Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for Miele SmartBiz PDR 1108 HP
Summary of Contents for Miele SmartBiz PDR 1108 HP
- Page 1 Operating and installation instructions Heat-pump tumble dryer It is essential to read these operating instructions before installing and using the appliance. This prevents both personal injury and damage to the appliance. en-AU, NZ M.-Nr. 12 549 420...
-
Page 2: Table Of Contents
Using for the first time ....................20 Installation........................20 Information about networking ..................20 Miele@home......................20 Wash2Dry ......................21 Setting up Miele@home ....................21 1. Notes on correct laundry care................22 Washing ........................... 22 Drying ..........................22 Garment care label symbols ..................22 2. - Page 3 Contents Changing the programme sequence................. 33 Changing a programme after it has started..............33 Adding or removing laundry ..................33 Fragrance flacon......................34 FragranceDos........................34 Removing the protective seal from the fragrance flacon.......... 34 Inserting the fragrance flacon..................35 Opening the fragrance flacon ..................36 Closing the fragrance flacon ..................
- Page 4 Contents Installation........................56 Downtime after installation..................56 Levelling the tumble dryer ..................56 Room ventilation ....................... 57 Drain hose for condensed water .................. 58 Electrical connection ..................... 60 Technical data ........................ 61 Consumption data ......................62 Programmable functions ..................... 63 Programming........................
-
Page 5: Caring For The Environment
Please dispose of it at your local community waste collection/recycling centre for electrical and electronic appliances, or contact Miele. You are also responsible for deleting any personal data that may be stored on the appliance being disposed of. Please... -
Page 6: Warnings And Safety Instructions
“Installation”, as well as in the “Warning and Safety instructions”. Miele cannot be held liable for injury or damage caused by non- compliance with these instructions. Keep these operating instructions in a safe place and pass them on to any future owner. -
Page 7: Technical Safety
The protective measures provided in the installation and in this Miele product must also be assured in their function and operation in isolated operation or in non-mains synchronous operation, or replaced with equivalent measures in the installation. - Page 8 (e.g. danger of overheating). If the electrical connection cable is faulty, it must only be replaced by a Miele authorised service technician to protect the user from danger. The electrical safety of this appliance can only be guaranteed when ...
- Page 9 It is not suitable for room lighting. Replacement lamps may only be fitted by a Miele authorised technician or by Miele Professional Service. The R290 refrigerant contained in this tumble dryer is flammable ...
-
Page 10: Correct Use
Warnings and safety instructions This tumble dryer uses a gaseous refrigerant which is condensed by the compressor. Having been increased to a high temperature level by compression, the refrigerant passes through a closed refrigerant circuit. The heat generated is transferred to the drying air as it passes through the heat exchanger. - Page 11 Warnings and safety instructions Do not lean on the door. Otherwise, the tumble dryer may tip over, causing injury to yourself or others. Always close the door after use. This way you will avoid the danger - children climbing into the tumble dryer or hiding things in it. - pets or other small animals climbing into the tumble dryer.
- Page 12 Warnings and safety instructions If the water is drained externally, make sure the drain hose is secured against slipping, e.g. if you hang it in a laundry tub or laundry trough. Otherwise the hose may slip off and the condensation water flowing out may cause damage.
- Page 13 Warnings and safety instructions thoroughly cleaned, there is a danger that they might ignite when heated, even after they have been removed from the tumble dryer at the end of the programme. - Items (e.g. mops and floor cloths) that have been treated with inflammable cleaning agents or which contain residues of acetone, alcohol, benzene, petrol, kerosene, stain remover, turpentine, wax and wax remover or other chemicals.
- Page 14 Warnings and safety instructions The following mandatory requirements must be met: - permanent room ventilation from the beginning to the end of every drying programme. - a gap between the floor and the bottom of the tumble dryer (this must not be blocked or obstructed in any way). Do not expose the dryer to air which contains chlorine, fluorine or ...
