Safety Information
IMPORTANT SAFETY
INSTRUCTIONS
When using electrical products, basic precautions should always be
followed including the following:
READ AND FOLLOW ALL
a)
SAFETY INSTRUCTIONS.
b) This product is for indoor use only. The electrical rating 0.24 A 120 V
60 Hz.
c) Do not use this product outdoors.
d) This seasonal use product is not intended for permanent installation
or use.
e) Do not mount or place near gas or electric heaters, fireplace, candles
or other similar sources of heat.
f) Do not secure the wiring of the product with staples or nails, or place
on sharp hooks or nails.
g) Do not let lamps rest on the supply cord or on any wire.
h) Unplug the product when leaving the house, or when retiring for the
night, or if left unattended.
i) This is an electric product – not a toy! To avoid risk of fire, burns
personal injury and electric shock it should not be played with or placed
where small children can reach it.
j) Do not use this product for other than its intended use.
k) Do not hang ornaments or other objects from cord, wire, or light
string.
l) Do not close doors or windows on the product or extension cords as
this may damage the wire insulation.
m) Do not cover the product with cloth, paper or any material not part of
the product when in use.
n) Do not move the tree by pulling the tree tips or tree branches.
o) This product is equipped with push-in type lamps. Do not twist lamps.
p) This product employs overload protection (fuse). A blown fuse
indicates an overload or short-circuit situation. If the fuse blows, unplug
the product from the outlet. Also unplug any additional strings or
products that may be attached to the product. Replace the fuse as per
the user servicing instructions (follow product marking for proper fuse
rating) and check the product. If the replacement fuse blows, a
short-circuit may be present and the product should be discarded.
q) Read and follow all instructions that are on the product or provided
with the product.
SAVE THESE INSTRUCTIONS.
r)
CAUTION!
–
ALWAYS UNPLUG YOUR
TREE FROM ITS POWER SOURCE BEFORE
ASSEMBLING OR DISASSEMBLING.
CAUTION
a) To reduce the risk of electric shock, use only with the
power-supply cord provided or with a cord set intended for outdoor
use.
b) Do not use a cracked, frayed, or damaged cord. Inspect the cord
periodically.
c) Do not abuse cord – Do not carry product by the cord or yank or
pull it to disconnect from the outlet.
d) Disconnect the product from the outlet when not in use.
7ft Douglas Fir Mini Warm White LED Pink Tree
SKU# 1005232499
Pre-Assembly
Package Contents
A. Tree top
B. Tree center
Qty: 1
Qty: 1
D. Stand with an
E. Fuse
eye bolt
Qty: 2
Qty: 1
Assembly
Assembling the tree stand
Step 1. Choose a location near a wall outlet.
Step 2. Open the stand to a 90 degree angle until the hole lines up with the
hole on the tube.
Step 3. Screw an eye bolt into the hole.
CAUTION! – ALWAYS UNPLUG YOUR
TREE FROM ITS POWER SOURCE
BEFORE ASSEMBLING OR
DISASSEMBLING.
Assembling the tree
Please remove protective covers from the base of the pole for each tree
section before assembling.
Step 1. Carefully insert bottom section (C) of tree into tree base and
tighten the screw. (See Fig. 1)
Step 2. Insert the middle section (B) of the tree into the bottom section (C).
(See Fig. 2)
Step 3. Insert the top section (A) into the middle section (B). (See Fig. 3)
Step 4. Insert the male connector of the middle section (B) into the
female connector of the top section (A), the male connector of
the bottom section (C) into the female connector of the middle
section (B) in right direction properly and tightly and then lock
the hook on the connectors according to the magnified
drawing on Fig. 6). (See Fig. 4, 5, 6)
C. Tree bottom
Qty: 1
F. Replacement
G. Latch
Bulb
Qty: 2
Qty: 6
Need help?
Do you have a question about the 1005232499 and is the answer not in the manual?
Questions and answers