Advertisement
Quick Links
Advertisement
Related Manuals for Bosch SMS88MI01X
Summary of Contents for Bosch SMS88MI01X
- Page 1 Dishwasher SMS88MI01X en Instruction manual...
- Page 3 Table of contents e n I n s t r u c t i o n m a n u a l Intended use ....5 Utensils.
- Page 4 Operating the appliance ..31 Customer service ... .49 Programme data ....31 Installation and connection.
- Page 5 Intended use en Delivery Intended use Check the packaging and This appliance is intended dishwasher immediately for ■ I n t e n d e d u s e for use in the home and the damage caused in transit. home environment.
- Page 6 en Safety instructions If the power cord of this Install built-under or ■ ■ appliance is damaged, it integratable appliances only must be replaced with a under continuous worktops particular power cord. which have been screwed to To prevent injury, the power adjacent cupboards to cord may be purchased from ensure stability.
- Page 7 Safety instructions en Damage Warning Risk of injury! The appliance may be To prevent injuries, e.g. ■ ■ repaired and opened up by a caused by stumbling, open technician only. To do this, the dishwasher only briefly in disconnect the appliance order to load and unload the from the power supply.
- Page 8 en Safety instructions When opening and closing Warning ■ the door on an eye-level Risk of explosion! appliance, ensure that Do not add any solvents to the children do not become rinsing compartment. Danger of jammed or crushed between explosion! the appliance door and the cupboard door below.
- Page 9 Safety instructions en Childproof lock (door lock) * Open the door with activated The child-proof lock (door lock) child-proof lock (door lock) as D o o r l o c k protects children from potential follows: Press the catch of the hazards which the dishwasher child-proof lock to the right poses.
- Page 10 en Environmental protection Environmental Getting to know your protection appliance Both the packaging of new appliances Diagrams of the control panel and the t e c t i o n E n v i r o n m e n t a l p r o y o u r a p p l i a n c e G e t t i n g t o k n o w and the old appliances themselves...
- Page 11 Getting to know your appliance en Appliance interior Info button { The Info button { can be used to See Fig. ~ Page 2 I n f o b u t t o n display additional programme 1" Interior light * information.
- Page 12 en Getting to know your appliance Switching on the appliance for the first time When the dishwasher is switched on for Change the setting as follows: the first time, you are taken directly to Keep pressing button > )* until the the settings for switching on the required setting is displayed.
- Page 13 Getting to know your appliance en Settings The dishwasher has been preset with Make the setting with setting buttons certain settings for your convenience. + - X. You can change this factory setting. Press and hold the Info button { 8 for 3 seconds.
- Page 14 en Getting to know your appliance Setting Factory setting Infotext by pressing Info button { Timelight * While programme is running, status information is projected onto floor. Infolight * Light is projected to signal an active cleaning cycle. Start programme Eco 50°...
- Page 15 Water softening system/special salt en Adjusting the water softening Water softening system system / special salt The amount of salt dispensed can be set from 0 to 62°E. Salt is not required To ensure good rinsing results, the at the set value 0-8. s y s t e m / s p e c i a l s a W a t e r s o f t e n i n g dishwasher requires soft water, i.e.
- Page 16 en Water softening system/special salt Using special salt Using detergents with salt component As soon as the low salt indicator P is If combined detergents with a salt lit on the control panel or is requested s a l t c o m p o n e n t D e t e r g e n t w i t h a component are used, special salt can on the front display * ):, salt should...
- Page 17 Rinse aid en Close the lid. Rinse aid Lid “clicks” into position. Remove overflowed rinse aid with a As soon as the low rinse-aid indicator cloth. R i n s e a i d H is lit on the control panel or is This prevents excessive frothing requested on the front display * ):, during the next rinse cycle.
- Page 18 en Utensils Switching off rinse aid refill Utensils indicator Not suitable If the use of combined detergents with a U t e n s i l s rinse-aid component impairs the low Cutlery and utensils made of wood. rinse-aid indicator H on the control ■...
- Page 19 Utensils en Loading the dishwasher Utensils must not be placed Note: above the tablet collecting tray 1B. These may block the lid of the detergent Remove large food remnants. It dispenser and prevent it from opening is not necessary to prerinse utensils fully.
- Page 20 en Utensils Heavily soiled utensils (pans) You can take out the cutlery drawer. Tip: should be placed in the lower basket. The more powerful spray jet provides a better dishwashing result. Other examples, such as the best Tip: way of loading your dishwasher, can be found on our homepage.
