Download Print this page

Front Runner LAFB001 Quick Start Manual

Ford bronco (2021-current) side mount ladder

Advertisement

Quick Links

front runner
Before you start, take a moment to familiarize yourself with the Fitting Instructions and the included components.
IT IS CRITICAL THAT ALL FRONT RUNNER PRODUCTS BE PROPERLY AND SECURELY ASSEMBLED AND ATTACHED TO YOUR VEHICLE. IMPROPER ATTACHMENT COULD
RESULT IN AN AUTOMOBILE ACCIDENT, AND COULD CAUSE SERIOUS BODILY INJURY OR DEATH. YOU ARE RESPONSIBLE FOR ASSEMBLING AND SECURING ALL FRONT
RUNNER PRODUCTS TO YOUR VEHICLE, CHECKING THE ATTACHMENTS PRIOR TO USE, AND PERIODICALLY INSPECTING THE PRODUCTS FOR ADJUSTMENT, WEAR AND
DAMAGE. THEREFORE, YOU MUST READ AND UNDERSTAND ALL OF THE INSTRUCTIONS AND PRECAUTIONS SUPPLIED WITH YOUR FRONT RUNNER PRODUCT PRIOR TO
INSTALLATION OR USE. IF YOU DO NOT UNDERSTAND ALL OF THE INSTRUCTIONS AND CAUTIONS, OR IF YOU HAVE NO MECHANICAL EXPERIENCE AND ARE NOT THOROUGHLY
FAMILIAR WITH THE INSTALLATION PROCEDURES, YOU SHOULD HAVE THE PRODUCT INSTALLED BY A PROFESSIONAL INSTALLER OR OTHER QUALIFIED PERSONNEL.
NOTE: Front Runner will not be responsible for any damage caused by the failure to install the product according to these instructions.
LAFB001_REV_A01
Ford Bronco (2021-Current)
Side Mount Ladder
READ ME !
Thank you for purchasing a Front Runner Ford Bronco (2021 - Current) Ladder.
Refer to Page 2 for a list of all the components, quantities and tools required.
IMPORTANT WARNING!
Please call us if you have any questions about the installation of this product.
1
LAFB001
© 2024 FRONT RUNNER VEHICLE OUTFITTERS
ENG

Advertisement

loading
Need help?

Need help?

Do you have a question about the LAFB001 and is the answer not in the manual?

Questions and answers

Summary of Contents for Front Runner LAFB001

  • Page 1 FAMILIAR WITH THE INSTALLATION PROCEDURES, YOU SHOULD HAVE THE PRODUCT INSTALLED BY A PROFESSIONAL INSTALLER OR OTHER QUALIFIED PERSONNEL. NOTE: Front Runner will not be responsible for any damage caused by the failure to install the product according to these instructions.
  • Page 2 Ladder Rung Steps (226mm) Bottom Mounting Bracket M6 x 16 Button Head Screw M6 Nyloc Nut M6 Nut Cap M6 x 25 Thread Forming Screw Mounting Bracket RH side Mounting Bracket LH Side LAFB001_REV_A00 © 2024 FRONT RUNNER VEHICLE OUTFITTERS...
  • Page 3 Align the holes in the plate with the holes in the roof ledge refit the two screws removed in step 2.2. DO NOT FULLY TIGHTEN. Lower the roof back in position align and refit all the screws removed earlier and fully tighten. LAFB001_REV_A00 © 2024 FRONT RUNNER VEHICLE OUTFITTERS...
  • Page 4 2nd and 3rd rear slats, position the assembled ladder onto the side profile and insert the supplied BHM8x30 screws (Item 5) into the 2nd and 3rd slat holes. DO NOT FULLY TIGHTEN. LAFB001_REV_A00 © 2024 FRONT RUNNER VEHICLE OUTFITTERS...
  • Page 5 fitted in 2.7 and place the M6 Nut Caps (Item 12) over the nuts 10mm Refit the Slimline II Rear Corner that was removed in 2.4. Tightening Torque: M6 : 8-10Nm / 5.9 ft lb - 7.38 ft lb LAFB001_REV_A00 © 2024 FRONT RUNNER VEHICLE OUTFITTERS...
  • Page 6 IMPORTANT! FRONT RUNNER RACK KITS OFTEN HAVE A HIGHER LOAD RATING THAN THE VEHICLES THEY ARE MOUNTED TO. PLEASE REFER TO YOUR SPECIFIC VEHICLE MANUFACTURER FOR A RECOMMENDED ROOF RATING. FRONT RUNNER CANNOT BE RESPONSIBLE FOR IMPROPER LOADING BEYOND THE VEHICLE MANUFACTURER'S STATED LOAD CAPACITY.