Advertisement
Quick Links
Description
TITAN VERSA HIGH-FLOW VALVE KITS
P/N
TV115787
TV115787-1
TV115801
TV115801-1
TV115802
TV115802-1
TV115803
This manual is intended for users needing to install TITAN VERSA High-
Flow valves on their own.
The TITAN VERSA High-Flow Evacuation (Evac) valve reduces pump
down times by 50%. The High-Flow vent valves greatly reduce typical
vent times thereby improving overall cycle times.
Installation
NOTICE: This section references installing both High-Flow Evac and
High-Flow Vent valves. Adjust installation if only one of the two
valves are being installed.
1. Remove electrical power.
2. Remove external covers (see section 8.8 of main user manual).
Remove screen connector
SMT-07-1046 B1
TITAN VERSA HIGH-FLOW VALVES
Description
VERSA C (Compact) High-Flow Evacuation Assembly
VERSA C (Compact) High-Flow Evacuation w/ High-Flow
Vent
VERSA L (Horizontal) High-Flow Evacuation Assembly
VERSA L (Horizontal) High-Flow Evacuation w/High-Flow
Vent
VERSA T (Tower) High-Flow Evacuation Assembly
VERSA T (Tower) High-Flow Evacuation w/ High-Flow
Vent
TITAN VERSA High-Flow Vent Valve Assembly
.
User Manual
Advertisement
Subscribe to Our Youtube Channel
Related Manuals for LACO Technologies TITAN VERSA
Summary of Contents for LACO Technologies TITAN VERSA
- Page 1 Vent TV115803 TITAN VERSA High-Flow Vent Valve Assembly This manual is intended for users needing to install TITAN VERSA High- Flow valves on their own. The TITAN VERSA High-Flow Evacuation (Evac) valve reduces pump down times by 50%. The High-Flow vent valves greatly reduce typical vent times thereby improving overall cycle times.
- Page 2 3. Remove the aluminum electrical board cover with a 2mm hex wrench. 4. Remove Accessory Cables: Disconnect all wires, except middle COM terminal, from the J8 (Relay Contacts) terminal block using a small flat head screwdriver. 5. Remove the two blue 0V wires connection from the 0V terminal block.
- Page 3 ACCS 2 cable (LCA074) to left side of bracket. ACCS 2 ACCS 1 8. Re-connect the ACCS cables to terminal block J8 (Relay Contacts) on Titan Versa electrical board per the table below. Wire color Termination Accessory 1...
- Page 4 Accessories). 2. If applicable change Accessory 1 to High-Flow Evac and press Save. See the main Titan Versa User Manual for details on all the various High-Flow Evac settings. 3. If applicable set Accessory 2 to High-Flow Vent and press save.
- Page 5 4. Run preliminary leak tests cycles with the covers off and verify the High-Flow valve LED’s in valve DIN connector modules are lighting 5. Leak Test Instructions: Attach an NW-25 blank off to Inlet Tee (for Compact and Tower Versa, blank off pump port as well). In Vacuum test mode, put leak detector into a test cycle.
- Page 6 Table 1: High-Flow Evac. Plumbing Versa Conf. 1 Pump 2 Pumps Compact Tower Horizontal...
- Page 7 Table 2: High-Flow Vent Plumbing Versa High-Flow Vent Only High-Flow Evac & Vent Conf. Compact Tower Horizontal...
-
Page 8: Maintenance
Maintenance Valves should be inspected and cleaned every 100,000 cycles or every two years (whichever comes first). Valve plunger seals and the internal valve body should be lightly cleaned with methanol or water if dirty or contaminated. Follow the valve replacement instructions below to inspect valves.
Need help?
Do you have a question about the TITAN VERSA and is the answer not in the manual?
Questions and answers