P-335 Firewall Router with Print Server P-335WT 802.11g Wireless Firewall Router with Print Server Quick Start Guide Version 3.60 9/2005 Table of Contents ENGLISH DEUTSCH ESPAÑOL FRANÇAIS ITALIANO 中文...
Page 2
P-335, P-335WT Quick Start Guide ENGLISH DEUTSCH ESPAÑOL FRANÇAIS ITALIANO 中文...
ENGLISH ENGLISH Overview The Prestige is a broadband router with a built-in four-port 10/100 Mbps switch. The Prestige makes it easy to set up a small home or office network and share Internet access via a broadband (cable/DSL) modem. Key features of the Prestige include a firewall, print server, VPN, content filtering, NAT and UPnP.
ENGLISH 1 Hardware Connections Do the following to make hardware connections for initial setup. WAN Connection Connect your modem to the “WAN” port using the cable that came with your modem. LAN Connection Connect your computer to a "LAN" port using the included Ethernet cable. USB Printer Port Connection Use a USB cable to connect a USB printer to this port.
The LEDs Look at the front panel LEDs. When you connect the power, the PWR and WLAN (P-335WT) LEDs come on. The LAN and WAN LEDs turn on if the corresponding connections are properly made. The USB LED turns on if a USB device is connected.
DHCP from the ISP is used. STEP 2: Wireless LAN (P-335WT) Configure ONE of the following wireless security types on the Prestige: • Auto security: Uses WPA-PSK security with an automatically generated Pre-Shared Key. View the generated Pre-Shared Key in the Wireless LAN screen.
Page 7
ENGLISH • None: Have no wireless LAN security configured. If you do not enable any wireless security on your Prestige, your network is accessible to any wireless networking device that is within range. • Basic security: WEP (Wired Equivalent Privacy) encrypts data frames before transmitting over the wireless net- work.
Page 8
ENGLISH Basic(WEP) Security A Enter a unique name to identify the Prestige in the wireless LAN. B Leave the default setting. The Prestige and wireless client must use the same channel ID. C Select Basic(WEP) security. D You can generate or manually enter a WEP key by either: Entering a Passphrase (up to 32 printable characters) and clicking Generate.
Page 9
ENGLISH Extend(WPA-PSK) or (WPA2-PSK) Security A Enter a unique name to identify the Prestige in the wireless LAN. B Leave the default setting. The Prestige and wireless client must use the same channel ID. C Select WPA-PSK or WPA2-PSK security. D Type a pre-shared key to have a more secure wireless connection than WEP encryption.
Page 11
ENGLISH STEP 3: The wizard attempts to detect which WAN connection type you are using. If the wizard does not detect a connection type, you must select ONE from the drop-down list box. Check with your ISP to make sure you use the correct type: 1 Ethernet 2 PPPoE 3 PPTP.
Page 12
ENGLISH Ethernet Connection A Select Ethernet as your WAN connection type. B Select Get automatically from your ISP if your ISP did not assign you a fixed IP address. Skip to D. Select Use fixed IP address provided by your ISP to give the Prestige a fixed, unique IP address. C Enter a WAN IP address and WAN IP Subnet Mask of the neighboring device, if you know it.
Page 13
ENGLISH PPPoE Connection A Select PPPoE as your WAN connection type. BType a Service Name (Optional), User Name and Password. C Select Get automatically from your ISP if your ISP did not assign you a fixed IP address. Skip to E. Or select Use fixed IP address provided by your ISP to give the Prestige a fixed, unique IP address.
Page 14
ENGLISH PPTP Connection A Select PPTP as your WAN connection type. BType a User Name and Password C Select Get automatically from ISP if your ISP did not assign you a fixed PPTP IP address. Or select Use fixed IP address to give the Prestige a fixed, unique PPTP IP address and subnet mask. D Type a PPTP Server IP Address E Type a Connection ID/Name (if provided) F Select Get automatically from your ISP if your ISP did not assign you a fixed IP address.
4 Bandwidth Management Wizard Click the Go to Bandwidth Management Wizard (optional) hyperlink or click the Bandwidth Management wizard option in the Welcome to the ZyXEL Wizard Setup screen. Bandwidth management allows you to control the amount of bandwidth going out through the Prestige’s WAN port and prioritize the distribution of...