- Page 15 Warnings and safety instructions Using a fragrance flacon (optional accessory) Only ever use original Miele fragrance flacons. The fragrance flacon must be stored in its packaging so please make sure you retain this. Make sure that you always keep the fragrance flacon, or the fluff ...
- Page 16 Please ensure that the washer-dryer stacking kit is suitable for your Miele tumble dryer and your Miele washing machine. If you order a plinth for this tumble dryer (available from Miele as an optional accessory), make sure it is the correct one.
-
Page 17: Operating The Tumble Dryer
Operating the tumble dryer Control panel a Control panel f Sensors for time selection b Sensors for the drying levels g Start/Add laundry sensor c Indicator lights Touching the Start/Add laundry light up when necessary sensor starts a programme. -
Page 18: How The Programme Selector Works
MobileStart You can operate your tumble dryer remotely with the Miele App. The , , , and sensors react to Wash2Dry fingertip contact. Selection is possible A drying programme tailored to the as long as the respective sensor is laundry is set automatically in illuminated. -
Page 19: Drum Lighting
Operating the tumble dryer Indicator lights The electronics will continually assess the conditions and adjust the - programme duration with increasing lights up if condensate drainage via accuracy. the drain hose is hindered. Sensor controls - ... -
Page 20: Using For The First Time
- a Wi-Fi network For information about availability, please - the Miele App visit www.miele.com. - a Miele user account. You can create a Miele App user account via the Miele App. You can download the Miele App from The Miele App will guide you as you ®... -
Page 21: Wash2Dry
Miele Cloud. The tumble dryer automatically sets a Signing on via the Miele App drying programme tailored to the The Miele App can be used to connect laundry based on the transferred to your network. programme data. -
Page 22: Notes On Correct Laundry Care
1. Notes on correct laundry care Washing Garment care label symbols - Wash heavily soiled laundry Drying thoroughly. Ensure that you use normal/higher temperature sufficient detergent and select a high temperature. If in doubt, wash the reduced temperature* items several times. -
Page 23: Loading The Tumble Dryer
2. Loading the tumble dryer Loading the laundry Checking the socket for the fragrance flacon Textiles can be damaged. If you are not using a fragrance flacon, Before loading the dryer, read “1. check that the socket is closed. Notes on correct laundry care”. See "Fragrance flacon"... -
Page 24: Selecting A Programme
MobileStart programme selector position Turn the programme selector to MobileStart . will light up in the time display. Touch the Start/Add laundry sensor. The tumble dryer can now be operated via a mobile device together with the Miele App. -
Page 25: Selecting Programme Settings
3. Selecting a programme Selecting the Warm air duration Selecting programme settings You can set the duration in ten-minute Selecting the drying level increments from minutes Check the “Programme chart” to see to hours. which programme you can select a drying level for and which drying level meets your requirements. -
Page 26: Starting A Programme
4. Starting a programme Energy saving Starting a programme Indicators are switched off after Touch the flashing Start/Add laundry 10 minutes. The Start/Add laundry sensor. sensor flashes slowly. The Start/Add laundry sensor lights up. Touch the Start/Add laundry sensor Programme sequence to switch the indicators on again (this does not have any effect on a running... -
Page 27: End Of Programme - Unloading The Drum
5. End of programme - unloading the drum At the end of the programme Removing the laundry The laundry is cooled down shortly before the end of the programme. The laundry can then be removed. The programme has ended when only ... -
Page 28: Delay Start/Smartstart
Delay start/SmartStart Selecting Delay start Starting Delay start Touch the Start/Add laundry sensor With Delay start you can delay the to start the Delay start function. start of a programme from minutes up to (hours). - Delay start times of more than will count down in hours and then in Delay start cannot be used with the minutes until the start of the... -
Page 29: Smartstart
Delay start/SmartStart Setting the timeframe SmartStart If the SmartGrid programmable The SmartStart function (only available function is activated, the function of in selected countries) lets you define a the sensor changes. The time time period during which your tumble display no longer shows the Delay dryer will start automatically. -
Page 30: Programme Chart
Programme chart All weights marked with * are based on the weight of dry laundry. Cottons Max. load 8 kg* Extra dry, Cupboard Dry Items - Single and multi-layered cotton fabrics. - Towelling, bathrobes, T-shirts, underwear, jersey/terry bed linen, baby clothes. - Workwear, jackets, cotton blankets, aprons, tea towels, bed linen, towels, overalls, table linen. - Page 31 Notes This programme only dries to the Cupboard Dry level. MobileStart The Miele App is used to select programmes and operate the appliance. Wash2Dry The programme is selected automatically in conjunction with the programme selection on the connected washing machine.
