Directory Page Content number Directory Safety instruction Packaging Details Assembly instructions Instructions for electric control System operation guide Maintenance guidelines General errors and troubleshooting Maintenance clauses Warm-up exercise Guidance on safe use This machine is designed and manufactured to consider many safety issues, to ensure your safety, before using this machine, be sure to read all the contents of this manual, for safety.
Page 3
Warning 1. Before using this machine, make sure the machine is fully grounded to avoid accidents and hazards 2. When running, please clamp the safety lock (red) clip in the appropriate position clothes to facilitate the emergency to pull off the safety lock and stop the machine to ensure safety. 3.
Packaging Details Series Components number Main frame Electronic watch bezel Side protection cover User manual Screw package Accessories Series Quantit Components number Security key 1 pc 6 mm hex key 1 pc Lubricating oil 1 bottle M8 * 16 half-round hex screws 8 pcs M8 flat washer 10 pcs...
Assembly instructions Step 1 Lift out the main frame and the electronic meter frame from the carton and open the bundles of the frame. Step 2: Pull up the column in the direction of the arrow, use F # M8*40 inner circle head hex screw and D#M8*16 inner half circle head hex screw, and attach it to the sub frame.
Page 6
: Step 4 Attach the side cover to the pillar and base frame with the J#ST4*16 screws as shown in the figure : Step 5 At this time, the electronic clock on the lamp lights up, press the start button the machine can be run! (Note: the safety lock must be placed on the yellow sticker position in the center of the meter before the treadmill can start normally;...
the platform in the direction of the arrow until the air spring makes a "clipping" sound. Product expansion: with the foot as follows light kick air spring card position, you can expand the product. Operating instructions for electronic control Using 1.
Page 8
Start Start normally after 3 second countdown 5. Programs 3 manual programs, 12 automatic programs. 6. Security key function Disengage the safety lock and immediately show "E07" the treadmill to stop quickly and beep alarm sound appears, turn on the safety lock when the electronic clock full display 2 seconds, all data zero 7.
Page 9
located on the handle. 7.6 speed shortcut Adjust directly to the corresponding speed,3KM,6KM,9KM,12KM on the display control panel press speed shortcut 2 7.7 Inclined Hotkeys Press the tilt shortcuts 3, 6, 9 and 12 on the display control panel to adjust directly to the appropriate height.
Page 10
SPEED SPEED SPEED SPEED SPEED SPEED SPEED set time/10 = run time for each slope segment INCL. PROG INCL INCL INCL INCL INCL INCL INCL INCL INCL INCL INCL INCL 10 Parameter setting in 3 modes 10 .1 The countdown is initially set to 10:00 minutes, with an interval of 5:00-99: 59 minutes and a step of 1:00.
Page 11
10 .3 The reverse distance is set to the initial distance, the setting range is 1.0-, step 1.0. 1.0 km 99.9 Cycling order is: manual, time, distance, calories. 1.1 Physical fitness test (FAT): Press the PROG button to select FAT (Body Fat Calculator Program). The computer screen shows FAT.
set the parameters countdown, others show forward counting. The default value for calories is 30 kcal/km. The acceleration is / S0.1 Km, and the deceleration is / S0.1 Km Maintenance guidelines Proper maintenance can always keep your treadmill in top condition, incorrect maintenance can damage or shorten the life of the treadmill.
Page 13
When you use the treadmill, the pressure on the treadmill is unbalanced because the two feet are not the same when running, which results in the running belt deviating from the center. This the deviation is normal, and when no one is running on the treadmill, it will automatically return to normal center.
General errors and troubleshooting 1.Electronic display error code and exclusion Troubleshooting Error Error description codes Lower the control shutdown to the fault state. Unable to start. Abnormal The electronic meter displays the error code and the buzzer communication: rings 3 times. Possible causes: electronic control and electronic abnormal meter communication blocked, check the electronic meter to the communication...
Page 15
Stop into the error state, electronic meter buzzer ring 9, at the same time display error code, the rest of the area does not Over current display content. Keep error state about 10 seconds after protection: in entering standby mode, can restart. Possible causes: too high operating mode, load leads to too high current, system self-protection or part of the DC motor...
Exclusion Guidelines: 2.1 Check that the input voltage is within the permitted range. 2.2 Check that the power switch of the running machine is on. 2.3 Check that the fuse in the electrical outlet is fused. If it is blown, replace it with a spare fuse. 2.4 Check the controller to see if the LEDs are on.
Practice notes ● consult your doctor before starting a sports or exercise program, follow your doctor's advice and guidance. ● set exercise goals after consulting your doctor to ensure the plan is realistic and starts the training plan calmly. ● you can add some aerobic exercise to your exercise plan, such as walking, jogging, swimming, dancing or cycling.
Page 18
3. Tendon extension of leg and heel: Hold onto the wall or stand with both hands, one-foot behind, back leg straight, heel on the ground, lean against the wall. Hold for 10-15 seconds and then relax. Repeat 3 times for each leg. 4.
Need help?
Do you have a question about the EPSILON MARATHON 200 and is the answer not in the manual?
Questions and answers