SEELEY INTERNATIONAL Braemar Ecostar TH3 Installation Manual
Gas ducted heater
Hide thumbs
Also See for Braemar Ecostar TH3:
- Service manual (60 pages) ,
- Installation manual (18 pages)
Related Manuals for SEELEY INTERNATIONAL Braemar Ecostar TH3
Summary of Contents for SEELEY INTERNATIONAL Braemar Ecostar TH3
- Page 1 INSTALLATION MANUAL Braemar Ecostar TH3, TH4, TH5, THM5 and THM6 Gas Ducted Heater Braemar Supernova TSS3, TSS4, TSS5 and TSS6 Gas Ducted Heater...
- Page 2 TH3, TH4, TH5, TSS3, TSS4, TSS5, TSS6...
- Page 3 HEATER LOCATION Avoid quiet areas: Preferred installation locations Directly above, below or outside bedrooms, living room, Above, below or outside laundry, bathroom, kitchen, garage lounge room, dining room etc. etc’ SEELEY INTERNATIONAL – INSTALLATION MANUAL...
- Page 4 HEATER CONFIGURATION Standard External Configuration Reversed External Configuration Increase inlet spigot and duct Swapping inlet & outlet panels diameter by 50mm The heater side panels can be moved to suit a range of installations. To do this: Remove heater top panel. ...
- Page 5 - this is not supplied by Braemar. Ensure that “COOL 2” is selected during system set-up to enable the system to operate the Braemar add-on cooling system - refer to “Commissioning” section in these instructions. SEELEY INTERNATIONAL – INSTALLATION MANUAL...
- Page 6 GOOD DUCTING GUIDLINES 1. Based on standard 100 x 300mm floor outlets and 150mm round ceiling outlets. 2. Minimum outlets open to achieve optimum turndown performance. Correct ductwork installation is critical to ensure correct operation of 3. 'X' in model refers to extra-air models - maximum outlets will be the heating system, and to prevent premature failure of the fan reduced when a add-on cooling coil is installed.
- Page 7 Ensure that all air is purged out of the gas line. for each additional zone - SCC/loom kit P/No 076010. Ensure that there are no gas leaks. and suitable wiring (not supplied by Seeley Zone dampers International) Gas Connection All Models SEELEY INTERNATIONAL – INSTALLATION MANUAL...
- Page 8 ELECTRICAL CONNECTION SCC CONNECTION - TH, TSS3 Electrical wiring & fittings must be installed by a licensed Electrician. The SCC is connected directly to the BSC eeley International recommends that all Braemar gas ducted In a multiple-SCC system, this becomes the “master” SCC. Refer heaters are wired with a dedicated circuit from the distribution to instructions supplied with zone kit for connection of up to 3 board with a separate circuit breaker.
- Page 9 SEELEY INTERNATIONAL – INSTALLATION MANUAL...
- Page 10 HEATER DIMENSIONS Dimension (mm) Heater Model TH3 and TH4 models TH315, TH415 TH320, TH420 TH325, TH425 TH330, TH430 TH435 TH3X20, TH4X20 TH3X25, TH4X25 TH3X30, TH4X30 TH5 models TH516 1150 1067 1003 TH523 1150 1067 1003 TH532 1165 1054 TH5X23 1150 1117 1003 TH5X32...
- Page 11 Terminate condensate plug is secure condensate drain in drain in a suitable location a suitable location Remove & Remove & discard lower discard lower Condensate drain elbow Condensate drain elbow transit plug transit plug SEELEY INTERNATIONAL – INSTALLATION MANUAL...
- Page 12 Flue 750 Min Isolation CEILING INSTALLATION valve Heater platform and clearances A = 385 or 510 ROOM FAN HX END supply Depends on model. The heater must be mounted on a platform to enable access for END OF OF HEATER servicing and maintenance.
- Page 13 Flue drain hose Remove & discard Remove & discard Terminate condensate transit plugs Terminate condensate transit plugs Condensate drain tee drain in a suitable location Condensate drain tee drain in a suitable location assembly assembly SEELEY INTERNATIONAL – INSTALLATION MANUAL...
- Page 14 FLUE SYSTEM & CONDENSATE DRAIN TH5, THM6, TSS5, TSS6 Flue system Braemar TH5, THM6, TSS5, TSS6 heaters must be flued using 100mm DWV plastic pipe and components complying with AS1260. The flue terminal on the side of the heater is designed to accept either the male end of a 100mm DWV M-F elbow, or 100mm DWV pipe. ...
- Page 15 1000 +/- 100 Pa -TH516 1100 +/- 100 Pa -TH523/32 800 +/- 100 Pa OUTLET PRESSURE TEST POINT Outlet pressure test point HIGH PRESSURE ADJUSTMENT Gas Out LOW PRESSURE ADJUSTMENT INLET PRESSURE TEST POINT INLET PRESSURE TEST POINT SEELEY INTERNATIONAL – INSTALLATION MANUAL...
- Page 16 SYSTEM SETUP Enable installed zones (SCC thermostat heaters only - not Set the time and day (SCC thermostat) required where multiple SCC's are installed) With the SCC in OFF mode, press and hold SET With the SCC in OFF mode, press and hold SET and press ZONE 1 ...
- Page 17 WARRANTY SERVICE: 1300 650 644 TECHNICAL SUPPORT: 1300 650 399 Please have your appliance model number, serial number, and any displayed fault codes available prior to calling. SEELEY INTERNATIONAL – INSTALLATION MANUAL...
- Page 18 DIAGNOSTIC CODES - Non Modulating Heaters (SCC thermostat required - refer service manual for full instructions) 3 STAR HEATERS Code Shut down SCC display Description type P-100 closed at start Reset, 1 P-100 failed to close Reset, 2 P-100 open during run Normal Ignition failure Reset, 7...
- Page 19 SW 4 Heater model THM516N THM520N Heaters are THM530N supplied Example THM618N pre-set to THM623N the follow- THM623N THM632N dipswitch THM5X20 LPG settings 1 2 3 4 THM5X30 LPG THM6X23 LPG THM6X32 LPG TSS420N TSS523N TSS623N SEELEY INTERNATIONAL – INSTALLATION MANUAL...
- Page 20 Warranty Service Australia 1-300-650-644 seeleyinternational.com It is the policy of Seeley International to introduce continual product improvement. Accordingly, specifications are subject to change without notice. Please consult with your dealer to confirm the specifications of the model selected. www.braemar.com.au 645377a...
Need help?
Do you have a question about the Braemar Ecostar TH3 and is the answer not in the manual?
Questions and answers