level INSTRUCTIONS STEP 1: Build a 2’ x 2’ frame out of 2” x 4” lumber & lay it on the ground where you want the hoop installed.
  • Page 5: Parts Used

    SECTION 4: LIGHT POLE INSTALLATION *INSTALLATION REQUIRES 2-3 ADULTS MINIMUM. ENSURE BOLT PLATE & CONCRETE HAS HAD AT LEAST 72 HOURS TO SET. TOOLS REQUIRED Phillips Head Screwdriver Allen Wrench: 7/32” Crescent Wrench PARTS USED PART PART DESCRIPTION TUBE 1 WITH BASE TUBE 2 TUBE 3 BULL HORN...
  • Page 6 STEP 4: Wired Light System: A. Feed wire from conduit at the bottom of the Light Pole up to the top of the pole. B. Secure Light Fixture onto the Top Tenon of the Bullhorn (Part G) and adjust to desired angle. Hand tighten set screws on fixture to the tenon.
  • Page 7 ◦ Remove the screws from the Anchor Cover (Part H). See Figure 11. STEP 9: ◦ Encase the bottom of the Light Pole with the Anchor Cover and secure the two halves with the (4) screws. See Figure 12. Figure 12 Figure 11...
  • Page 8 SECTION 5: WARRANTIES & POLICIES BASKETBALL STANDARD LIMITED LIFETIME WARRANTY Subject to the limitations set forth below, HomeSports (the “Manufacturer”) warrants to the original consumer purchaser (the “Purchaser”) of the Dominator Basketball Standard (hereinafter referred to as the “Dominator”) that the Dominator shall be free from material defects in parts and/or workmanship that impair the use of the Dominator for so long as the Purchaser owns the Dominator.
  • Page 9 This Return Policy applies to the purchase of the Dominator® Basketball Standard (hereinafter referred to as the “Dominator”) by the original consumer purchaser (“you” or the “Purchaser”) from Leap Innovations (the “Manufacturer”). 1. Any offer for free shipping by the Manufacturer applies ONLY to backboard) prior to signing for the delivery for damage during transit shipments within the domestic 48 continental United States.