ENGLISH STEP 1: General Information Select the Active check box. The Prestige does not control the bandwidth allocated to traffic that comes into an interface. Enter the amount of Managed Bandwidth in kbps (2 to 100,000) that you want to allocate for traffic. The recommendation is to set this speed to be equal to or less than the upstream speed of the cable/DSL modem connected to the WAN port of the Prestige.
ENGLISH STEP 3: Priority Setup Select High, Mid or Low priority to control the distribution of bandwidth to selected services. A service with High priority is given as much bandwidth as it needs. If you select services as having the same priority, then bandwidth is divided equally amongst those services.
Page 19
9 Close the Network Connections screen. Viewing Your Product’s Certifications 1 Go to www.zyxel.com. 2 Select your product from the drop-down list box on the ZyXEL home page to go to that product's page. 3 Select the certification you wish to view from this page.
DEUTSCH DEUTSCH Übersicht Der Prestige ist ein Breitband-Router mit einem integrierten 10/100 Mbps Schalter mit vier Anschlüssen. Mit dem Prestige können Sie ganz einfach ein kleines Heim- oder Büronetzwerk aufbauen und einen Internetzugang von mehreren Rechnern aus über ein Breitbandmodem (Kabel/DSL) nutzen. Die Leistungsmerkmale des Prestige schließen eine Firewall, Druckserver, VPN, Webinhaltfilterung, NAT und UPnP ein.
Page 21
DEUTSCH 1 Anschließen der Hardware Bei der Erstinstallation müssen die folgenden Hardwareverbindungen hergestellt werden. Herstellen der WAN-Verbindung Schließen Sie Ihr Modem mit dem mitgelieferten Kabel an den WAN-Anschluss an. Herstellen der LAN-Verbindung Schließen Sie Ihren Computer mit dem mitgelieferten Ethernet-Kabel an einen "LAN"-Anschluss an. Druckserver-Verbindung Verbinden Sie einen USB-Drucker über ein USB-Kabel mit diesem Anschluss.
Page 22
DEUTSCH Verbinden Sie den Netzanschluss des Geräts (POWER) mit dem mitgelieferten Netzadapter mit einer geeigneten Stromquelle (eine nach Regionen geordnete Liste der Netzadapter-Spezifikationen finden Sie im Benutzerhandbuch). Die LED-Anzeigen Die LED-Anzeigen befinden sich an der Gerätevorderseite. Sobald das Gerät mit Strom versorgt wird, beginnen die LED-Anzeigen PWR und WLAN (P- 335WT) zu leuchten.
Page 23
DEUTSCH Hinweis: Wenn das folgende Fenster nicht angezeigt werden sollte, gehen Sie zu Abschnitt 2 Auf dem Bildschirm erscheint das Fenster 4 Wenn Sie den Prestige das erste Mal benutzen, Passwort. Geben Sie das Passwort ein ("1234" klicken Sie auf Go Wizard setup (Zum ist das Standardpasswort) und klicken Sie auf Einrichtungsassistenten) und klicken Sie auf Apply Login (Anmelden).
Page 24
DHCP des Internetdienstanbieters vorgege- ben ist. SCHRITT 2: Wireless LAN (P-335WT) Konfigurieren Sie beim Prestige EINEN der folgenden Wireless-Sicherheitstypen: Auto security (Automatische Sicherheit): WPA-PSK-Sicherheit mit einem automatisch erzeugten Pre-Shared- Key. Sehen Sie sich den erzeugten Pre-Shared-Key im Fenster Wireless LAN an.
Page 25
DEUTSCH OTIST Mit der OTIST-Technologie (One-Touch Intelligent Security Technology) kann der Prestige den Wireless-Clients die eigenen Einstellungen für SSID und statische WEP oder WPA-PSK-Verschlüsselung zuweisen. Der Wire- less-Client muss ebenfalls OTIST unterstützen, und die OTIST-Funktion muss aktiviert sein. Automatisch oder Keine Wireless-Sicherheit A Geben Sie einen Namen ein, mit dem der Prestige im Wireless-Lan eindeutig identifiziert wird.
