Wood-mizer Laser Sight Safety, Operation, Maintenance & Parts Manual
Wood-mizer Laser Sight Safety, Operation, Maintenance & Parts Manual

Wood-mizer Laser Sight Safety, Operation, Maintenance & Parts Manual

For lt 30s, lt 40s, lt 50s sawmills
Hide thumbs Also See for Laser Sight:

Advertisement

Quick Links

Laser Sight, Post 1997
Safety, Operation, Maintenance
LS, Laser Kit, 97+ Sawmill
USED WITH:
LT 30s (Built after 1997)
LT 40s (Built after 1997)
LT 50s (Built after 1997)
WARNING! Read and understand this
!
manual before using this machine.
& Parts Manual
Safety is our #1 concern!
March 1997
rev. A.00 - D.01
Form #899

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the Laser Sight and is the answer not in the manual?

Questions and answers

Subscribe to Our Youtube Channel

Summary of Contents for Wood-mizer Laser Sight

  • Page 1 Laser Sight, Post 1997 Safety, Operation, Maintenance & Parts Manual LS, Laser Kit, 97+ Sawmill rev. A.00 - D.01 Safety is our #1 concern! March 1997 Form #899 USED WITH: LT 30s (Built after 1997) LT 40s (Built after 1997)
  • Page 2 Active Patents assigned to Wood-Mizer, LLC Wood-Mizer, LLC has received patents that protect our inventions which are a result of a dedication to research, innovation, development, and design. Learn more at: woodmizer.com/patents ©2024 Wood-Mizer LLC Printed in the United States of America, all rights reserved. No part of this manual may be reproduced in any form by any...
  • Page 3: Table Of Contents

    Table of Contents Section-Page SECTION 1 LASER INSTALLATION Laser Installation..................1-1 Switch Installation.................. 1-2 SECTION 2 OPERATION & ALIGNMENT Laser Operation..................2-1 Laser Alignment..................2-1 SECTION 3 REPLACEMENT PARTS Laser Assembly..................3-1 Table of Contents WM doc 4/22/24...
  • Page 4: Section 1 Laser Installation

    Installation Laser Installation SECTION 1 LASER INSTALLATION Before installing the laser option, be aware that the laser beam can not be seen in direct sunlight. The laser option is best for indoor cutting applications. Laser Installation 1. Remove the four lower slide pad mounting nuts (inside of mast post).
  • Page 5: Switch Installation

    Installation Switch Installation 9. Make sure the wire routes inside the guard at the lower right hand corner. See Figure 1-4 10. Install the provided two EMT clamps to the sec- tion of laser assembly wire which routes along the side mounting plate (underneath the pulley guard).
  • Page 6: Section 2 Operation & Alignment

    Operation & Alignment Laser Operation SECTION 2 OPERATION & ALIGNMENT Laser Operation To turn on the laser, raise the laser toggle switch laser toggle switch to the ON position. To turn off the laser, lower the laser toggle switch to the OFF position. Laser Alignment 1.
  • Page 7 Operation & Alignment Laser Alignment If the laser beam is adjusted too high, it will not show against the Use tack to secure in place side of the cant. g. Place an object on top of the cant so that the laser will be visible above the cant.
  • Page 8: Section 3 Replacement Parts

    Replacement Parts Laser Assembly SECTION 3 REPLACEMENT PARTS Laser Assembly 3H0352D PART # DESCRIPTION COMMENTS QTY. 024193 BRACKET ASSEMBLY, 97 LASER Available in assemblies only. 015508 Hood, Laser Bracket F05011-11 Washer, 1/4” SAE Flat F05005-15 Bolt, 1/4-20 X 1/2” Hex Head 050500 Laser Kit, Replacement w/Power Supply 050367...
  • Page 9 Replacement Parts Laser Assembly PART # DESCRIPTION COMMENTS QTY. F05089-1 Tie Wrap, 1/4” x 6” P03027 Switch, Toggle P05251-1 Washer, 1/2” x 3/4” x 1/16” Nylon P02575 Boot, Toggle Switch 024151 Fuse Assembly 024150-1 Fuse, ATO 1A Dark Grey F05010-121 Nut, 5/16-18 Nylon Lock Jam F05011-16 Washer, 5/16”...

Table of Contents