Advertisement
Quick Links
Rail Installation Guide
ThinkSystem Toolless Stab-in Slide Rail Kit V3
This document provides important information about the ThinkSystem Toolless Stab-in Slide Rail Kit V3.
Rail kit parts inventory
Each slide rail kit package contains the following items:
Figure 1. Rail kit parts inventory
Note: Refer to the following for different types of rack hole supported.
ThinkSystem Toolless Stab-in Slide Rail Kit V3 supports:
Figure 2. Square-hole rack
Read these guidelines first
Read the following guidelines before installing the rail kit and system to the rack.
• The rail travel distance is 820 mm (32.28 inches).
• The maximum system weight that a rail kit supports is 34 kg (74.96 lb).
• Install the system to a rack that meets the following requirements:
– Minimum depth of 70 mm (2.76 inches) between the front mounting flanges and inside of the front door.
– Minimum depth of 214 mm (8.43 inches) between the chassis rear wall and inside of the rear door.
1
One left rail
2
One right rail
3
Two M6 screws
Note: If any part is missing, contact your local support.
Figure 3. Round-hole rack
1 1
Advertisement
Related Manuals for Lenovo ThinkSystem Toolless Stab-in Slide Rail Kit V3
Summary of Contents for Lenovo ThinkSystem Toolless Stab-in Slide Rail Kit V3
- Page 1 Rail Installation Guide ThinkSystem Toolless Stab-in Slide Rail Kit V3 This document provides important information about the ThinkSystem Toolless Stab-in Slide Rail Kit V3. Rail kit parts inventory Each slide rail kit package contains the following items: Figure 1. Rail kit parts inventory...
- Page 2 – Maximum distance between the front mounting flange and the rear mounting flange is 864 mm (34.00 inches). – If you want to install the rails and a 0U PDU into the same rack, the rack must meet the following height and depth requirements: - 42U or higher - At least 1000 mm (39.37 inches) deep if no CMA is to be installed...
- Page 3 Install the rail kit to the rack Note: The rails are extensible as shown in the following illustration. Figure 4. Extensible rails Step 1. Select the first rail that you want to install. Step 2. Make sure the rail is shortened to the shortest position. Step 3.
- Page 4 Rotate the rear latch back to the closed position. Step 5. Install the front mounting pins to the rack. Figure 6. Installing front mounting pins Slide the inner rail all the way in to allow the front latch to open. Open the front latch and align the mounting pins with corresponding front mounting flanges.
- Page 5 Install the server to rails Step 1. Remove the inner rails from the intermediate rails. Figure 7. Removing the inner rails Extend the inner rails. Push up the latches to disengage inner rails from the intermediate ones. Remove the inner rails. Step 2.
- Page 6 Make sure three people are lifting the sever by holding the lift points. Figure 9. Lifting up the server Step 5. Install the server to the rack. Align both rear ends of the inner rails with the openings in the intermediate rails, and make sure that the two pairs of rails mate correctly.
- Page 7 Figure 11. Locking latches Lift the lock latches on both sides. Push the server all the way into the rack until both latches lock into position with a click. Step 7. Secure the server to the rack. a. Secure the server to the front of the rack. Fasten the two screws located on the rack latches. Figure 12.
- Page 8 First Edition (November 2024) © Copyright Lenovo 2024. LIMITED AND RESTRICTED RIGHTS NOTICE: If data or software is delivered pursuant to a General Services Administration (GSA) contract, use, reproduction, or disclosure is subject to restrictions set forth in Contract No. GS-35F- 05925.
Need help?
Do you have a question about the ThinkSystem Toolless Stab-in Slide Rail Kit V3 and is the answer not in the manual?
Questions and answers