Page 26
DEUTSCH Basis-Sicherheit (WEP) A Geben Sie einen Namen ein, mit dem der Prestige im Wireless-Lan eindeutig identifiziert wird. B Belassen Sie die Standardeinstellung. Der Prestige und der Wireless-Client müssen dieselbe Kanal-ID verwenden. C Wählen Sie die Sicherheitsstufe Basic (WEP) (Basis (WEP)). D So können Sie einen WEP-Schlüssel erzeugen oder manuell eingeben: Geben Sie eine Passphrase (mit maximal 32 druckbaren Zeichen) ein und klicken Sie auf Generate (Erzeugen).
Page 27
DEUTSCH Erweitern (WPA-PSK) oder WPA2-PSK-Sicherheit. A Geben Sie einen Namen ein, mit dem der Prestige im Wireless-Lan eindeutig identifiziert wird. B Belassen Sie die Standardeinstellung. Der Prestige und der Wireless-Client müssen dieselbe Kanal-ID verwenden. C Wählen Sie die Sicherheit WPA-PSK oder WPA2-PSK. D Geben Sie einen Pre-Shared-Key ein, wenn die Wireless-Verbindung sicherer sein soll als mit einer WEP- Verschlüsselung.
Page 28
DEUTSCH SCHRITT 3: Der Assistent versucht zu ermitteln, welche Art von WAN-Verbindung Sie verwenden. Wenn der Assistent keinen Verbindungstyp erkennen kann, müssen Sie aus dem Listenfeld EINEN auswählen. Prüfen Sie bei Ihrem Internetdienstanbieter, ob Sie den richtigen Typ verwenden: 1 Ethernet...
Page 29
DEUTSCH 2 PPPoE 3 PPTP Hinweis: Wenn Ihnen Zugangseinstellungen für das Internet vorgegeben wurden, geben Sie diese in die folgenden Felder ein. Anderenfalls werden die Standardeinstellungen belassen. Klicken Sie auf Next (Weiter). Ethernet-Verbindung A Wählen Sie als Ihren WAN-Verbindungstyp Ethernet. B Wählen Sie Get automatically from your ISP (Automatisch vom Internetdienstanbieter laden), wenn Sie von Ihrem Internetdienstanbieter keine feste IP-Adresse zugewiesen bekommen haben.
Page 31
DEUTSCH PPPoE-Verbindung A Wählen Sie als Ihren WAN-Verbindungstyp PPPoE. BGeben Sie Service Name (Servicename) (optional), User Name (Benutzername) und Password (Passwort) ein. C Wählen Sie Get automatically from your ISP (Automatisch vom Internetdienstanbieter laden), wenn Sie von Ihrem Internetdienstanbieter keine feste IP-Adresse zugewiesen bekommen haben. Weiter mit E. Wählen Sie Use fixed IP address provided by your ISP (Vom Internetdienstanbieter vorgegebene feste IP- Adresse verwenden), um dem Prestige eine feste und eindeutige IP-Adresse zu geben.
Page 33
DEUTSCH PPTP-Verbindung A Wählen Sie als Ihren WAN-Verbindungstyp PPTP. BGeben Sie User Name (Benutzername) und Password (Passwort) ein. C Wählen Sie Get automatically from your ISP (Automatisch vom Internetdienstanbieter laden), wenn Sie von Ihrem Internetdienstanbieter keine feste PPTP IP-Adresse zugewiesen bekommen haben. Oder wählen Sie Use fixed IP address (Feste IP-Adresse verwenden), um dem Prestige eine feste und eideutige PPTP IP-Adresse sowie Subnet-Mask zuzuweisen.
Page 35
Sie auf Finish (Fertig stellen). 4 Bandwidth Management Wizard (Bandbreitenmanagement- Assistent) Klicken Sie im Willkommen-Fenster des Einrichtungsassistenten von ZyXEL auf den Hyperlink Go to Bandwidth Management Wizard (optional) (Zum Bandbreitenmanagement-Assistenten) oder wählen Sie die Option Bandwidth Management wizard (Bandbreitenmanagement-Assistent).
Page 36
DEUTSCH SCHRITT 1: Allgemeine Informationen Wählen Sie das Kontrollfeld Active (Aktiv). Der Prestige steuert nicht die dem Datenverkehr, der an einer Schnittstelle eingeht, zugewiesene Bandbreite. Geben Sie bei Managed Bandwidth (Verwaltete Bandbreite) einen Wert in kbps (2 bis 100.000) ein, der dem Datenverkehr zugewiesen werden soll.
