Advertisement
CB40WASSC
Network bullet cameras
INSTALLATION GUIDE
Rev.100
Inim Electronics S.r.l.
ISO 9001 Quality Management
certified by BSI with certificate number FM530352
Via dei Lavoratori 10, Centobuchi
63076 Monteprandone (AP) - Italy
Tel. +39 0735 705007_Fax +39 0735 704912
info@inim.it
_www.inim.it
DCMIINE0CB40WASSC-100-20240507
Advertisement
Table of Contents
Related Manuals for INIM InVista CB40WASSC
Summary of Contents for INIM InVista CB40WASSC
- Page 1 CB40WASSC Network bullet cameras INSTALLATION GUIDE Rev.100 Inim Electronics S.r.l. ISO 9001 Quality Management certified by BSI with certificate number FM530352 Via dei Lavoratori 10, Centobuchi 63076 Monteprandone (AP) - Italy Tel. +39 0735 705007_Fax +39 0735 704912 info@inim.it _www.inim.it...
- Page 2 Waterproof Requirements Please waterproof cables in accordance with the following instructions. User shall assume all responsibility for device damage caused by water due to improper waterproof measures. NOTE! • Before you start, connect all the needed cables and cut off the copper wires for the cables that you don't use.
-
Page 3: Packing List
DC interface Plug 5. (Optional) After the waterproof treatment is completed, put the cables into a waterproof junction box (purchased separately). CAUTION! • The cable connector must not be exposed and must be kept away from water. • Restore and fasten the device after dismounting. •... -
Page 4: Cable Connection
Cable Connection The tail cable may vary with device model. The figure below is for illustrative purposes only. ① ② ③ ④ Power interface Network interface Audio interface Alarm input/output interface Mount Your Camera (Optional) Install Micro SD Card You need to install a Micro SD card if you want to save video on an on-board SD card. NOTE! •... -
Page 5: Wall Mount
Screw 2. Remove the card cover. 3. Insert the Micro SD card into the slot. Micro SD card slot 4. Replace the card cover and tighten the screws. Wall Mount Before installation, make sure the wall is strong enough to hold the device. 1. - Page 6 3. Mount the camera onto the wall and connect all cables. Lead the self-tapping screws through the guide holes in the base and fix them on the wall using a screwdriver. 4. Adjust the shooting angle. (1) Adjust the opening of the universal joint as needed. (2) Tighten the locknut.
-
Page 7: Access Your Camera
Access Your Camera Log in to the device’s Web interface to perform management or maintenance operations. 1. Open your browser, enter the device’s IP address (192.168.1.13 by default) in the address bar and then press Enter to open the login page. 2. - Page 8 Disclaimer and Safety Warnings Copyright Statement No part of this manual may be copied, reproduced, translated or distributed in any form or by any means without prior consent in writing from our company (referred to as us hereafter). The product described in this manual may contain proprietary software owned by our company and its possible licensors.
- Page 9 interruption, loss of business information, or any special, direct, indirect, incidental, consequential, pecuniary, coverage, exemplary, subsidiary losses, however caused and on any theory of liability, whether in contract, strict liability or tort (including negligence or otherwise) in any way out of the use of the product, even if our company has been advised of the possibility of such damages (other than as may be required by applicable law in cases involving personal injury, incidental or subsidiary damage).
- Page 10 Store or use the device in a proper environment that meets environmental requirements, including and not limited to, temperature, humidity, dust, corrosive gases, electromagnetic radiation, etc. Make sure the device is securely installed or placed on a flat surface to prevent falling. ...
- Page 11 Regulatory Compliance FCC Statements This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Caution: The user is cautioned that changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment.
Need help?
Do you have a question about the InVista CB40WASSC and is the answer not in the manual?
Questions and answers