Sealey SDL7.V3 Manual

Thank you for purchasing a Sealey product. Manufactured to a high standard, this product will, if used according to these instructions,
and properly maintained, give you years of trouble free performance.
IMPORTANT: PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS, WARNINGS & CAUTIONS. USE
THE PRODUCT CORRECTLY AND WITH CARE FOR THE PURPOSE FOR WHICH IT IS INTENDED. FAILURE TO DO SO MAY CAUSE DAMAGE AND/OR
PERSONAL INJURY AND WILL INVALIDATE THE WARRANTY. KEEP THESE INSTRUCTIONS SAFE FOR FUTURE USE.
Refer to Hot surfaces
instructions
1. SAFETY
1.1. GENERAL SAFETY
WARNING! Ensure Health & Safety, local authority, and general workshop practise regulations are adhered to when using this equipment.
‰
Familiarise yourself with the application, limitations and potential hazards of the soldering station.
9
WARNING! This tool must be placed on its stand when not in use.
‰
Visually inspect the soldering iron before use. DO NOT use if damaged.
9
Replace or repair damaged parts. Use genuine parts only. Unauthorised parts may be dangerous and will invalidate the warranty.
9
Locate soldering station in a suitable working area, keep area clean and tidy and free from unrelated materials.
9
Keep the work area clean, uncluttered and ensure there is adequate lighting.
9
Keep the soldering iron clean for best and safest performance.
9
Ensure there are no flammable or combustible materials near the work area.
9
Wear appropriate protective clothing, including approved safety eye protection (standard spectacles are not adequate).
9
Ensure the workpiece is adequately held before operating the soldering iron. See Sealey model number SD150 (Mini Robot Soldering
9
Stand with Magnifier).
Always replace the soldering iron in its holder when not in use. Dismantle when out of service.
9
Remove excess solder from the soldering iron by wiping the tip on a damp, natural sponge; not by abrupt force.
9
DO NOT attempt to remove excess solder from the soldering iron by shaking it. Hot solder may become airborne and land on skin causing
8
burns and blisters.
DO NOT allow children or pets into the area where the soldering is taking place.
8
DO NOT attempt to cool the gun with water.
8
This appliance can be used by children aged from 8 years and above and persons with reduced physical, sensory or mental
9
capabilities or lack of experience and knowledge if they have been given supervision or instruction concerning use of the appliance in a
safe way and understand the hazards involved. Children shall NOT play with the appliance. Cleaning and user maintenance shall NOT
be carried out by children without supervision.
The appliance shall be disconnected from its power source during service and when replacing parts and, if that the removal of the plug
9
is foreseen, it shall be clearly indicated that the removal of the plug has to be such that an operator can check from any of the points to
which he has access that the plug remains removed.
1.2. BATTERY SAFETY
WARNING! For the purposes of recharging the battery, only use the detachable supply unit provided with this appliance
‰
WARNING! To reduce the risk of burns or fire:
‰
DO NOT attempt to open, disassemble, modify or service the battery pack.
8
DO NOT crush, puncture, short external contacts or dispose of in fire or water.
8
DO NOT expose to temperatures above 60°C (140°F).
8
Recycle or dispose of used equipment as stipulated by local regulation.
9
The battery must be removed from the appliance before it is scrapped.
9
The appliance must be disconnected from the supply mains when removing the battery.
9
The battery is to be disposed of safely
9
The appliance contains batteries that are only replaceable by skilled persons.
9
1.3. ELECTRICAL SAFETY FOR USE OF CHARGER
WARNING! Use only the supplied charger plug and for the purposes of recharging the battery, only use the detachable supply unit
‰
provided with this appliance.
WARNING! It is the user's responsibility to read, understand and comply with the following electrical instructions:
‰
The appliance must only be supplied at a safety extra low voltage corresponding to the marking on the appliance.
9
Only use the power supply unit provided with the appliance.
9
You must ensure the risk of electric shock is minimised by the installation of appropriate safety devices.
An RCCB (Residual Current Circuit Breaker) should be incorporated in the main distribution board. We also recommend that an RCD
(Residual Current Device, Sealey model RCD981) is used with all electrical products, particularly portable equipment which is
plugged into an electrical supply not protected by an RCCB.
You must also read and understand the following instructions concerning electrical safety.
1.3.1. The Electricity At Work Act 1989 requires all portable electrical appliances, if used on business premises, to be tested by a qualified
electrician, using a Portable Appliance Tester (PAT), at least once a year.
1.3.2. The Health & Safety at Work Act 1974 makes owners of electrical appliances responsible for the safe condition of the appliance and
© Jack Sealey Limited
8W RECHARGEABLE LITHIUM-ION
SOLDERING IRON
SDL7.V3
MODEL NO:
Indoor use Warning
only
Original Language Version
Wear eye
protection
SDL7.V3 Issue 1 18/03/24