Page 37
DEUTSCH SCHRITT 3: Festlegen der Priorität Wählen Sie als Priorität High (Hoch), Mid (Mittel) oder Low (Niedrig), mit der die Verteilung der Bandbreite auf die gewählten Dienste gesteuert werden soll. Alle Dienste mit der Priorität High (Hoch) erhalten soviel Bandbreite wie erforderlich. Wenn mehrere Dienste dieselbe Priorität haben, wird die Bandbreite zu gleichen Teilen geteilt.
Page 38
DEUTSCH PROBLEM LÖSUNGSMÖGLICHKEIT Ich kann von meinem Computer Prüfen Sie die Kabelverbindung zwischen Computer und Prestige. aus nicht auf den Prestige Die IP-Adresse des Prestige hat sich geändert. Geben Sie die neue Adresse als zugreifen. Website-Adresse ein. Stellen Sie sicher, dass sich die IP-Adresse des Computers im selben Subnetz wie die des Prestige befindet (siehe Abschnitt 5.1).
Page 39
9 Schließen Sie das Fenster Netzwerkverbindungen. 5.2 Schritte zum Ansehen der Produktzertifizierung(en) 1 Besuchen Sie www.zyxel.com. 2 Wählen Sie auf der ZyXEL-Homepage aus der Liste der Produkte Ihr Produkt aus. 3 Wählen Sie auf dieser die Zertifizierung aus, die Sie gerne angezeigt haben möchten.
ESPAÑOL ESPAÑOL Vista previa El Prestige es un router de banda ancha con un switch incorporado de 10/100 Mbps con cuatro puertos. El Prestige hace fácil la configuración de una red doméstica o de oficina y el acceso compartido a Internet a través de módem de banda ancha (cable/DSL).
Page 41
ESPAÑOL 1 Conexiones del hardware Realice lo siguiente para crear conexiones de hardware para la configuración inicial. Conexión WAN Conecte su módem al puerto “WAN” usando el cable que venía con su módem. Conexión LAN Conecte su ordenador a un puerto "LAN" usando el cable Ethernet incluido Conexión puerto impresora USB Utilice un cable USB para conectar una impresora USB a este puerto.
Page 42
(consulte la Guía del usuario para especificaciones sobre el adaptador de corriente por regiones). Los LEDs Mire a los LEDs del panel frontal. Cuando conecte la alimentación, los LEDs PWR y WLAN (P-335WT) se encenderán. Los LEDs LAN y WAN se encenderán si se realizan correctamente las conexiones correspondientes.
Page 43
DHCP desde el ISP. PASO 2: LAN inalámbrica (P-335WT) Configure UNO de los siguientes tipos de seguridad en el Prestige: • Seguridad Auto (Automática): Utiliza la seguridad WPA-PSK con una clave pre-compartida generada automáticamente.
Page 44
ESPAÑOL • None (Ninguna): No tiene seguridad LAN inalámbrica configurada. Si no activa ninguna seguridad inalámbrica en su Prestige, su red es accesible desde cualquier dispositivo de red inalámbrico dentro del alcance. • Seguridad Basic (Básica): WEP (Wired Equivalent Privacy) cifra los cuadros de datos antes de transmitir por la red inalámbrica.
Page 45
ESPAÑOL Seleccione seguridad Básica (WEP) A Introduzca un nombre único para identificar al Prestige en la LAN inalámbrica. B Deje la configuración predeterminada. El Prestige y el cliente inalámbrico deben usar el mismo ID de canal. C Seleccione seguridad Básica (WEP). D Puede generar o introducir manualmente una clave WEP de los siguientes modos: Introduciendo una Passphrase (Frase secreta) (hasta 32 caracteres imprimibles) y haciendo clic en Generate (Generar).
Page 46
ESPAÑOL Extienda la seguridad (WPA-PSK) o (WPA2-PSK). A Introduzca un nombre único para identificar al Prestige en la LAN inalámbrica. B Deje la configuración predeterminada. El Prestige y el cliente inalámbrico deben usar el mismo ID de canal. C Seleccione seguridad WPA-PSK o WPA2-PSK. D Escriba una clave pre-compartida para tener una conexión inalámbrica más segura que el cifrado WEP.