- Page 32 Programme chart Express Max. load 4 kg* Extra dry, Cupboard Dry, Hand iron, Machine iron Items Hard-wearing textiles suitable for the Cottons programme. Notes Shorter programme duration Microfibre Max. load 7 kg* Extra dry, Cupboard Dry Items Microfibre mops and cleaning cloths.
-
Page 33: Changing The Programme Sequence
Changing the programme sequence Changing a programme after it Adding or removing laundry has started You have forgotten an item of laundry, but the programme has already started. It is no longer possible to change the selected programme. This prevents the ... -
Page 34: Fragrance Flacon
Fragrance flacon FragranceDos Removing the protective seal from the fragrance flacon Fragrance flacons (optional accessories) can be used to give your Only hold the fragrance flacon as laundry a pleasant scent. illustrated. Do not hold it at an angle or tip it as the fragrance will leak out. This dryer has 2 places for inserting fragrance flacons. -
Page 35: Inserting The Fragrance Flacon
Fragrance flacon Inserting the fragrance flacon Open the door of the tumble dryer. The fragrance flacon is inserted in the upper fluff filter. It can be inserted on the left or the right-hand side beside the grip. Insert the fragrance flacon in the opening as far as it will go. -
Page 36: Opening The Fragrance Flacon
Fragrance flacon Turn the outer ring clockwise a little. The fragrance flacon can slip out. Turn the outer ring so that markers and line up. Opening the fragrance flacon Before drying, you can select the intensity of the fragrance. -
Page 37: Removing/Replacing The Fragrance Flacon
- Always store in a cool, dry place away fragrance flacon in its original packaging. from direct sunlight. Fragrance flacons are available to order - When purchasing new fragrance from Miele or online at www.miele- flacons, only remove the protective shop.com. seal just before use. -
Page 38: Cleaning And Care
Cleaning and care Observing cleaning intervals Cleaning the filters This tumble dryer is equipped with a This tumble dryer has 2 fluff filters in multi-stage filter system, which the door opening: The upper and lower consists of fluff filters and a filter in the fluff filters trap fluff produced during plinth. -
Page 39: Cleaning The Fluff Filters And Air Flow Openings Thoroughly
Cleaning and care Pull the upper fluff filter forward to Remove the fragrance flacon. See remove it. “Fragrance flacon”. Pull the upper fluff filter forward to remove it. Remove the fluff (see arrows). Turn the yellow dial on the lower fluff filter in the direction of the arrow (until you hear it click). -
Page 40: Cleaning The Plinth Filter
Cleaning and care Use a vacuum cleaner with a long Push the lower fluff filter in crevice nozzle attached to remove any completely and lock it with the yellow visible fluff from the upper air flow dial. openings. Finally, clean the fluff filters with water. -
Page 41: Removing The Plinth Filter
There is insufficient flow of air and heat exchange in the heat exchanger, as it is clogged. This requires a visit from Miele Professional Service. Pull the plinth filter out by the handle. This can be avoided by following the... - Page 42 There will be an insufficient flow of Rinse and wash the entire plinth filter air and heat in the heat exchanger. until all visible residues have been This will require a visit from a Miele removed. technician. Gently squeeze out the plinth filter Before and after cleaning, check the until no more water comes out.
