Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for Onfloor OF30 PRO
Summary of Contents for Onfloor OF30 PRO
- Page 1 OPERATION MANUAL & PARTS LIST OF30 PRO Multi-Purpose Floor Machine SAVE THESE INSTRUCTIONS Address: 777 South Street, Newburgh, NY 12550-0606 1365 N. 108th E. Ave, Tulsa, OK 74116 TEL: 877.356.6703 / 845.565.6623 Internet Address: www.onfloor.com info@onfloor.com...
-
Page 2: Table Of Contents
Installation Using a Press Installation without a Press Pulley Bearing Replacement Installation Using a Press Installation without a Press Troubleshooting Guide VFD Fault Codes Warranty Information Spare Parts and Accessories OF30 PRO Manual - Rev 1.0 - Printed in USA – 08/29/2024... -
Page 3: Specifications
Tool Speed 0-1350 RPM Variable Cutting Width 30” Vacuum Port 2” Minimum CFM for vacuum Weight 550 LBS Grinding Pressure 480 LBS Optional Weight 50 LBS (4 max) OF30 PRO Manual - Rev 1.0 - Printed in USA – 08/29/2024... -
Page 4: Before First Use
Treat this floor machine as you would any other high-grade precision-made product. Throwing, dropping, unreasonable bumping across thresholds and other misuse may result in a damaged unit and invalidate the warranty. OF30 PRO Manual - Rev 1.0 - Printed in USA – 08/29/2024... -
Page 5: Silica Vacuum Warning
Onfloor equipment. To achieve a high level of dust collection, use an industrial HEPA vacuum cleaner. OF30 PRO Manual - Rev 1.0 - Printed in USA – 08/29/2024... -
Page 6: Important Safety Instructions
These symptoms normally appear in the fingers, hands or wrists. These symptoms may be increased in cold temperatures. OF30 PRO Manual - Rev 1.0 - Printed in USA – 08/29/2024... -
Page 7: General Safety Precautions
Check the power cord for any breaks in the wire. Breaks will most likely occur near the plug or switch. Repair or replace any breaks immediately. Remove dust cover and vacuum out dust and debris from inner bowl. OF30 PRO Manual - Rev 1.0 - Printed in USA – 08/29/2024... -
Page 8: Transport And Storage
floor and lock. The machine may now be pushed and steered using the handle while the machine is rolled on its two tires and caster wheel. OF30 PRO Manual - Rev 1.0 - Printed in USA – 08/29/2024... -
Page 9: Grounding Instructions
Inadequate main power supply (less than 220 volts) ● Using light duty power cord ● Using more than 60 ft long power cord ● Operating from a generator ● OF30 PRO Manual - Rev 1.0 - Printed in USA – 08/29/2024... -
Page 10: Operating Instructions
Stand on the Tilt Assist Bar and grasp the handle grip with both hands. Lean back slightly and the machine will tilt backward. Guide the machine slowly to the floor using the handle. Lower until the machine rests on the caster. OF30 PRO Manual - Rev 1.0 - Printed in USA – 08/29/2024... -
Page 11: Adjusting The Dust Skirt
This switch serves to both start the motor and stop the motor. The red STOP portion is raised higher than the green START portion and is used as an emergency stop by slamming the button in an emergency. OF30 PRO Manual - Rev 1.0 - Printed in USA – 08/29/2024... - Page 12 Reverse Mode below in step 3) and the desire is to return to Forward, push the green start button again while the motor is running. Figure 3. Tool rotation direction OF30 PRO Manual - Rev 1.0 - Printed in USA – 08/29/2024...
-
Page 13: Speed Control
During operation the handle arm is positioned straight back and away from the motor. For storage and transport the handle arm is lowered forward over the top of the motor. OF30 PRO Manual - Rev 1.0 - Printed in USA – 08/29/2024... -
Page 14: Handle Grip Adjustment
7) Handle Grip Adjustment The handle grip can be positioned in any of 360 degrees location. This is sometimes desirable when operating the machines for long periods. OF30 PRO Manual - Rev 1.0 - Printed in USA – 08/29/2024... - Page 15 (see Figure 6). Use a 3/16” hex wrench to loosen but not remove the 4 screws. Rotate the handle to the desired angle and retighten the 4 screws securely. Figure 7. Handle grip screws OF30 PRO Manual - Rev 1.0 - Printed in USA – 08/29/2024...
