Related Manuals for Clarke PM1200
Summary of Contents for Clarke PM1200
- Page 1 1200/1600W PADDLE MIXERS MODEL NO: PM1200 & PM1600 PART NO: 6479560 6479565 OPERATING & MAINTENANCE INSTRUCTIONS ORIGINAL INSTRUCTIONS GC10/23...
-
Page 2: Specifications
INTRODUCTION Thank you for purchasing this CLARKE Paddle Mixer. Before attempting to use this product, please read this manual thoroughly and follow the instructions carefully. In doing so you will ensure the safety of yourself and that of others around you, and you can look forward to your purchase giving you long and satisfactory service. -
Page 3: General Safety Procedures
GENERAL SAFETY PROCEDURES CAUTION: FAILURE TO FOLLOW THESE PRECAUTIONS COULD RESULT IN PERSONAL INJURY, AND/OR DAMAGE TO PROPERTY. WORK ENVIRONMENT 1. Keep the work area clean, tidy and well lit. Cluttered and dark areas invite accidents 2. DO NOT operate power tools in explosive atmospheres, such as in the presence of flammable liquids, gases or dust. -
Page 4: Electrical Safety
6. NEVER attempt any repairs yourself. If you have a problem with this product contact your local CLARKE dealer. 7. DO NOT use the machine for any purpose than that described in this manual. -
Page 5: Safety Symbols
ADDITIONAL PRECAUTIONS FOR PAINT MIXERS 1. NEVER use third party mixing attachments. Replacement parts can be obtained from you CLARKE dealer. Please keep these instructions in a safe place for future reference. SAFETY SYMBOLS The meanings of the markings and symbols on the product are shown below... -
Page 6: Electrical Connections
ELECTRICAL CONNECTIONS WARNING: READ THESE ELECTRICAL SAFETY INSTRUCTIONS FULLY BEFORE CONNECTING THE MACHINE TO THE MAINS SUPPLY. This product is provided with a standard 13 amp, 230 volt (50Hz), BS 1363 plug, for connection to a standard, domestic electrical supply. Should the plug need changing, make sure that a plug of identical specification is used. - Page 7 Drive shaft Safety trigger Spanners The items above are supplied loose in the carton. If any are missing or damaged please contact the CLARKE dealer where you purchased the product. Parts & Service: 020 8988 7400 / E-mail: Parts@clarkeinternational.com or Service@clarkeinternational.com...
-
Page 8: Before Use
BEFORE USE WARNING: BEFORE REMOVING, OR INSTALLING THE MIXING BLADE, MAKE SURE THAT THE MAINS PLUG HAS BEEN REMOVED FROM THE MAINS POWER SUPPLY. FITTING THE MIXING BLADE 1. Screw the mixing blade shaft into the tool holder. 2. Use the two spanners supplied to tighten the mixing blade locking nut as shown. -
Page 9: Care And Maintenance
2. Keep the unit clean and free from build up of any residual media material. The drive motor and bearings are sealed units and require no regular maintenance. Should you require assistance, contact your local CLARKE service agent. With the exception of changing the carbon brushes, there are no other user serviceable parts on this mixer. - Page 10 COMPONENT PARTS-PM1600 Parts & Service: 020 8988 7400 / E-mail: Parts@clarkeinternational.com or Service@clarkeinternational.com...
- Page 11 COMPONENT PARTS - PM1600 Description No Description Screw ST3.9x13 Speed shift knob Rear cover Steel ball Carbon brush cover Spring Carbon brush Circlip 28 Brush holder Bush Housing Screw st4.8x50x25 Stator Gearbox Screw ST4.8x60 Bearing holder 22 Oil seal gasket Bearing 608 Bearing 6003 Rotor...
- Page 12 COMPONENT PARTS-PM1200 Parts & Service: 020 8988 7400 / E-mail: Parts@clarkeinternational.com or Service@clarkeinternational.com...
- Page 13 COMPONENT PARTS - PM1200 Description No Description Screw ST3.8x13 Key 5x10 Rear cover Oil seal Carbon brush cover S/t Screw 4.8x50 Carbon brush Gearbox Brush holder Housing Oil seal gasket Stator Bearing 6003 Screw ST4.8x55 Circlip 35 Upper handle Circlip 17...
- Page 14 DECLARATIONS OF CONFORMITY - PM1600 Parts & Service: 020 8988 7400 / E-mail: Parts@clarkeinternational.com or Service@clarkeinternational.com...
- Page 15 DECLARATION OF CONFORMITY - PM1200 Parts & Service: 020 8988 7400 / E-mail: Parts@clarkeinternational.com or Service@clarkeinternational.com...
Need help?
Do you have a question about the PM1200 and is the answer not in the manual?
Questions and answers