Related Manuals for SW-Motech BC.HTA.22.740.35800
Summary of Contents for SW-Motech BC.HTA.22.740.35800
- Page 1 ANBAUANLEITUNG mounting instructions • instructions de montage • instrucciones de montaje • istruzioni di montaggio BC.HTA.22.740.35800 beinhaltet • contains • contient • contiene • contiene HTA.22.740.85800/B BC.HTA.00.740.31000 BC.HTA.00.740.12200/B...
- Page 2 ~ 1.25 h. EASY DIFFICULT ENGLISH ·Thank you for choosing this premium product from SW-MOTECH. PREPARATION: Read the mounting instructions carefully and make sure Visit our online shop for more information (e.g. model assignments). Required that all parts on the parts list are available.
- Page 3 Use thread locker: Indicates that a thread must be coated with liquid thread locker. H (HIGH): high strength; M (MEDIUM): medium strength; L (LOW): low strength. The content translation is automated. Errors and omissions excepted © SW-MOTECH GmbH & Co. KG Subject to technical and design changes.
- Page 4 ø 5,3; DIN 9021 MU.A4.05.01.985.70 SC.A2.05.012.01.7380.M3 US.A2.053.01.9021 M8 x 25; DIN 912 M8 x 16; ISO 7380 SC.ST.08.025.01.912.088 SC.ST.08.016.02.7380.109 The content translation is automated. Errors and omissions excepted © SW-MOTECH GmbH & Co. KG Subject to technical and design changes.
- Page 5 Tighten the screws (5) as specified in the mounting instructions. CAUTION: Tightening the screws (5) too tightly will damage the plastic parts. × × 2.5 Nm The content translation is automated. Errors and omissions excepted © SW-MOTECH GmbH & Co. KG Subject to technical and design changes.
- Page 6 Pay attention to the attachment point shown in the detailed drawing. Do not tighten the screws (13) yet. × × × 1.5 Nm × The content translation is automated. Errors and omissions excepted © SW-MOTECH GmbH & Co. KG Subject to technical and design changes.
- Page 7 Pull the upper exhaust cover out of its anchor, and remove it from the vehicle. The content translation is automated. Errors and omissions excepted © SW-MOTECH GmbH & Co. KG Subject to technical and design changes.
- Page 8 MOUNTING STEP · READ AND KEEP MOUNTING INSTRUCTIONS! Loosen the screws of the lower heat shield and remove it from the vehicle. The content translation is automated. Errors and omissions excepted © SW-MOTECH GmbH & Co. KG Subject to technical and design changes.
- Page 9 MOUNTING STEP · READ AND KEEP MOUNTING INSTRUCTIONS! Loosen the original screws of the passenger footrest bracket on both sides and remove them from the vehicle. The content translation is automated. Errors and omissions excepted © SW-MOTECH GmbH & Co. KG Subject to technical and design changes.
- Page 10 Then mount all the original parts and screws dismantled in steps [3] and[4] × back onto the vehicle. Tighten the original screws according to the manufacturer's instructions. The content translation is automated. Errors and omissions excepted © SW-MOTECH GmbH & Co. KG Subject to technical and design changes.
- Page 11 WARNING: before starting your journey, check that all components are securely fastened. Remove the connectors (9/10) from the vehicle when riding WITHOUT saddlebags. The content translation is automated. Errors and omissions excepted © SW-MOTECH GmbH & Co. KG Subject to technical and design changes.
- Page 12 TÜV regulations. After assembly, have parts that are subject to registration entered in the vehicle documents by your test centre. The content translation is automated. Errors and omissions excepted © SW-MOTECH GmbH & Co. KG Subject to technical and design changes.
- Page 19 ~ 0.25 h. EASY DIFFICULT ENGLISH ·Thank you for choosing this premium product from SW-MOTECH. PREPARATION: Read the mounting instructions carefully and make sure Visit our online shop for more information (e.g. model assignments). Required that all parts on the parts list are available.
- Page 20 ASSEMBLY section, the vehicle manufacturer's our online shop: specifications must be observed and applied. www.sw-motech.com The content translation is automated. Errors and omissions excepted © SW-MOTECH GmbH & Co. KG Subject to technical and design changes.
- Page 21 PARTS LIST · READ AND KEEP MOUNTING INSTRUCTIONS! BC.HTA.00.740.003.02 The content translation is automated. Errors and omissions excepted © SW-MOTECH GmbH & Co. KG Subject to technical and design changes.
- Page 22 Thoroughly clean any grease and dirt residues from the determined adhesive positions. Remove the foils from the adhesive surfaces of the abrasion/edge protectors (1). The content translation is automated. Errors and omissions excepted © SW-MOTECH GmbH & Co. KG Subject to technical and design changes.
- Page 23 Check the correct positioning of the abrasion/edge protectors (1) again once the BLAZE saddlebags have been loaded. The content translation is automated. Errors and omissions excepted © SW-MOTECH GmbH & Co. KG Subject to technical and design changes.
- Page 24 TÜV regulations. After assembly, have parts that are subject to registration entered in the vehicle documents by your test centre. The content translation is automated. Errors and omissions excepted © SW-MOTECH GmbH & Co. KG Subject to technical and design changes.
Need help?
Do you have a question about the BC.HTA.22.740.35800 and is the answer not in the manual?
Questions and answers