-
Page 43: Replacing The Plinth Filter
Cleaning and care Replacing the plinth filter Filter wear caused by continuous tumble dryer use. If the tumble dryer is in continuous use and is being cleaned frequently, the plinth filter can begin to show signs of wear after a while. This can clog up the heat exchanger. -
Page 44: Cleaning The Plinth Filter Panel
Cleaning and care Checking the heat exchanger Risk of injury from sharp cooling fins. You could cut yourself. Do not touch the cooling fins. Look to see if fluff has accumulated. If you notice any visible soiling: Damage due to incorrect cleaning of the heat exchanger. -
Page 45: Inserting The Plinth Filter
You must stop using the plinth filter if guide pins. it shows signs of wear or - The word Miele on the handle must be deformation. the correct way up. See the information in "Cleaning and care - Replacing the plinth filter". - Page 46 Cleaning and care Damage due to the use of unsuitable care products. Unsuitable care products can damage plastic surfaces and other parts. Do not use solvents, abrasive cleaners, glass cleaners or all- purpose cleaners. Risk of electric shock due to water.
-
Page 47: Problem Solving Guide
Problem solving guide Many malfunctions and minor faults that can occur in daily operation can be corrected without contacting Miele. This will save you time and money because you will not need a service call. You can find information on how to remedy faults yourself at www.miele.com.au/service or www.miele.co.nz/service and on the Miele website. - Page 48 Start a programme. cancelled, a signal tone If the programme terminates again with the same sounds. error message, then there is a fault. Contact Miele. : lights up and the The laundry is unevenly distributed or has rolled up. programme has been ...
-
Page 49: Unsatisfactory Drying Result
Problem solving guide Unsatisfactory drying result Problem Possible cause and remedy The laundry is not The load consisted of different types of fabric. sufficiently dry. Finish drying using the Warm air programme. Select a more suitable programme next time. Useful tip: You can alter the drying levels for some programmes. -
Page 50: The Drying Process Takes A Long Time
Problem solving guide The drying process takes a long time. Problem Possible cause and remedy The drying process goes The room in which the tumble dryer is located is too on for too long or even warm. switches off.* Ventilate the room thoroughly. Detergent residues, hair and fine fluff can clog the filters. -
Page 51: Other Problems
The drum lighting is faulty. The drum lighting is designed to last a long time and should not normally need to be replaced. If you have tried everything but the drum lighting still does not come on, contact the Miele Professional Service Department. -
Page 52: Service
Miele (see Miele. contact details at the back of these instructions). You can book a Miele customer service call-out online at www.miele.com.au/ service or www.miele.co.nz/service. Contact information for Miele can be found at the end of this booklet. -
Page 53: Installation
*INSTALLATION* Installation Front view a Mains connection cable f Intake for air cooling – do not obstruct with a laundry b Control panel basket or other objects c Door g Drain hose for condensed water d Fluff filter flap for the filter in the h Non-return valve, required plinth i Non-return valve, recommended... -
Page 54: Rear View
*INSTALLATION* Installation Side view Rear view 1054 a Protruding lid for holding when moving the tumble dryer (see arrows) View from above b Drain hose for condensed water c Hook for winding up the mains cable during transport d Mains connection cable 1054 Installation locations All measurements in mm... -
Page 55: Washer-Dryer Stack
Washer-dryer stack Transporting the tumble dryer A stacking kit* is required. This must be If the tumble dryer is being fitted by a Miele authorised service transported horizontally, it must only technician. be tipped onto its left or right side. -
Page 56: Installation
Installation - Disconnect the dryer from the electricity supply. - Air the room where the tumble dryer is located. - Contact Miele Customer Service. Downtime after installation Damage caused by switching the appliance on too soon. This can damage the heat pump. -
Page 57: Room Ventilation
*INSTALLATION* Installation The heat pump that is essential to the operation of this tumble dryer generates a great deal of heat inside its casing. There must be a reliable means of dissipating this heat. Otherwise loads could take longer to dry and the tumble dryer might sustain damage in the long term. -
Page 58: Drain Hose For Condensed Water
*INSTALLATION* Installation Drain hose connection options Drain hose for condensed water Useful tip: Follow the warnings The condensed water is pumped away regarding leakage or backflow of water through the drain hose which is when selecting one of the following located at the back of the dryer. - Page 59 *INSTALLATION* Installation Drainage accessories, supplied Fit the adapter 1 to the drain outlet using the nut 2. If this nut has a spacer you should take the spacer out first. Attach the end of the hose 4 to the adapter 1.
