Important Safety Instructions This product is a professional photographic equipment, to be operated by professional personnel only. All transport protective materials and packaging on the product must be removed before use. The following basic safety precautions must be followed when using this product: Carefully read and fully understand the instruction manual before use and strictly follow the safety instructions.
Page 10
immediately if discomfort occurs, stop using, and seek medical attention promptly. If the flash tube is damaged, stop using it immediately and contact the manufacturer, service agent, or qualified repair personnel for a replacement to prevent accidents. Dot not use damaged equipment or accessories. Allow professional repair technicians to inspect and confirm normal operation before continuing use after repairs.
Page 11
personnel. Before storing the device, ensure it has completely cooled down and the power cord is unplugged, then put it in the protective case or a ventilated dry location. Do not place the device near alcohol, gasoline, or other flammable volatile solvents or gases such as methane and ethane.
Page 12
The warranty period for this device as a whole is one year. Consumables (such as batteries), adapters, power cords, and other accessories are not covered by the warranty. Unauthorized repairs will void the warranty and will incur charges. Failures from improper operation is not covered under warranty. Foreword Thank you for purchasing! With a tiny and exquisitely palm-holding size, iM20 can be inserted into the...
What’s Inside Flash Body USB-C Charging Storage Bag Instruction ×1 Cable ×1 ×1 Manual ×1 Power Switch/Test Button Power On: Press and hold the button until the indicators turn on, the flash is switched on. Test: After powering on, the green light blinks to indicate that the flash is recycling, which cannot be tested.
Power – Button/Power + Button Press the power- button or power + button can adjust the flash power in 5 levels. Press the power- button and power + button at the same time can check the battery level. One grid of green light means one grid of battery level, full battery level is five grids, so please charge the device in time if it only has one grid of battery level.
Technical Data Model iM20 Built-in Lithium Battery 3.8V, 470mAh Input 0.5A Flash Time (at full power) ≈440 Charging Time Approx. 1h10min Recycle Time (at full power) ≈3s Flash Power Steps Working Environment Temperature -10℃ ~ +35℃ Sync Triggering Hot Shoe Dimension 1.54"×1.50"×1.16"...
Declaration of Conformity: GODOX Photo Equipment Co,Ltd. hereby declares that the This equipment are in compliance with the essential requirements and other relevant provisions of EU Directive 2014/35/EU. 2014/30/EU. They are allowed to be used in all EU member states. ...
Page 18
IC Warning This device complies with Industry Canada licence-exempt RSS standard(s). Operation is subject to the following two conditions: (1) This device may not cause interference, and (2) This device must accept any interference, including interference that may cause undesired operation of the device. Le présent appareil est conforme aux CNR d'Industrie Canada applicables aux appareils radio exempts de licence.
Warranty Dear customers, as this warranty card is an important certificate to apply for our maintenance service, please fill in the following form in coordination with the seller and safe-keep it. Thank you! Product Model Product Code Number Information Customer Name Contact Number Information...
Applicable Products Applicable ProductsThe document applies to the products listed on the Product Maintenance lnformation (see below for further information). Other products or accessories (e.g. promotional items,giveaways and additional accessories attached,etc.) are not included in this warranty scope. Warranty Period The warranty period of products and accessories isimplemented according to the relevant Product Maintenance Information.
Page 25
If maintenance service is needed, you can directly contact the product distributor or authorized service institutions. You can also contact the Godox after-sale service call and we will offer you service. When applying for maintenance service, you should provide valid warranty card. If you cannot provide valid warranty card, we...
Page 26
Once met these situations above, you should seek solutions from the related responsible parties and Godox assumes no responsibility. The damage caused by parts, accessories and software that beyond the warranty period or scope is not included in our maintenance scope. The normal discoloration, abrasion and consumption are not the breakage within the maintenance scope.
Page 27
Parts Battery the product to designated site Customer sends Electrical parts the product to e.g.battery charger, etc. designated site Flash tube, modeling Other lamp, lamp body, lamp Without warranty Items cover, locking device, package, etc. Godox After-sale Service Call +86-755-29609320(8062)
Need help?
Do you have a question about the iFlash iM20 and is the answer not in the manual?
Questions and answers