- Page 21 Utensils en Chopstick basket* Etagere * *depending on the model The etagere and the space underneath C h o p s t i c k b a s k e t E t a g e r e can be used for small cups and glasses Chopsticks up to a length of 24 cm can or for larger items of cutlery, such as be placed in the chopstick basket.
- Page 22 en Utensils Folding spikes * Knife rack * * Depending on the features of your * Depending on the features of your F o l d i n g s p i k e s K n i f e r a c k dishwasher, the spikes can be folded dishwasher, the upper basket is fitted down.
- Page 23 Utensils en Baking sheet spray head * Unloading the dishwasher * depending on the features of your To prevent water from dripping off the y h e a d B a k i n g s h e e t s p r a dishwasher upper basket onto the utensils in the Large trays or grilles as well as large...
- Page 24 en Utensils Adjusting the height of the Arrange large plates up to a diameter of 31/34* cm in the lower basket 1j as basket * illustrated. * depending on the features of your i g h t o f t h e b a s k A d j u s t i n g t h e h e dishwasher If required, the height of the upper...
- Page 25 Detergent en Upper basket with side levers Detergent Pull out upper basket 12. You can use tablets as well as powder Hold the sides of the basket along D e t e r g e n t or liquid detergents for dishwashers, but the upper edge.
- Page 26 en Detergent Adding detergent If the utensils are only lightly Tip: soiled, slightly less than the indicated amount of detergent is usually If the detergent dispenser 9* is still adequate. closed, actuate locking bar 92 to Suitable detergents and care products open it.
- Page 27 Detergent en If you switch from combined Notes ■ If you want to add more utensils after detergents to solo detergents, ■ the programme has started, do not ensure that the water softening use the tablet collecting tray 1B as system and amount of rinse aid have a handle for the upper basket.
- Page 28 en Overview of programmes Overview of programmes The max. possible number of programmes is illustrated in this overview. The a m m e s O v e r v i e w o f p r o g r corresponding programmes and their arrangement can be found on the fascia. Type of utensils Type of soiling Programme Possible...
- Page 29 Overview of programmes en Type of utensils Type of soiling Programme Possible Programme sequence additional options sensitive utensils, ñ / ð cutlery, Clean 45° slightly adhesive, Extra dry temperature-sens Intermediate rinse fresh food remnants Shine and Dry Quick wash 45° itive plastic and Final rinse 55°...
- Page 30 en Additional functions Ï intensiveZone * Additional functions Perfect for a mixed load. You can wash i n t e n s i v e Z o n e very soiled pots and pans in the lower * Depending on the features of your i o n s A d d i t i o n a l f u n c t basket together with normally soiled...
- Page 31 Operating the appliance en AquaSensor * Operating the * depending on the features of your appliance A q u a S e n s o r dishwasher The Aqua sensor is an optical Programme data measuring device (light barrier) which p l i a n c e O p e r a t i n g t h e a p measures the turbidity of the rinsing...
- Page 32 en Operating the appliance Sensor setting AutoPowerOff (Switching off automatically after the end of The programme sequence is optmised the programme) in Auto programmes with the aid of sensors. The sensors adjust the To save energy, the dishwasher A u t o P o w e r O f f programme strength of Auto is switched off 1 minute after programmes depending on the amount...
- Page 33 Operating the appliance en TimeLight (Optical display Button volume while the programme is When you are operating the dishwasher, running) * a signal sounds whenever a button is pressed. You can control the volume of * depending on the features of your t i m e L i g h t the signal.
- Page 34 en Operating the appliance Switching the appliance on Time preselection You can delay the start of the Turn on tap fully. programme by up to 24 hours. Open the door. Depending on the setting of the time Switch on ON/OFF switch (. display, the end of programme is The Eco 50°...
- Page 35 Operating the appliance en Switching off the appliance Terminating the programme (Reset) Short time after the end of the Open the door. programme: p r o g r a m m e T e r m i n a t i n g t h e Press the START button )"...
- Page 36 en Cleaning and maintenance Regularly wipe the front Cleaning and of the appliance and fascia with a damp cloth; water and a little washing up maintenance liquid are adequate. Do not use sponges with a rough surface A regular inspection and maintenance or abrasive detergents, as these could t e n a n c e C l e a n i n g a n d m a i n...
- Page 37 Cleaning and maintenance en Filters Spray arms The filters 1Z keep large foreign Limescale and contaminants in the objects in the rinsing water away from rinsing water may block nozzles and the pump. hese foreign objects may bearings on the spray arms 1: and occasionally block the filters.
