Advertisement
Table of Contents
Advertisement
Table of Contents
Related Manuals for Young Electric FELLOW
Summary of Contents for Young Electric FELLOW
- Page 2 Parts...
-
Page 3: Parts List
Part# Description Parts List φ16 Spring Washer Part# Description φ16 Flat Washer Rotating Group Velcro Bottom Fixing Bracket Semicircle Plate φ16 Bent Pin M16*85 Hexagon Boltt Required Tools（Not included） M16 Lock Nut Name Imperial Metric φ3.8 Pin Monkey Wrench 12’’ 300mm M10 Short Outer Hexagon Bolt Open Wrench... - Page 4 bottom as shown in the figure to eliminate the gap between the STEP1 Bottom Fixing Bracket (2) and the Rotating Group (1). Note: Do not overtighten the bolts to prevent the Bottom Fixing Bracket (2) and the Rotating Group (1) components from rotating easily.
- Page 5 STEP2 STEP3 Insert the Left and Right Wheel Holder (9, 10) into the Beam Insert the component in step 2 into the component in step 1, and Assembly (8) respectively, then center them appropriately to fit fasten them with the Reinforcement Plate (11), put the 8 Flat the distance between bike tire.
- Page 6 STEP4 STEP 50Nm Place the Semicircle Plates (23) on both sides of the Support Rod Install the adjustable Connecting Block (18) to the Support (15), insert the Semicircle Plates (23) and Support Rod (15) (15), then tighten the knob from the Connecting Block (18). together into the base of the Bottom Fixing Bracket (2), align the holes, and then fix them with the M10 Low Square Neck Bolt (16) and the M10 Lock Nuts (17)
- Page 7 secure it with the φ3.8 pin (6), making sure to place the pin STEP6 through the holes on the bolt. The diameter of lock beam should be less than 7mm. The lock is not included. 2" Align the holes of the folding tube with the holes on the vehicle’s 2’’...
-
Page 8: Folding Steps
Folding Steps ∶ Use Velcro(22) to secure the Support Rod(15) and Beam Assembly(8) · Lower the Support Rod(15). together. ∴ ∷ Pull out the φ3.8 Pin (6) and φ16 Bent Pin (3) in Insert the φ16 Bent Pin(3) and the φ3.8 Pin (6). sequence, then lift the rack upwards. - Page 9 Bike Installation Instructions Snap the front tire of the ebike into the front wheel holder, place the rear tire in the beam, and then use the ratchet wheel straps to fix the front wheel, rear wheel, and seat tube of the bicycle as shown in the figure below. Please place one bike on the side which is close to the vehicle first, and install the Connecting Block (18) after the bike is fixed.
- Page 10 Bike Installation Instructions（tire width<2.5”） If your tire width is less than 2.5”, please use velcros to fasten the front and rear tires. Only 4pcs of Velcro(22) are required to fix the tires, the rest are for spare. Please keep the fixing method of velcro the same for the bike on the other side.
-
Page 11: Technical Specifications
Not intended for use with mopeds, motorcycles or 3 wheels bikes Applicable for tires width within 5”, extra velcros (included) ⚫ need to be applied for tires within 2.5” Model Name YOUNG ELECTRIC Fellow Description 2'' Hitch 2-Bike Rack Material Steel Maximum Weight Capacity... - Page 12 ⚠ WARNINGS ⚠ ⚫ Do not overload beyond the bike rack’s weight capacity of 200lbs. ⚫ Do not carry more than 2 bikes on the carrier. ⚫ The bike rack is not intended for transporting humans or animals. If you are planning to load only one bike, it is recommended to place it in the position closest to the vehicle. ⚫...
- Page 13 Young Electric Warranty Policy product or the issuance of a refund or credit (as determined by Young Electric is committed to providing our customers with a Young Electric) is a purchaser’s exclusive remedy under this quality shopping experience, for the products we sell, we provide warranty.
-
Page 14: Get Support
Get Support https://youngelectricbikes.com support@youngelectricbikes.com Toll Free Number: 888-933-8899...
Need help?
Do you have a question about the FELLOW and is the answer not in the manual?
Questions and answers