Advertisement
Product Diagram
What's in the Box?
1 x Baby Night Light
1 x Carabiner
1 x Metal Plate with Tape
1 x USB Charging Cable
1 x User Manual
Specifications
| Product Name | NexiGo Nebula Night Light |
| Model | LT21 |
| Luminous Flux | 180 Lumens (Max) |
| Power Consumption | 2W |
| Power Input | DC 5V/1A |
| Color Temperature | 3000K/6500K & RGB |
| Battery Capacity | 2200mAh |
| Charging Time | 3.5 Hours |
| Working Time | 5 Hours (Brightest Setting), 118 Hours (Dimmest Setting), 400 Hours (Night Light Mode) |
| Dimensions | 3.74 x 3.74 x 3.54 Inches |
Usage Instructions
Power On/Off
Press and hold the Multi-Function Button on the bottom of the unit for 1.5 seconds to power on/off the light. When the light is switched on, the Indicator Light displays steady blue (or slowly flashes red when the battery is below 20%).
Turn On/Off
After the light is powered on, double-tapping the Touch Control Point to turn on/off the light.
Switch Light Mode
Press the Multi-Function Button to change the Light Mode of the lamp. The four possible modes are White Light Warm, White Light Cool, Cycling RGB and Rainbow RGB.
Night Light Mode
Turn On:
First, double tap the Touch Control Point to turn the light off.
When the light is off but powered on, press and hold the Touch Control Point to turn on the night light.
Turn Off:
Double tap the Touch Control Point to turn off the night light.
Adjust the Light Brightness
(Available in White Light Warm, White Light Cool and Night Light Mode)
Press and hold the Touch Control Point to adjust the brightness. When you press and hold the Touch Control Point, the light will alternate between increasing brightness or dimming. Once it reaches maximum brightness or minimum dimness it will remain at that settng. Pressing and holding the Touch Control Point again will cause it to reverse.
Note: The Indicator Light will flash green once when the brightness reaches the maximum or minimum level.
Adjust the RGB Light Changing Speed
(Available in Cycling RGB and Rainbow RGB Mode)
Tap the Touch Control Point to pause RGB/rainbow colors, taping again to continue the RGB light cycling. Press and hold the Touch Control Point to increase or decrease the speed that the lamp will cycle through the colors.
Note: The Indicator Light will flash green once when the speed reaches the maximum or minimum level
Low Battery Alert
The Indicator Light will slowly flash red when the battery is below 20%. Please charge the light by connecting it to a power source (Laptop, computer, etc. / Output: DC 5V/1A) using the provided USB charging cable.
Micro USB Charging
The Indicator Light will flash red while the light is charging and turn blue when the light is fully charged. For safety reasons, please unplug the adapter after the light is fully charged.
Using the Magnetic Light Mounts
The light can directly attach to many metal surfaces via the magnetic base. For convenient mounting on other surfaces, a Metal Plate with Tape is included.
- Clean the surface (such as a wall) where you want to place the light. (Sticker may remove paint. Use with care.)
- Peel the backing from the tape side of the metal plate and apply the metal plate to the surface where you want to place the light.
- Press and hold firmly for 30 seconds to secure the metal plate to whatever you are mounting it to.
- After the metal plate is attached, please wait about an hour to make sure the metal plate is firmly attached.
- Place the light's magnetic base against the metal plate so that it magnetically attaches.
Light Memory Function
The light will retain brightness and color settings between uses.
Notes:
- ONLY use a DC 5V/1A adapter with the provided USB cable to charge the unit. Using any other power adapter or cable may cause damage to the product.
- When this unit is not in use or when fully charged, it is recommended that you unplug it from the power source.
- Please use a lint-free dry cloth to clean the product. Do not clean the product with water or alcohol. Ensure the unit is unplugged and powered off before cleaning.
- Do not charge the light using a frayed or damaged USB cable.
- Do not touch the device, power adaptor, or USB cable with wet hands. Keep this product dry.
- Do not attempt to repair, disassemble, or modify the light under any circumstance.
- Do not place the light near the fire, heat sources, or direct sunlight.
- Ensure that this product has enough ventilation for general use.
- Only use on a flat, horizontal surface.
- To ensure the longevity and lifespan of the unit, protect it from dust and do not place other objects on it.
Contact Information
Tel: +1(458) 215-6088
Website: www.nexigo.com
If you have any problems please contact us at cs@nexigo.com at any time for further assistance.
Register to get an EXTRA ONE year warranty. Only valid if registering within 14 days of product delivery.
nexigo.com/warranty
Get in touch with FREE online services
facebook.com/nexigo1
Documents / Resources
References
Download manual
Here you can download full pdf version of manual, it may contain additional safety instructions, warranty information, FCC rules, etc.
Advertisement
Need help?
Do you have a question about the LT21 and is the answer not in the manual?
Questions and answers