- Page 38 en Fault, what to do? Error message Fault, what to do? Some faults are indicated at the top of the display window @ and on the front Experience has shown that you can F a u l t , w h a t t o d rectify most faults which occur in daily display * ): and possible remedies are offered (for example Filter system...
- Page 39 Fault, what to do? en Clean the waste water pump as follows: Disconnect the dishwasher from the power supply. Take out top basket 12 and bottom basket 1j. Remove the filters 1Z. Scoop out water, use a sponge if required. Prise off the pump cover (as shown) using a spoon.
- Page 40 en Fault, what to do? Fault table Fault Cause Remedial action Error code “:‚‰ is lit. Supply hose kinked. Install supply hose without kinks. Tap turned off. Turn on the tap. Tap jammed or calcified. Turn on the tap. Flow rate must be min. 10 l/min. when water supply is open.
- Page 41 Fault, what to do? en Fault Cause Remedial action Error code “:ƒˆ is lit. Mains voltage too low. Not an appliance fault, have the mains voltage and electrical installation checked. A different error code is A technical fault has probably Switch off appliances with the ON/OFF indicated on the digital occurred.
- Page 42 en Fault, what to do? Fault Cause Remedial action Utensils not dry. No or too little rinse aid in the Refill rinse aid. dispenser. Programme selected without Select programme with drying. drying. ~ "Overview of programmes" on page 28 Water collecting in depressions Arrange utensils in a sloping position, on the utensils and cutlery.
- Page 43 Fault, what to do? en Fault Cause Remedial action Food remnants on the Utensils placed too closely Arrange utensils with adequate clearance utensils. together, utensils basket between them ensuring that the spray jets overfilled. can reach the surface of the utensils. Prevent contact points.
- Page 44 en Fault, what to do? Fault Cause Remedial action Detergent residue. Detergent dispenser cover 9* Utensils must not be placed above the blocked by utensils and therefore tablet collecting tray 1B. These may does not open fully. block the lid of the detergent dispenser and prevent it from opening fully.
- Page 45 Fault, what to do? en Fault Cause Remedial action White, stubborn coatings; Detergent substances are Change detergent brand. limescale on the utensils, deposited. These coatings cannot Clean appliance mechanically. container or door. usually be removed with chemicals (appliance cleaner, ...). Hardness range incorrectly set or Set water softening system according to water hardness greater than 8.9...
- Page 46 en Fault, what to do? Fault Cause Remedial action Plastic parts discoloured. Too low rinsing temperature. Select programme with higher washing temperature. Utensils precleaned too intensely; Do not prerinse utensils. Remove only sensors therefore decide on large food remnants. weak programme sequence. Increase sensitivity of the sensors.
- Page 47 Fault, what to do? en Fault Cause Remedial action Appliance cannot be Malfunction. Disconnect appliance from the power switched on or operated. supply; pull out the mains plug or switch off the fuse. Wait at least 5 seconds, then connect the appliance to the power supply.
- Page 48 en Fault, what to do? Fault Cause Remedial action Knocking or rattling noise. Spray arm strikes the utensils, Position utensils so that the spray arms do utensils not positioned correctly. not strike the utensils. If there is a low load, the water Load the appliance with more utensils or jets strike the washing tank distribute the utensils more evenly in the...
- Page 49 Customer service en Customer service Installation and connection If you are unable to rectify the fault, C u s t o m e r s e r v i c e please contact your customer service. The dishwasher must be connected We will always find an appropriate c o n n e c t i o n I n s t a l l a t i o n a n d...
- Page 50 en Installation and connection Delivery Installation Your dishwasher has been checked The required installation dimensions thoroughly in the factory to ensure that can be found in the installation it is in working order. This may cause instructions. Level the appliance with small water stains.
- Page 51 Installation and connection en Drinking water connection Warm water connection * * depending on the features of your Fasten the drinking water connection i o n W a r m w a t e r c o n n e c t dishwasher to the tap according The dishwasher can be connected...
- Page 52 en Installation and connection Electrical connection Transporting Empty the dishwasher and secure loose Connect the appliance only to 110 V ■ parts. and 50 Hz or 60 Hz alternating current via a correctly installed Drain the appliance according socket with protective conductor. to the following steps: See rating plate for required fusing Turn on the tap.
- Page 56 *9001081294* 9001081294 (9503) 642 TW...
Need help?
Do you have a question about the SMS88MI01X and is the answer not in the manual?
Questions and answers