Page 47
ESPAÑOL PASO 3: El asistente intentará detectar qué tipo de conexión WAN está utilizando. Si el asistente no detecta un tipo de conexión, deberá seleccionar UNO en el cuadro de la lista desplegable. Consulte a su ISP para comprobar que utiliza el tipo correcto: 1 Ethernet 2 PPPoE...
Page 48
ESPAÑOL 3 PPTP. Nota: Si se le ha facilitado una configuración de acceso a Internet, introdúzcala en los campos siguientes. De lo contrario, deje los valores predeterminados y haga clic en Next (Siguiente) Conexión Ethernet A Seleccione Ethernet como tipo de conexión WAN. B Seleccione Get automatically from your ISP (Obtener automáticamente de su ISP) si su ISP no le asignó...
Page 50
ESPAÑOL Conexión PPPoE A Seleccione PPPoE como tipo de conexión WAN. BEscriba el Service Name (Nombre de servicio) (Opcional), User Name (Nombre de usuario) y Password (Contraseña). C Seleccione Get automatically from your ISP (Obtener automáticamente de su ISP) si su ISP no le asignó una dirección IP fija.
Page 52
ESPAÑOL Conexión PPTP A Seleccione PPTP como tipo de conexión WAN. BEscriba un User Name (Nombre de usuario) y Password (Contraseña) C Seleccione Get automatically from your ISP (Obtener automáticamente de su ISP) si su ISP no le asignó una dirección IP PPTP fija. O seleccione Use fixed IP address (Utilizar dirección IP fija) para dar al Prestige una dirección IP PPTP única y fija y una máscara de subred.
Page 54
(opcional) o haga clic en la opción Bandwidth Management wizard (Asistente para la administración del ancho de banda) en la pantalla de bienvenida de la Configuración del asistente de ZyXEL. La administración de la banda ancha le permite controlar la cantidad de banda ancha que sale del puerto WAN del Prestige y priorizar la distribución...
Page 55
ESPAÑOL PASO 1: Información general Seleccione la casilla de verificación Active (activa). El Prestige no controla el ancho de banda asignado al tráfico que viene a una interfaz. Introduzca la cantidad de Managed Bandwidth (Ancho de banda administrado) en kbps (2 a 100.000) que desea asignar para el tráfico.
Page 56
ESPAÑOL PASO 3: Configuración de prioridad Seleccione la prioridad High (Alta), Mid (Media) o Low (Baja) para controlar la distribución del ancho de banda para los servicios seleccionados. A un servicio con la prioridad High (Alta) se le da todo el ancho de banda que necesite. Si selecciona servicios con la misma prioridad, entonces el ancho de banda se divide por igual entre todos esos servicios.
Page 57
ESPAÑOL PROBLEMA SOLUCIÓN No se puede acceder al Compruebe la conexión de los cables de su ordenador al Prestige. Prestige desde mi ordenador. Si la dirección IP del Prestige ha cambiado, introduzca la nueva como dirección de sitio web. Compruebe que la dirección IP del ordenador esté en la misma subred que la dirección IP del Prestige (ver sección 5.1).
Page 58
Procedimiento para ver la(s) certificación(es) del producto 1 Vaya a www.zyxel.com. 2 Seleccione su producto de la lista desplegable en la página inicial de ZyXEL para ir a la página de ese producto. 3 Seleccione la certificación que desee visualizar en esta página.
FRANÇAIS FRANÇAIS Présentation Le Prestige est un routeur à large bande avec un commutateur 10/100 Mbps à quatre ports intégré. Le Prestige facilite l'installation d'un petit réseau domestique ou d'entreprise et permet de partager l'accès à Internet via un modem large bande (câble/DSL). Les caractéristiques principales du Prestige comprennent un firewall, un serveur d'impression, un VPN, un filtrage du contenu, le NAT et l'UPnP.
Page 60
(voir le guide de l'utilisateur pour les spécifications sur l'adaptateur d'alimentation par région). Les LED Observez les LED du panneau avant. Quand vous connectez l'alimentation, les LED PWR et WLAN (P-335WT) s'allument. Les LED LAN et WAN s'allument si les connexions correspondantes sont...
Page 61
FRANÇAIS 2 Accéder au configurateur Web 1 Lancez votre navigateur web. Entrez “192.168.1.1” comme adresse de site Web. Remarque : Si vous ne voyez pas l'écran suivant, allez à la section 2 La fenêtre Password (Mot de passe) s'affiche. 4 Cliquez sur Go Wizard setup (Aller à l'assistant de Entrez le mot de passe ("1234"...