-
Page 16: Dustless Performance
Dustless Performance Hook up the vacuum hose to the 2” vacuum port for dustless performance as shown in Figure 4. Figure 8. Vacuum port position OF30 PRO Manual - Rev 1.0 - Printed in USA – 08/29/2024... -
Page 17: Installation & Changing Of Accessory Tools
Using the handle, tilt the machine sideways until the handle is resting on the floor to one side. Remove tools from the machine. Remove the (9) ¼”-20 hex bolts and lock washers from the perimeter of the cover plate. Remove plate from machine. OF30 PRO Manual - Rev 1.0 - Printed in USA – 08/29/2024... -
Page 18: Inner Bowl Bearing Replacement
When using this method, it is important to properly support the cast aluminum bowl so as to prevent cracking the casting. This is OF30 PRO Manual - Rev 1.0 - Printed in USA – 08/29/2024... - Page 19 Followed by the spacer ring ( don't forget this). Finally, the last bearing. When properly installed the last bearing will be below the retaining ring groove and the retaining ring should go in easily. OF30 PRO Manual - Rev 1.0 - Printed in USA – 08/29/2024...
-
Page 20: Installation Without A Press
Turn the bowl over and rest its center on a short block of 4 x 4 lumber. (See Figure 10b). Figure 10b. Install new bearings in the inner bowl without a press. OF30 PRO Manual - Rev 1.0 - Printed in USA – 08/29/2024... -
Page 21: Pulley Bearing Replacement
With the pulley removed, we can proceed with bearing replacement. Look at the pulley from the back and you will see the retaining ring that secures the bearings in place. Wearing your safety glasses and using the retaining ring pliers remove the retaining ring. OF30 PRO Manual - Rev 1.0 - Printed in USA – 08/29/2024... -
Page 22: Installation Using A Press
OUTER RACE. It is important that you do NOT press on the inner race or seal to install the bearings. This will damage the bearings and shorten their life OF30 PRO Manual - Rev 1.0 - Printed in USA – 08/29/2024... -
Page 23: Installation Without A Press
Installation without a Press When using this method, Use a short piece of wood (or 15/16” socket) and a mallet/hammer to drive the old bearings from the pulley. See Figure 11b. OF30 PRO Manual - Rev 1.0 - Printed in USA – 08/29/2024... - Page 24 Turn the pulley over and rest its front face (or drive pins if present) on the piece of wood. Place the first bearing in the center opening and place a flat piece of wood or steel across the top of the bearing. See Figure 12b. OF30 PRO Manual - Rev 1.0 - Printed in USA – 08/29/2024...
- Page 25 (don't forget this) then; repeat the same process with the top bearing. Then install the retaining ring. Reinstall drive pins, pulley, belts, keeper plates, dust cover in reverse order of removal. OF30 PRO Manual - Rev 1.0 - Printed in USA – 08/29/2024...
-
Page 26: Troubleshooting Guide
Attachment is not level or securely attached. Possible Solution: Level attachment and make sure all fasteners are secure. 2) Possible Cause: Defective motor. Possible Solution: Contact the manufacturer or authorized service center. OF30 PRO Manual - Rev 1.0 - Printed in USA – 08/29/2024... -
Page 27: Vfd Fault Codes
If a fault code occurs, correct source of fault and restart machine. (Note: if power is removed from machine wait 2 minutes before restoring power.) OF30 PRO Manual - Rev 1.0 - Printed in USA – 08/29/2024... -
Page 28: Warranty Information
This Warranty is limited to repair or replacement of covered components and reasonable labor expenses. OF30 PRO Manual - Rev 1.0 - Printed in USA – 08/29/2024... -
Page 29: Spare Parts And Accessories
This Low Pulley with bearings fits the OF30 Pro heavy-duty machines. This pulley has a profile of LOW PULLEY CLOSEST TO THE 297615 HTD 1.5mm and has 18 teeth. The inside diameter INNER BOWL is 3/8''. OF30 PRO Manual - Rev 1.0 - Printed in USA – 08/29/2024... - Page 30 Using other traditional gel drive systems could probably damage your OF30 series machine, and it will definitely give a low output while using them on your concrete floor. OF30 PRO Manual - Rev 1.0 - Printed in USA – 08/29/2024...
Need help?
Do you have a question about the OF30 PRO and is the answer not in the manual?
Questions and answers