Sealey LP352.V3 Instructions

Thank you for purchasing a Sealey product. Manufactured to a high standard this product will, if used according to these instructions
and properly maintained, give you years of trouble free performance.
IMPORTANT: PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS, WARNINGS AND CAUTIONS.
USE THIS PRODUCT CORRECTLY AND WITH CARE FOR THE PURPOSE FOR WHICH IT IS INTENDED. FAILURE TO DO SO MAY CAUSE
DAMAGE AND/OR PERSONAL INJURY AND WILL INVALIDATE THE WARRANTY. PLEASE KEEP INSTRUCTIONS SAFE FOR FUTURE USE.
1. SAFETY INSTRUCTIONS
WARNING! Disconnect the heater from the gas supply before changing accessories, servicing or performing any maintenance.
!
Keep the heater clean and in good working order.
"
Check that the heater is in sound condition and not damaged. Take immediate action to repair or replace damaged parts.
"
Use recommended parts only. Unauthorised parts may be dangerous and will invalidate the warranty.
"
Store gas cylinders in accordance with regulations applicable to such appliances and DO NOT store below ground level.
"
Follow instructions to ensure that there are no leaks in the gas connections. DO NOT use a naked flame to check for gas leaks.
"
Use only a soapy water solution.
Use the supplied pressure regulator only. Protect regulator from rain and other contamination and DO NOT allow vent hole in regulator
"
cover to become obstructed.
For outdoor use only. The heater must have adequate continuous ventilation.
"
Should the heater not work correctly, immediately turn off the heater and close the gas valve. Check the heater according to instruction
"
manual. If you are unable to resolve the problem contact your local service agent. DO NOT attempt to dismantle or make any adjustments
beyond those mentioned in these instructions. To do so may be dangerous and will invalidate the warranty.
DO NOT use the heater on recreational vehicles or boats.
#
DO NOT use the unit for the heating of domestic premises.
#
DO NOT use the heater if damaged. Take immediate action to repair or replace damaged parts. Use authorised service agent only.
#
DO NOT use heater in closed rooms, living areas, basements or below ground level or in any area which is without adequate ventilation.
#
DO NOT use heater when there is a risk of strong winds blowing it over.
#
DO NOT allow untrained persons to ignite the heater.
#
DO NOT use a naked flame to try and ignite the heater.
#
DO NOT use the heater near flammable material, liquids, solids, or gases or in areas where spray painting is carried out.
#
DO NOT place any flammable material within 2mtr of the heater.
#
DO NOT place any other object less than 1mtr from the heater.
#
DO NOT attempt to move the heater when it is lit, wait until it has been switched off and allowed to cool down.
#
DO NOT touch any part of the operating heater above the control switch, as serious burns could result. Allow one hour cooling after switch
#
off to ensure safety.
DO NOT expose the cylinder to the sun, or any other heat source.
#
Ensure the cylinder valve is closed when the heater is switched off.
"
When not in use remove the cylinder and store the cylinder and heater in a safe, dry area, out of reach of children.
"
WARNING!
!
If the heater is used for prolonged periods at maximum power, ice may form on the propane cylinder. If so, DO NOT use another heater to de-ice
the cylinder. Allow the ice to melt naturally.
2. INTRODUCTION & SPECIFICATION
The LP352 and LP352S heaters are for use out of doors or in large well ventilated indoor spaces. The
heater uses propane gas to generate infrared heat from the upper heat unit which is reflected down and
out by a conical plate inside the head shield. The radiant heat produces a warm area covering
approximately 20-25mtr depending on location and conditions.
2
2.1. Specification:
Nominal Output . . . . . . . . .12.0kW
Fuel . . . . . . . . . . . . . . . . .Propane
Ignition . . . . . . . . . . . .Piezoelectric
Reflector . . . . . . . . . . . . .Ø815mm
Note: Gas cylinder is not supplied.
3. CONTENT
3.1. Content
Note: The flame screen may be slightly blackened. This is a result of factory tests and is not a
fault. Remove from packing and check parts against the list below. If any parts are missing or
damaged contact your supplier immediately.
6 x Nuts and Bolts (M6) x 35mm
3 x Bolts (M8) x 16mm
3 x Inner support posts
1 x Column
3 x Wing Nuts
3 x Reflector support pins
2 x 10mmM8 bolts
Height . . . . . . . . . . . . . . .2240mm
Weight (excluding cylinder) . .17kg
Pressure . . . . . . . . . . . . . .28mbar
2 x Jubilee clips
4 x M6 x 10mm
1 x Base
1 x Flame screen/control assembly
6 x Washers Ø8mm
3 x Wing nuts
INSTRUCTIONS FOR:
P R O PA N E S PA C E H E AT E R S
LP352.V3 & LP352S.V2
MODELS:
1 x Reflector
1 x Gas Hose
1 x Gas Regulator
1 x Tank housing
1 x Wheel bracket
2 x M8 Nuts
LP352.V3, LP352S.V2 - 1 - 300707
INFRARED