Using The C 55Bee - Cd 8 Remote Control; Numeric Key Pad; Rpt A-B; Dimmer - NAD C545BEE Owner's Manual

OPERATION
uSing the c 545bee – cd 8 remote control
A wireless remote control is provided with your compact disc player,
enabling you to operate playback functions from the comfort of your chair
or from virtually anywhere in the room. For reliable operation there should
be a clear line-of-sight path from the remote control to the front of the CD
player. If the player does not respond to remote commands, it may be that
this line-of-sight path is obstructed by clothing, paper or furnishings.
Most of the buttons on the remote control handset have the same effect as
the corresponding buttons on the front panel of the player. In addition, the
handset is equipped with some extra buttons like the following function
keys.

NUMERIC KEY PAD

Using the direct-entry numeric keypad (0 to 9) causes the C 545BEE to jump
directly to the beginning of a numbered track and commence play. Thus, to
play Track 5, simply press "5". To play Track 20, press "2" and "0".

RPT A-B

To repeat a sequence, implement the following procedures:
1 Press [RPT A-B] at your chosen starting point.
2 Press [RPT A-B] again at your chosen end point. The repeat sequence
begins.
3 Press [RPT A-B] again to cancel the sequence.

REFERENCE

troubleShooting

condition
No power.
The power is ON, but the C 55BEE does
not work.
The C 55BEE does not start playback.
No sound.
Sound skips.
The remote control does not work properly.
1

DIMMER

Toggle to reduce, turn off and restore VFD brightness.

PROGRAM AND DELETE

Use [PROG] button to start, review, edit or exit programming mode. In
combination with [PROG] button, the [CLEAR] button allows the deletion of
a programmed track during program review or edit sequence.
the item about "PROGRAMMING" at the "USING THE C 545BEE – FEATURES"
section of the "OPERATION" page.

FILTER

The [FILTER] button is used for selecting the bandwidth of the audio low
pass filter for the CD, MP3 and WMA media being played. The options are
NORMAL Bandwidth and SLOW Bandwidth. For some recordings the SLOW
Bandwidth may provide a wide frequency range and spatial feeling. Toggle
CD 8's [FILTER] button to select "NORMAL" or "SLOW" mode. "NORMAL FILTER"
or "SLOW FILTER" will be correspondingly shown in the VFD.
normal: Select NORMAL bandwidth to engage a standard CD high-
pass filter slope for playback of CD, MP3, and WMA music through the
two channel stereo audio jacks.
Slow: Select SLOW bandwidth to engage a gentle high-pass filter
slope for playback of CD music through the two channel stereo audio
jacks. This feature is particularly useful for higher bit rate recordings.
poSSible cauSeS
• The power cord is disconnected.
• No disc is inserted.
• The disc is loaded upside down.
• The disc is too dirty.
• The equipment connected with the audio
cable is not set to receive CD signal output.
• The power of the equipment connected with
the audio cable is turned off.
• The C 545BEE is subject to vibration or physical
shock from external sources.
• The remote control is not pointed at the
remote sensor on the CD player.
• The remote control is too far from the CD
player.
• The remote control batteries are dead.
Refer also to
poSSible SolutionS
• Plug the power cord into the wall outlet
securely.
• Insert a disc.
• Reload the disc with the label side UP.
• Clean the disc.
• Select the correct input mode of the audio
receiver so you can listen to the sound from
the C 545BEE.
• Turn on the equipment connected with the
audio cable.
• Change the installation location.
• Point the remote control at the remote
sensor of the CD player.
• Operate the remote control closer to the
CD player.
• Replace the remote control batteries.