Related Manuals for Stjarna Icon 220
Summary of Contents for Stjarna Icon 220
- Page 1 Sauna "Icon" 220,Ø226 NB! Please read whole manual before start. All given measurements are in millimeters! (ICO-26-PES-PTS-001)
- Page 2 Sauna "Icon" 220,Ø226 Details list 1. 12 m x1 kmpl. (ICO-26-PES-PTS-001)
- Page 3 Sauna "Icon" 220,Ø226 Details list 2. ~430 x370 (ICO-26-PES-PTS-001)
- Page 4 Icon Ø226 Wooden front wall assembly Details Cut board from pallet L=~2100mm. 16x J Fix it diagonally to make wall more rigid during the installation. 2x I (ICO-26-PES-PTS-001)
- Page 5 Icon Ø226 Wooden back wall assembly Details Cut board from pallet L=~2100 mm. Drill holes Ø4mm before screws. 4x I 2x M (ICO-26-PES-PTS-001)
- Page 6 Sauna "Icon" 220,Ø226 Back 12x M 6x DET 2 mm=mm DET 3b/H 2x DET 1 have slots 12x M at the ends. Front DET 3b DET B 4x M DET A1 Make all 3 sets, rest of them You will need later. (ICO-26-PES-PTS-001)
- Page 7 Sauna "Icon" 220,Ø226 DET 3b DET 3a/H Place DET 3b/W and DET 3b/H Fix screws over the one board, DET W have slots side by side about in the diagonally in every board. at the ends. middle of the floor. DET 3b/W Don´t fix board yet! DET 3b/H...
- Page 8 Sauna "Icon" 220,Ø226 4x H Use waterlevel Check walls installation manual on extra pages! Sauna wall configuration depends on Your model! mm=mm Brackets inside DET 3c DET 3d Fix temporarily to support walls. Sauna midpoint Drill holes Ø4mm before screws. 2x H 3x H (ICO-26-PES-PTS-001)
- Page 9 Sauna "Icon" 220,Ø226 Remove DET 3c DET 3d Important! Leave the gap ~7 mm. Place DET A1 before wall boards Prepare the details as described on Page 1. See the next page. DET 3c DET 3d (ICO-26-PES-PTS-001)
- Page 10 Sauna "Icon" 220,Ø226 DET 3d DET 3c DET 3d DET 3c Lift nose slightly up before installing combined detail. Glue Use wood glue between boards Use proper size screws(6pc.) Drill holes before screws. (ICO-26-PES-PTS-001)
- Page 11 Sauna "Icon" 220,Ø226 1xDET A2 12x H ~240 mm 2xDET 4a 56x H Drill holes Ø4mm 14xDET 4b before screws. Use ratchet strap so close to the ends that You can remove screws. Don´t fix it very tightly yet! DET A2 min.60 (ICO-26-PES-PTS-001)
- Page 12 Sauna "Icon" 220,Ø226 Remove all screws 2xDET A2 ~240 mm Proceed the same way as described on previous page. Remove all brackets. Now fix all nuts tightly! Upper vent Remove ratchet strap! 1xDET G 6x K Lower vent 3xDET F 6x K (ICO-26-PES-PTS-001)
- Page 13 Sauna "Icon" 220,Ø226 Install DET 10b in the Drill holes Ø4mm before screws. middle of the saunaroom. 2x DET 10b 4x DET 10a 4x H 12x H NB! If Your sauna equipped with front glass-wall, the sauna benches installation manual included in front glass-wall installation manual.
- Page 14 Sauna "Icon" 220,Ø226 Drill holes Ø4mm Drill holes Ø4mm before screws. before screws. 8x H 2x DET 10b Door side 2x DET 11a Drill holes Ø4mm Drill holes Ø4mm before screws. before screws. 2x M 2x DET 11 4x H 4x H 2x DET 11b (ICO-26-PES-PTS-001)
- Page 15 Sauna "Icon" 220,Ø226 10x J 4x I 2x J 5xDET 20 1xDET 20a 6x I(K) Leave the gap between board and wall. 2xDET L 1xDET 20b 2x J 2x DET 15a 6x I 2x H 2x DET 15b Cut from this side if needed! If Your sauna heater is smaller, You can cut DET 15a to size, that suits with Your heater.
- Page 16 Sauna "Icon" 220,Ø226 Place saunaheater first. 4x J 6x H 1x DET 15d 2x M 1x DET 21 2x DET 21c 2x DET 21d 2x M 20x H (ICO-26-PES-PTS-001)
- Page 17 Sauna "Icon" 220,Ø226 Press door tightly against the wall and fasten from inside 2x DET 21a 2x DET 21b 8x H 16x J 10x H 2xDET 22 DET N NB! Before roof shingles, install underlay felt. Check underlay felt installation manual on extra pages.
- Page 18 Sauna "Icon" 220,Ø226 Shingles overlap on top Refract DET N into 3 pieces. DET N DET O Cut and use it other end. Check also roof shingles installation manual inside package. 1x DET 27 4xDET 25a 4xDET 25a 4xDET 25b 4xDET 25b 28x H 28x H...
- Page 19 Underlay felt installation manual. Cut off Check also underlay installation manual inside the package! Bitumen strip is against ~50 mm the previous layer. ~50 mm over the edge. over the edge. Turn end to Clamp end the edge. to the edge. Cut off the parts that extend over the edge.
Need help?
Do you have a question about the Icon 220 and is the answer not in the manual?
Questions and answers