Page 2
Read this manual carefully before use, and retain it for future reference. Make sure to observe the following safety precautions to reduce the risks of errors, electric shocks, injuries, fires, deaths, and damage to equipment or property. Precautions • Be careful when trimming for the first time. Move the clipper smoothly and gently, rather than rapidly.
Page 3
• This appliance can be used by children aged from 8 years and above and persons with reduced physical, sensory or mental capabilities or lack of experience and knowledge if they have been given supervision or instruction concerning use of the appliance in a safe way and understand the hazards involved.
Charging Cleaning Power Sponge Barber Comb Cable Brush Adapter Cape Note: Illustrations of product and accessories in the user manual are for reference purposes only. Actual product and functions may vary due to product enhancements. Assembly & Disassembly Removing the blade head Turn off the clipper.
Page 6
get stuck, so please replace it as soon as possible. • Before removing the blade head, be sure to power off the clipper. If the blade head is hot, remove it after it cools off. Attaching the blade head 1. Turn the adjustable head dial to 1.7 mm. 2.
Removing the adjustable comb As shown in the figure, hold the top of the adjustable comb and pull it upwards to remove it. How to Use Charging • Before charging, be sure to turn off the clipper. • Plug the charging cable into the Type-C charging port and turn on the power supply to start charging.
Page 8
Using the standby button Operation Clipper status Turning on/off Press (resumes the previous mode by default) Press and hold for 2 Switching between low and high speed seconds upon turn-on modes Instructions on the travel lock • To enable the travel lock: While the clipper is turned off, press and hold the standby button for 3 seconds until the travel lock indicator blinks for 3 seconds and goes off, indicating the travel lock is enabled.
Page 9
Using the adjustable comb • Use the comb to brush the hair in the direction of the hair growth. • Choose a suitable adjustable comb and attach it to the clipper. • As shown in the image, slide the comb adjuster up and down to change the trimming length.
Page 10
Move the clipper against the direction of hair growth Go over multiple times with different lengths Notes • Using an adjustable comb helps prevent trimming hair too short by accident and control the overall length of the hairstyle. • Since hair tends to grow in different directions, the clipper must be moved in different directions (upwards/downwards/across) to keep it going against the direction of hair growth.
Page 11
Push the adjustable comb with your thumb to remove it Instructions on the blade head • When trimming the contours of the neck and sideburns, there's no need to use the adjustable comb. Instead, adjust the trimming length of the hair via the adjustable head dial. •...
Care & Maintenance Warning: Before cleaning and maintenance, the charging cable must be unplugged and the clipper must be turned off. Cleaning the blade head and clipper body 1. Remove the blade head. 2. Use the cleaning brush to remove any hair from the blade head. 3.
Environmental Protection When the clipper reaches the end of its service life, please remove, dispose of and recycle the built-in battery according to local laws and regulations of the country or region where the clipper is used. If the battery cannot be removed, dispose of the clipper in strict accordance with the regulations on classified domestic waste disposal in your area.
Note: If the battery has leaked and you accidentally touch it, rinse the area with plenty of water and seek medical attention immediately. Troubleshooting Issues Possible Causes Solutions The adjustable The adjustable comb is Reinstall the adjustable comb is wobbly. not properly installed.
Issues Possible Causes Solutions Check if the blade head Battery level is installed properly and Motor jam protection indicator displays if there is any foreign object in the clipper. Battery level Battery overheat indicator displays Check if the charging protection environment is abnormal (please charge at 5°C to Battery level...
Power Adapter lnput: 100–240 V~, 50/60 Hz, 0.2 Output: 5.0 V = 1.0 A, 5.0 W lnformation Published Value and Precision Unit Manufacturer's Name — Jiangxi Jian Aohai Technology Co., Ltd. Model ldentifier A520-050100U-EU1 — lnput Voltage 100–240 Input AC Frequency 50/60 Output Voltage Output Current...
Please contact the installer or local authorities for more information about the location as well as terms and conditions of such collection points. Manufactured for: Xiaomi Communications Co., Ltd. Manufactured by: Ningbo Lofans Home Appliance Co., Ltd. (a Mi Ecosystem company) Address: Room 22-3, Langmu Building, Baisha Road, Cixi City, Zhejiang, China For further information, please go to www.mi.com...
Need help?
Do you have a question about the mi Hair Clipper 2 and is the answer not in the manual?
Questions and answers