Page 62
DHCP de l'ISP est utilisé. ETAPE 2: LAN Sans Fil (P-335WT) Configurez UN des types de sécurité sans fil suivants sur le Prestige. • Sécurité Auto : Utilisez la sécurité WPA-PSK avec une clé prépartagée générée automatiquement. Visualisez la clé...
Page 63
FRANÇAIS OTIST • OTIST (One-Touch Intelligent Security Technology) permet à votre Prestige d'attribuer la SSID du Prestige aux clients sans fil et les paramètres de cryptage WEP statique ou WPA-PSK. Le client sans fil doit aussi supporter OTIST et avoir OTIST activé. Sécurité...
Page 64
FRANÇAIS Sécurité de base (WEP) A Saisissez un nom unique pour identifier le Prestige dans le LAN sans fil. B Laisser le paramètre par défaut. Le Prestige et le client sans fil doivent utiliser la même ID de canal. C Sélectionnez la sécurité de base (WEP). D Vous pouvez générer ou entrer manuellement une clé...
Page 65
FRANÇAIS Sécurité (WPA-PSK) ou (WPA2-PSK) étendue A Saisissez un nom unique pour identifier le Prestige dans le LAN sans fil. B Laisser le paramètre par défaut. Le Prestige et le client sans fil doivent utiliser la même ID de canal. C Sélectionnez la sécurité...
Page 66
FRANÇAIS ETAPE 3: L'assistant essaie de détecter le type de connexion WAN que vous utilisez. Si l'assistant ne détecte pas de type de connexion, vous devez en sélectionner UN dans la liste déroulante. Voyez auprès de votre ISP pour être sûr d'utiliser le type correct : 1 Ethernet 2 PPPoE...
Page 67
FRANÇAIS 3 PPTP. Remarque : Si vous avez obtenu les paramètres d'accès Internet, saisissez-les dans les champs suivants. Sinon laissez les paramètres par défaut et cliquez simplement sur Next (Suivant) Connexion Ethernet A Sélectionnez Ethernet comme type de connexion WAN. B Sélectionnez Get automatically from your ISP (Obtenir automatiquement de l'ISP) si votre ISP ne vous a pas attribué...
Page 69
FRANÇAIS Connexion PPPoE A Sélectionnez PPPoE comme étant votre type de connexion WAN. BTapez un Service Name (nom de service) (optionnel), User Name (nom d'utilisateur) et Password (mot de passe). C Sélectionnez Get automatically from your ISP (Obtenir automatiquement de l'ISP) si votre ISP ne vous a pas attribué...
Page 71
FRANÇAIS Connexion PPTP A Sélectionnez PPTP comme type de connexion WAN. BTapez un User Name (nom d'utilisateur) et Password (un mot de passe) C Sélectionnez Get automatically from ISP (Obtenir automatiquement de l'ISP) si votre ISP ne vous a pas attribué...
Page 73
Cliquez sur le lien hypertexte Go to Bandwidth Management Wizard (Aller à l'assistant de gestion de bande passante) (optionnel) ou cliquez sur l'option Bandwidth Management wizard (d'assistant de gestion de bande passante) dans l'écran Bienvenue à l'assistant d'installation de ZyXEL. La gestion de bande passante vous permet de contrôler la quantité...
Page 74
FRANÇAIS ETAPE 1: Informations générales Sélectionnez la case à cocher Active. Le Prestige ne contrôle pas la bande passante allouée au trafic entrant dans une interface. Entrez la quantité de Managed Bandwidth (bande passante gérée) en kbps (2 à 100 000) que vous désirez allouer au trafic.
Page 75
FRANÇAIS ETAPE 3: Installation des priorités Sélectionnez priorité High (Haute),Mid (Moyenne) ou Low (Faible) pour contrôler la distribution de la bande passante des services sélectionnés. Un service avec une priorité High (Haute) reçoit toute la bande passante dont il a besoin. Si vous sélectionnez des services comme ayant la même priorité, alors la bande passante est répartie également entre ces services.
