Advertisement
Quick Links
Advertisement
Related Manuals for Seeley Braemar ECO-SUPERSTAR SH18
Summary of Contents for Seeley Braemar ECO-SUPERSTAR SH18
- Page 1 INSTALLATION MANUAL SEELEY INTERNATIONAL BRAEMAR ECO-SUPERSTAR SH18, SH25 & WF25 HEATERS...
- Page 2 Compliance with these regulations will require appropriate work practices, equipment, training and qualification of workers. Seeley International provides the following information as a guide to contractors and employees to assist in minimising risk.
- Page 3 HEATER SPECIFICATIONS TECHNICAL SPECIFICATIONS Gas type SH18 SH25,WF25 Nominal gas input rate (MJ/h) Natural gas Propane Nominal thermal output (kW) Test point pressure (kPa) Natural gas - high 1.00 1.00 Natural gas - low 0.50 0.50 Propane - high 1.70 2.00 Propane - low 0.85...
- Page 4 PREPARATION AND CONNECTIONS UNPACKING THE HEATER Lay the carton flat on the floor and open. Remove the font cover from the heater (screws inside plastic louvre section / s). Check that the heater model and gas type are as required - model details are marked on the heater.
- Page 5 INBUILT HEATER INSTALLATION INSTALLATION PROCEDURE 1. Fit heater onto pre-installed mounting brackets. (refer relevant flue kit installation instructions.) 2. Lift heater to fit top retaining tabs into slots in top mounting bracket - make sure both sides are engaged. 3. Push bottom of heater into cavity and lower onto bottom mounting bracket - make sure that heater main body panel is located in the bottom mounting bracket at both sides.
- Page 6 CONSOLE HEATER INSTALLATION INSTALLATION PROCEDURE 1. Fit heater onto pre-installed mounting brackets. (refer relevant flue kit installation instructions.) 2. Lift heater to fit top retaining tabs into slots in top mounting bracket - make sure both sides are engaged. 3. Push bottom of heater into cavity and lower onto bottom mounting bracket - make sure that heater main body panel is located in the bottom mounting bracket at both sides.
- Page 7 FITTING FRONT COVER SH Fitting front cover Connect earth lead from heater cover to body of heater - top left of cover and heater body 2. Connect control loom (multi coloured ribbon cable) to main PCB on electrical mount panel - connection is labelled "FRONT PANEL".
- Page 8 COMMISSIONING COMMISSIONING PROCEDURE 1. CONNECT GAS AND ELECTRICITY - check gas type, purge gas line of air and debris 2. CHECK FOR GAS LEAKS - check for gas leaks as detailed in AS/NZS 5601 "Gas installations" - rectify any leaks found. 3.
- Page 9 FITTING FRONT COVER WF25 Fitting front cover 1. Secure cover bracket (640204) 1610mm from lower edge of heater mount bracket (634791) as shown 2. Connect earth lead from heater cover to body of heater - middle of cover and heater body 3.
- Page 10 FITTING FRONT COVER WF25 Wall Furnace replacement where the wall cut-out exceeds 1800mm. 1. Attach 2 brackets (640198) to top bracket (640204) as shown. 2a. Mark 1610mm from lower edge of bracket (634791) to the top of bracket (640204) (SEE PREVIOUS PAGE) 2b.
- Page 11 Orange and green indicator flashing - SERVICE RESET - access service mode. If a fault occurs refer to the labels on the inside of the front cover to identify the cause of the fault. If further assistance is required contact the Seeley International Service Department: Service:...
- Page 12 Warranty Service Australia 1-300-650-644 seeleyinternational.com It is the policy of Seeley International to introduce continual product improvement. Accordingly, speci cations are subject to change without notice. Please consult with your dealer to con rm the speci cations of the model selected.
Need help?
Do you have a question about the Braemar ECO-SUPERSTAR SH18 and is the answer not in the manual?
Questions and answers