Related Manuals for Clarke CONTRACTOR PM1600/1
Summary of Contents for Clarke CONTRACTOR PM1600/1
- Page 1 1600W/110V PADDLE MIXER MODEL NO: PM1600 /1 PART NO: 6479567 OPERATING & MAINTENANCE INSTRUCTIONS ORIGINAL INSTRUCTIONS GC03/24...
- Page 2 INTRODUCTION Thank you for purchasing this CLARKE 110V Paddle Mixer. Before attempting to use this product, please read this manual thoroughly and follow the instructions carefully. In doing so you will ensure the safety of yourself and that of others around you, and you can look forward to your purchase giving you long and satisfactory service.
- Page 3 GENERAL SAFETY PROCEDURES CAUTION: FAILURE TO FOLLOW THESE PRECAUTIONS COULD RESULT IN PERSONAL INJURY, AND/OR DAMAGE TO PROPERTY. WORK ENVIRONMENT 1. Keep the work area clean, tidy and well lit. Cluttered and dark areas invite accidents 2. DO NOT operate power tools in explosive atmospheres, such as in the presence of flammable liquids, gases or dust.
- Page 4 6. NEVER attempt any repairs yourself. If you have a problem with this product contact your local CLARKE dealer. 7. DO NOT use the mixer for any purpose than that described in this manual.
- Page 5 ADDITIONAL PRECAUTIONS FOR PAINT MIXERS 1. NEVER use third party mixing attachments. Replacement parts can be obtained from you CLARKE dealer. Please keep these instructions in a safe place for future reference. SAFETY SYMBOLS...
- Page 6 ELECTRICAL CONNECTION WARNING! READ THESE ELECTRICAL SAFETY INSTRUCTIONS THOROUGHLY BEFORE CONNECTING THE PRODUCT TO A POWER SUPPLY. THE INSTALLATION OF THIS APPLIANCE SHOULD BE CARRIED OUT BY A COMPETENT ELECTRICIAN AND BE IN ACCORDANCE WITH CURRENT IEE WIRING REGULATIONS (BS4343). This product MUST be connected to a 110 Volt, 1 phase 50Hz supply through a suitably rated isolator switch.
- Page 7 Drive shaft Safety trigger Spanners The items above are supplied loose in the carton. If any are missing or damaged please contact the CLARKE dealer where you purchased the product. Parts & Service: 020 8988 7400 / E-mail: Parts@clarkeinternational.com or Service@clarkeinternational.com...
- Page 8 BEFORE USE WARNING: BEFORE REMOVING, OR INSTALLING THE MIXING BLADE, MAKE SURE THAT THE PLUG HAS BEEN REMOVED FROM THE POWER SUPPLY. FITTING THE MIXING BLADE 1. Screw the mixing blade shaft into the tool holder. 2. Use the two spanners supplied to tighten the mixing blade locking nut as shown.
- Page 9 OPERATION SWITCHING ON AND OFF 1. Ensure the mixing container is securely positioned on the floor. 2. Imerse the mixing paddle into the material to be mixed. 3. Set the speed control to low speed 4. Always hold the mixer with both hands.
- Page 10 2. Keep the unit clean and free from build up of any residual media material. The drive motor and bearings are sealed units and require no regular maintenance. Should you require assistance, contact your local CLARKE service agent. With the exception of changing the carbon brushes, there are no other user serviceable parts on this mixer.
- Page 11 COMPONENT PARTS-PM1600/1 Parts & Service: 020 8988 7400 / E-mail: Parts@clarkeinternational.com or Service@clarkeinternational.com...
- Page 12 COMPONENT PARTS - PM1600/1 Description No Description Screw ST3.9x13 Speed shift knob Rear cover Steel ball Carbon brush cover Spring Carbon brush Circlip 28 Brush holder Bush Housing Screw st4.8x50x25 Stator Gearbox Screw ST4.8x60 Bearing holder 22 Oil seal gasket Bearing 608 Bearing 6003 Rotor...
- Page 13 DECLARATION OF CONFORMITY-UK Parts & Service: 020 8988 7400 / E-mail: Parts@clarkeinternational.com or Service@clarkeinternational.com...
- Page 14 DECLARATION OF CONFORMITY-CE Parts & Service: 020 8988 7400 / E-mail: Parts@clarkeinternational.com or Service@clarkeinternational.com...
- Page 15 A SELECTION OF ITEMS FROM THE CLARKE RANGE Parts & Service: 020 8988 7400 / E-mail: Parts@clarkeinternational.com or Service@clarkeinternational.com...
Need help?
Do you have a question about the CONTRACTOR PM1600/1 and is the answer not in the manual?
Questions and answers