Page 76
FRANÇAIS PROBLÈME ACTION CORRECTIVE Impossible d'accéder au Vérifiez la connexion du câble entre votre ordinateur et le Prestige. Prestige à partir de mon Si l'adresse IP du Prestige a changé, entrez alors la nouvelle comme adresse ordinateur. du site web. Vérifiez que l'adresse IP de votre ordinateur se trouve dans le même sous- réseau que l'adresse IP du Prestige (voir la section 5.1).
Page 77
5.2 Procédure pour Afficher la (les) certification(s) d'un produit 1 Allez à www.zyxel.com. 2 Sélectionnez votre produit dans la boîte de la liste déroulante dans la page d'accueil de ZyXEL pour aller à la page de ce produit. Sélectionnez la certification que vous désirez consulter dans cette page.
ITALIANO ITALIANO Cenni generali Prestige è un broadband router che incorpora uno switch a quattro porte 10/100 Mbps. Il Prestige semplifica la configurazione di una piccola rete domestica o per un piccolo ufficio e consente di condividere l'accesso a Internet attraverso un model a banda larga (via cavo/xDSL). Le caratteristiche-chiave del Prestige includono firewall, server di stampa, VPN, filtro dei contenuti, NAT e UPnP.
Page 79
ITALIANO 1 Collegamenti hardware Di seguito sono illustrati i collegamenti hardware per l'installazione iniziale. Collegamento WAN Collegare il modem alla porta “WAN” utilizzando il cavo fornito a corredo con il modem. Collegamento LAN Collegare il computer alla porta "LAN" utilizzando un cavo Ethernet fornito a corredo. Collegamento porta per stampante USB Utilizzare un cavo USB per collegare una stampante USB a questa porta.
Indicatori LED Sul pannello frontale sono presenti alcuni LED. Quando si collega l'alimentazione, i LED PWR e WLAN (P-335WT) si accendono. I LED LAN e WAN si accendono se i relativi collegamenti sono stati eseguiti correttamente. 2 Accesso allo strumento di configurazione Web 1 Avviare il browser.
Page 81
DHCP dell'ISP. FASE 2: LAN Wireless (P-335WT) Configurare UNO dei seguenti tipi di protezione wireless sul Prestige: • Protezione Auto: utilizza la protezione WPA-PSK con una chiave condivisa in precedenza generata automati- camente. Visualizzare la chiave condivisa in precedenza generata nella schermata Wireless LAN.
Page 82
ITALIANO • Nessuna: nessuna protezione LAN wireless configurata. Se non si ailita alcuna protezione wireless sul Pres- tige, la rete sarà accessibile a qualsiasi periferica wireless di rete che si trova nel campo della portata. • Protezione di Base: WEP (Wired Equivalent Privacy) esegue la crittografia dei frame di dati prima di trasmet- terli sulla rete wireless.
Page 83
ITALIANO Protezione Base (WEP). A Immettere un nome univoco per identificare il Prestige nella LAN wireless. B Lasciare l'impostazione predefinita. Il Prestige e il client wireless devono utilizzare lo stesso ID di canale. C Selezionare la protezione Base(WEP). D È possibile generare o immettere manualmente una chiave WEP mediante una delle seguenti opzioni: Immettendo una Passphrase (fino a 32 caratteri stampabili) e facendo clic su Generate (genera).
Page 84
ITALIANO Protezione Estesa (WPA-PSK) o (WPA2-PSK) A Immettere un nome univoco per identificare il Prestige nella LAN wireless. B Lasciare l'impostazione predefinita. Il Prestige e il client wireless devono utilizzare lo stesso ID di canale. C Scegliere la protezione WPA-PSK o WPA2-PSK. D Immettere una chiave condivisa in precedenza per avere una connessione wireless più...
Page 85
ITALIANO FASE 3: La procedura guidata tenta di rilevare quale tipo di connessione WAN si sta utilizzando. Se la procedura guidata non rileva un tipo di connessione, è necessario selezionarne UNA dall'elenco a discesa. Chiedere al proprio ISP il tipo di connessione corretta: 1 Ethernet...
Page 86
ITALIANO 2 PPPoE 3 PPTP. Nota: Se sono state fornite le impostazioni di accesso Internet, immettere i campi seguenti. In caso contrario, lasciare le impostazioni predefinite e fare solo clic su Next (Avanti). Collegamento Ethernet A Scegliere Ethernet come tipo di connessione WAN. B Selezionare Ottieni automaticamente dall'ISP se l'ISP non ha assegnato un indirizzo IP statico.
