Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for Protocol Insight FG4PSD2B
Summary of Contents for Protocol Insight FG4PSD2B
- Page 1 Protocol Insight® Solder-down Probe Quickstart Guide Covers: FG4PSD2B HS-G4B/HS-G3 x2 Bundle for Falcon B and Raptor FG4PSD3 HS-G4B/HS-G3 x2 optional Multi-Lead Pod Configuration for Falcon B and Raptor FG4PSD2 HS-G4B/HS-G3 x2 Bundle for original Falcon non-B instruments...
-
Page 2: Table Of Contents
Determining the best sampling points ...................... 5 Ground wire installation ..........................6 Connecting FG4PSD2B HS-G4B/HS-G3 x2 Bundle to the FalconB/Raptor ............ 6 Connecting the FG4PSD3 HS-G4B/HS-G3 x2 Multi-Lead Pod and the FG4PSD2 HS-G4B/HS-G3 x2 Bundle 7 Multi-lead pod – more configuration information ..................8... -
Page 3: Probe Overview
SSMP-to-SMA cables and a power supply. Compatibility The FG4PSD2B x2 Bundle is only compatible with the Falcon B and Raptor instruments, it is not compatible with the original Falcon non-B instruments. The optional FG4PSD3 Multi-Lead Pod x2 Configuration is intended for use with the Falcon B and Raptor instruments and the FG4PSD2B x2 Bundle. -
Page 4: Components
FG4PSD07 x1 pigtail cable with power connector FG4PSD05 HS-G4B Coax Multi-lead Probe Tip (6 inch) Product specifications and descriptions in this document are subject to change without notice. © Protocol Insight, LLC 2017, 2018, 2019 Revision 1.3.2, January 7, 2019 P a g e... - Page 5 FG4PSD04 Carlisle cable FG4PSD06 and FG4PSD08 phase matched SSMP-to-SMA and SSMP-to-SMP cable pairs Product specifications and descriptions in this document are subject to change without notice. © Protocol Insight, LLC 2017, 2018, 2019 Revision 1.3.2, January 7, 2019 P a g e...
-
Page 6: Preparing Probe Tips For Installation
The two leads must be cut to the length of +/- 0.01 inches. Product specifications and descriptions in this document are subject to change without notice. © Protocol Insight, LLC 2017, 2018, 2019 Revision 1.3.2, January 7, 2019 P a g e... -
Page 7: Determining The Best Sampling Points
M-PHY channel. As a general rule of thumb, this location is typically as near as possible to the Tx component pins (see illustration below). Product specifications and descriptions in this document are subject to change without notice. © Protocol Insight, LLC 2017, 2018, 2019 Revision 1.3.2, January 7, 2019 P a g e... -
Page 8: Ground Wire Installation
Use the short wire as much as possible to reduce the GND loop inductance. Connecting FG4PSD2B HS-G4B/HS-G3 x2 Bundle to the FalconB/Raptor After the tips have been soldered to the signals of interest on the DUT, the tips should then be connected to the instrument. -
Page 9: Connecting The Fg4Psd3 Hs-G4B/Hs-G3 X2 Multi-Lead Pod And The Fg4Psd2 Hs-G4B/Hs-G3 X2 Bundle
Lane 0 in the pod and so on. For more information, see – ULTI LEAD POD more . Product specifications and descriptions in this document are subject to change without notice. © Protocol Insight, LLC 2017, 2018, 2019 Revision 1.3.2, January 7, 2019 P a g e... -
Page 10: Multi-Lead Pod - More Configuration Information
Analyzer Sublink 0 Lane 0 and Lane 1 and Sublink 1 Lane 0 and Lane 1 to the corresponding connectors on the Analyzer. Product specifications and descriptions in this document are subject to change without notice. © Protocol Insight, LLC 2017, 2018, 2019 Revision 1.3.2, January 7, 2019 P a g e... -
Page 11: Contact Information
Protocol Insight representative or sales@protocolinsight.com Support materials and examples files are available at www.protocolinsight.com/support For technical support please contact your local Protocol Insight representative or support@protocolinsight.com Product specifications and descriptions in this document are subject to change without notice.
Need help?
Do you have a question about the FG4PSD2B and is the answer not in the manual?
Questions and answers