-
Page 60: Electrical Connection
*INSTALLATION* Installation The plug connector or isolator switch Electrical connection should be easily accessible at all times. This description applies to tumble Risk of electric shock! dryers both with and without a mains plug. If the dryer is disconnected from the power supply, protective measures The following applies to tumble dryers must be taken to ensure that the... -
Page 61: Technical Data
Max. floor load during operation 925 N Product safety standard AS/NZS 60335 A-rated sound emissions L <70 dB re 20 μPa accordance with EN ISO 11204/11203 Frequency band 2.4000 GHz – 2.4835 GHz Maximum transmission power < 100 mW Miele hereby declares that this heat-pump tumble dryer complies with Directive 2014/53/EU. -
Page 62: Consumption Data
Consumption data Load size Final spin Residual Energy Duration speed in moisture washing machine 1000 1.32 1000 0.75 Cottons, Cupboard Dry 1200 1.20 1400 1.15 1600 1.00 Cottons, Hand iron 1000 0.99 1200 0.85 1400 0.80 1600 0.70 Minimum iron, Cupboard Dry 1200 0.45 Woollens handcare... -
Page 63: Programmable Functions
Programmable functions Programming Programmable functions Factory default setting You can use the programmable functions to alter the dryer's Cottons drying levels electronics to suit your requirements. Minimum iron drying levels Programming is carried out by following these steps (, , ... ) using the Cooling down temperature ... -
Page 64: Factory Default Setting
Programmable functions Editing and saving the programmable X = can be selected, = factory default function Confirm your selection with the You can switch a programmable Start/Add laundry sensor. function on or off or select different The number of the programmable options. -
Page 65: Cooling Down Temperature
Programmable functions Options Buzzer volume = Even damper The buzzer volume can be changed. = Damper = On, quieter = A little damper = On (factory default setting) = Factory default setting = A little drier ... -
Page 66: Conductivity
Programmable functions Confirm with the Start/Add laundry = Off sensor. The time display and the Enter the two other numbers in the sensors do not go out. same way. = On (factory default setting) The tumble dryer is ready for use after The time display and the ... -
Page 67: Buzzer Active
Programmable functions = No Anti-crease = Off The indicator light does not = 1 hour light up. However, if there is a = 2 hours (factory default setting) very severe blockage in the ducting, the programme will be Buzzer active cancelled and the fault message ... -
Page 68: Welcome Tone
Miele’s RemoteUpdate function can follow the instructions in “Before only be used if the tumble dryer is using for the first time”. connected to a Wi-Fi network (see “Settings - Miele@home”) and you have an account in the Miele App. The... -
Page 69: Remote Control
Remote control cannot be undone. - Do not switch off the tumble dryer You can use the Miele App to check during an update. Otherwise, the the status of your tumble dryer from update will be aborted and will not be anywhere and start it remotely. -
Page 70: Smartgrid (Only Functional In Selected Countries)
Programmable functions The tumble dryer will then start within protected by copyright. The copyright the specified timeframe when it powers of Miele and third parties must receives your signal. be respected. If it has not received a start signal by the... - Page 71 Miele New Zealand Limited IRD 98 463 631 8 College Hill Freemans Bay Auckland 1011 New Zealand Telephone: 0800 4 MIELE (0800 464 353) www.miele.com.au/professional professional.sales@miele.com.au Miele Global Headquarters: Miele & Cie. KG Carl-Miele-Straße 29, 33332 Gütersloh, Germany...
- Page 72 PDR 1108 HP SmartBiz en-AU, NZ M.-Nr. 12 549 420 / 01...
Need help?
Do you have a question about the SmartBiz PDR 1108 HP and is the answer not in the manual?
Questions and answers