Page 88
ITALIANO Collegamento PPPoE A Selezionare PPPoE utilizzando il tipo di connessione WAN. BImmettere Nome del servizio (opzionale), Nome utente e Password. C Selezionare Ottieni automaticamente dall'ISP se l'ISP non ha assegnato un indirizzo IP statico. Passare alla sezione E. Oppure selezionare Utilizza indirizzo IP fisso fornito dall'ISP per fornire al Prestige un indirizzo IP statico univoco.
Page 90
ITALIANO Collegamento PPTP A Selezionare PPTP utilizzando il tipo di connessione WAN. BImmettere Nome utente e Password C Selezionare Ottieni automaticamente dall'ISP se l'ISP non ha assegnato un indirizzo IP PPTP statico. Oppure selezionare Utilizza indirizzo IP fisso per fornire al Prestige un indirizzo IP statico univoco. D Immettere un indirizzo IP del server PPTP E Immettere ID connessione/Nome (se forniti) F Selezionare Ottieni automaticamente dall'ISP se l'ISP non ha assegnato un indirizzo IP statico.
Page 92
4 Gestione guidata banda Fare clic sul collegamento Passare a Gestione guidata banda (opzionale) oppure fare clic sull'opzione Gestione guidata banda nella schermata iniziale della configurazione ZyXEL. La gestione della larghezza di banda consente di controllare la quantità di banda dati che passa attraverso la porta WAN del Prestige e di dare priorità...
Page 93
ITALIANO FASE 1: Informazioni generali Selezionare la casella di controllo Active (attiva). Il Prestige non controlla la banda allocata al traffico che passa in un'interfaccia. Inserire la quantità di banda gestita espressa in kbps (da 2 a 100.000) che si desidera allocare per il traffico. È...
ITALIANO FASE 3: Configurazione priorità Selezionare la priorità Alta, Media o Bassa per controllare la distribuzione della banda ai servizi selezionati. A un servizio con priorità Alta viene data tutta la banda di cui necessita. Se si selezionano servizi di pari priorità, la banda viene divisa egualmente tra i servizi.
Page 95
ITALIANO PROBLEMA AZIONE CORRETTIVA Impossibile accedere allo Controllare il collegamento dei cavi tra il computer e il Prestige. Prestige dal mio computer. Se l'indirizzo IP del Prestige è cambiato, immettere l'indirizzo nuovo nella barra degli indirizzi. Assicurarsi che l'indirizzo IP del computer sia nella stessa subnet dell'indirizzo IP del Prestige (vedere la sezione 5.1).
Page 96
5.2 Procedura per visualizzare le certificazioni di un prodotto 1 Aprire la pagina www.zyxel.com. 2 Selezionare il prodotto dall'elenco di riepilogo a discesa nella Home Page di ZyXEL per passare alla pagina del prodotto in questione. 3 Selezionare da questa pagina la certificazione che si desidera visualizzare.
Page 98
區域網路連接 將您的電腦用所附的乙太網路電纜連接到一個 「LAN」埠。 USB 印表機連接 請以 USB 傳輸線將 USB 印表機連接到此埠。Prestige 內建有列印伺服器可允許在網路上共用印表機。 Prestige 會自動偵測出 USB 印表機的品牌和型號。 電源連接 用所附的電源轉換器將 「POWER」 插座連接到適當的電源 ( 有關各區域的電源轉換器規格請查閱使用者手冊 )。 請檢視前面板的 LED 。 接上電源後 , PWR 及 WLAN LED (P-335WT) 會點亮。 當相對的連接完成後 LAN 與 WAN LED 會 點亮。...
Page 107
中文 PPTP 連接 A 選擇 PPTP 為廣域網路連線類型。 B 輸入一個 使用者名稱及密碼 C 如果您的 ISP 不配置固定的 PPTP IP 位址,選擇 自動由 ISP 取得 。 選擇 使用固定 IP 位址以給予 Prestige 一個固定的、唯一的 PPTP IP 位址及子網路遮罩。 D 輸入一個 PPTP 伺服器 IP 位址 E 輸入一個 連線識別碼 / 名稱 ( 如果有提供 ) F 如果您的...