Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Subscribe to Our Youtube Channel
Related Manuals for Diamond Products CPS1300
Summary of Contents for Diamond Products CPS1300
- Page 1 CORE PREP OPERATOR'S MANUAL CPS1300 SCARIFIER NOVEMBER, 2024...
-
Page 3: Table Of Contents
Table of Contents Description Page No. 1. General Safety Precautions....................... 1.1. S e e Sc i e s e s............1.2. Labels on the CPS1320E3 & CPS1325LCE3 sc i e ..........1.3. c i e e ide i c i e CPS1320E3............... -
Page 4: Product Overview
Product Overview CPS1320E3 ve vie 1 Handle complete with control panel 2 Drive 3 Milling housing 4 Swing 5 Motor-Drive Belt for front wheel... - Page 5 Product Overview CPS1325LCE3 (Low Chassis) Option with adjustable Hand wheel ve vie CPS1325LCE3 ssis All individual parts and explosions diagrams can be found listed in our separate CPS1320E3 AND CPS1325LCE3 Spare Parts List.
-
Page 6: General Safety Precautions
General Safety Precautions Safety rules for the operation of the Scarifi ers/Planers Information e CPS1320E3 c ed cc di e is i tions. These technical precautions should not be removed or changed under any circum- stances. While operating the machines the following points should also be kept in mind: Danger! •... -
Page 7: Labels On The Cps1320E3 & Cps1325Lce3 Sc I E
Labels on the CPS1320E3 & CPS1325LCE3 fl oor scarifier DOWN Labels on the CPS1320E3 sc i e 1. Warning - electrical voltage. es e UP - turn wheel in arrow direction for lifting the tools from the ground. 3. DOWN - direction of lowering the tools to the ground. Wait! Before switching from STAR to DELTA - wait at least 10 seconds. -
Page 8: Operating The Machine
Diamond Products. The use of the machining outside is only possible in dry weather. The operation must only be carried out in conjunction with a recommended dust collector from Diamond Products. -
Page 9: Adjusting The Tool Drum
si i Danger! Excessive depth settings by lowering the tools too much decreases the performance of the machine. The shafts in the drum and the bearings of the machine may also be destroyed. Adjusting the tool drum Hand wheel Rear wheel Clamping screw Adjusting the tool drum During the operation of the CPS1320E3... -
Page 10: Changing The Tool Drum
Changing the tool drum ATTENTION! Before any maintenance, the machine must be brought to a complete stand still. Always disconnect the machine if it is an electric model. c i e i e eve s e e c e • •... -
Page 11: Technical Data
Technical Data 118 cm 98 cm Technical Data for the CPS1320E3 & CPS1325LCE3 Parameter Value Working width 32 cm (12.5 in) Machine width 61 cm (24 in) Machine heightt 118 cm (47 in) Machine length 98 cm (39 in) Weight with drum 270 / 300 kg (595 / 661 Ibs) Motor rotation speed 2935/2935 rpm / Drive Unit 3000 rpm... -
Page 12: Tools For The Drum
Tools for the drum Tools for the CPS1320E3 Parameter Value Drum diameter 225 mm (10 in) Cutter shaft diameter 2 cm (0.82 in) Number of shafts TCT cutter 80/8 Milling cutter 80/20 Cutter diameter 80 mm Max No. of TCT cutters Max. -
Page 13: Trouble Shooting
Trouble Shooting Trouble Shooting Problem Possible cause Solution Machine does not – Check the network supply – – Eliminate the fault by a specialist or replace parts – Defective fuse cable or – Turn switch to zero plug defective se i –... -
Page 14: Notes
NOTES ____________________________________________________ ____________________________________________________ ____________________________________________________ ____________________________________________________ ____________________________________________________ ____________________________________________________ ____________________________________________________ ____________________________________________________ ____________________________________________________ ____________________________________________________ ____________________________________________________ ____________________________________________________ ____________________________________________________ ____________________________________________________ ____________________________________________________ ____________________________________________________ ____________________________________________________ ____________________________________________________ ____________________________________________________ ____________________________________________________ ____________________________________________________ ____________________________________________________ ____________________________________________________ ____________________________________________________ ____________________________________________________ ____________________________________________________ ____________________________________________________ ____________________________________________________ ____________________________________________________... -
Page 16: Warranty
(1) year from the date of shipment to Customer. The responsibility of Diamond Products under this Warranty is limited to replacement or repair of defective parts at Diamond Products’ Elyria, Ohio...
Need help?
Do you have a question about the CPS1300 and is the answer not in the manual?
Questions and answers