Advertisement
Quick Links
Advertisement
Related Manuals for AddSecure NGP Redcare Classic and GSM Replacement
Summary of Contents for AddSecure NGP Redcare Classic and GSM Replacement
- Page 1 NGP Redcare Classic and GSM Replacement Installation Guide For a safer and smarter world...
- Page 2 Contents Introduction Establish a connection to the Connect Hub AP using Technical specifications the Search option on the NGP Advanced Extra unit menu 18 Safety notes How to increase or decrease the brightness of the Connect Mounting and wiring Hub LED NGP Advanced Extra and Connect installation at Troubleshooting...
- Page 3 Introduction www.AddSecure.com NGP Classic and GSM Replacement...
- Page 4 NGP Advanced Extra the NGP Advanced Extra signalling unit to the customer’s broadband router or the AddSecure network to an Alarm unit to the existing connector layout in using an Ethernet cable. It’s designed to network.
- Page 5 Power Blue Blue Blue ETH (Ethernet) Blue Blue Blue Wi-Fi Orange Orange Blue AddSecure Orange Orange Blue IoT Link Cloud Orange Green Blue PRESS Colour when first powered up CONFIGURE Power ETH WiFi...
- Page 6 USB power lead for Connect Hub Wifi frequency and power 2.4GHz - Maximum transmit power +20dBm* Band 56a - 896 MHz - Maximum transmit power AddSecure IoT frequency and power: +7dBm* Connect Device Size (LxWxH) Environmental class II...
- Page 7 Locate wiring, pipes and services first to avoid accidents. www.addsecure.com NGP Classic and GSM Replacement...
- Page 8 Mounting and wiring www.AddSecure.com NGP Classic and GSM Replacement...
- Page 9 NGP Advanced Extra inside the panel following the instructions in the NGP Advanced Extra guide. Attach the external mobile aerial to the NGP Advanced Extra unit and Diagram 2: Fixing the plug-in adaptor to the NGP Advanced Extra unit www.addsecure.com NGP Classic and GSM Replacement...
- Page 10 Use either the self-adhesive pads on the rear TO NGP or fix with screws using the ADVANCED EXTRA holes provided. Diagram 3: Removing the front fascia of the Connect unit and connecting it www.addsecure.com NGP Classic and GSM Replacement...
- Page 11 USB power cable between the Connect USB power cable Diagram 6: Connecting the Hub and the customer’s router and/or AddSecure NGP Connect Hub to a USB mains plug should be no longer the customer’s router than three metres. Plug in the second network cable Check the Connect Hub’s status LEDs.
- Page 12 Set-up and initial configuration www.AddSecure.com NGP Classic and GSM Replacement...
- Page 13 Press and hold PRESS AND HOLD ENTER KEY Notice – Eth/Connect Saved! Ethernet Hub Discovery Notice – Done! Press and hold Diagram 7: Configuring the CONFIGURATION NGP Advanced unit WILL APPEAR Hub Discovery Discovering... www.addsecure.com NGP Classic and GSM Replacement...
- Page 14 The Classic and GSM replacement kit should now be working correctly. Power ETH WiFi Addsecure Cloud You should now also be able to see IoT Link the status of the Connect Kit from the Diagram 8: Location of WPS...
- Page 15 Additional configuration www.AddSecure.com NGP Classic and GSM Replacement...
- Page 16 ETH LEDs turn purple. Then different configuration mode. the web server release the button. Contact the AddSecure technical after 20 minutes’ helpdesk +44 20 461 431 70 or your The Power LED will start flashing. inactivity. Regional Technical Manager, for the Now open the Wi-Fi settings on an default login details.
- Page 17 CONFIGURATION Using Wi-Fi between the NGP 2. Direct connection via ethernet cable Please contact the AddSecure Log in to the Connect Hub web server Connect Hub and the customer’s to a laptop from the NGP Connect Hub Technical helpdesk on +44 20 461 and go to Settings >...
- Page 18 Now select the SSID of the customer's Wi-Fi network, Connect device are in their default state . provide the password and save. Go to the system status page. You’ll see Connect Hub is now connected to the user Hub, as shown below: www.addsecure.com NGP Classic and GSM Replacement...
- Page 19 Connect SSID Completed Redcare_xxxx information card Press and hold Insert the Connect passcode from the Connect passcode supplied information card using the up/down Saved xxxxxxxx keys and pressing the enter button. Connnect passcode Saved 12345678 www.addsecure.com NGP Classic and GSM Replacement...
- Page 20 Connect to be placed in an area where a better signal can be obtained. For both Wifi and AddSecure IoT: -90 dBm and less: X is displayed -89 dBm to -80 dBm: One bar ...
- Page 21 Troubleshooting www.AddSecure.com NGP Classic and GSM Replacement...
- Page 22 The correct colours are Advanced Extra scrolling display will show: Make sure the Wi-Fi and AddSecure IoT Link LEDs are shown in the right-hand column of the table below. both blue in colour on the Connect Hub. If they’re orange, the Connect and Connect Hub aren’t paired.
- Page 23 No ports need to be forwarded in the incoming Configuration Inputs direction. The outgoing TCP connection connects to port 443 or 10443 on the AddSecure network, so you Press until would need to allow outgoing access to port 443 or 10443 if you block that by default.
- Page 24 NGP Classic and GSM Replacement...
- Page 25 EU) has been put in place to recycle use of this equipment. All responsibility products using the best available BT Supply Chain and liability in the use of AddSecure recovery and recycling techniques Darlington Road products are assumed by the user.
- Page 26 Phone: +44 20 461 431 70 Email: support.smartalarms.uk@AddSecure.com If there is a problem with the service and/or communicator the End Customer should contact the alarm installer. The alarm installer can contact AddSecure Helpdesk M-F 9 till 5. www.addsecure.com NGP Classic and GSM Replacement...
Need help?
Do you have a question about the NGP Redcare Classic and GSM Replacement and is the answer not in the manual?
Questions and answers