BASI mySafe Premium Series Operating Manual

➂ ➃
Fi ng er se ns or
Kn ob
➁
c
M a g n e ti c d is
➅
e y
E m e rg e n c y k
1
Opening the door the first time
or emergency opening
Remove the magnetic disc ➁
Variant 1:
and insert the emergency key ➅ into the
emergency keyhole ➄.
Turn it in a clockwise direction.
Now you can open the safe with
the knob ➂.
Variant 2: Place four AA batteries in the
enclosed emergency power supply pack
➇ and push the plug into the battery
connection ➆ under the keypad.
Now you can enter the factory code/
management code 123456 or your own
personal code. Then confirm your
entry with #.
If your entries were successful, the green
indicator lights up and you can open the
safe door by turning the knob ➂ .
2
Opening the door
Touch the touch keypad ➀.
The display lights up.
Variant 1:
Enter your user code on
the touch keypad. Then confirm your
entry with #.
Variant 2: Place your saved finger on
the finger sensor ➃.
If your entries were successful, the green
indicator lights up and you can open the
safe door by turning the knob ➂ .
BASI GmbH · Konstantinstraße 387 · 41238 Mönchengladbach · Germany · info@basi.eu · www.basi.eu
➀
To uc h ke yp ad
➄ e y h o le
E m e rg e n c y k
n e c ti o n
➆
B a tt e r y c o n
3
Setting or changing the user
code (PIN code)
Open the safe door and briefly press the
Set/Reset key
Enter the management code on the touch
keypad ➀. Then confirm your entry with #.
The default management code set in the
factory is: 123456
Press key 1 to reset or change
your user code.
Now you can enter your new personal
1-8 digit code. This code must be entered
twice, each followed by #.
If your entries were successful, the
green indicator lights up. Complete
your entry with .
4
Setting or changing the
management code
Open the safe door and briefly press the
Set/Reset key
Enter the management code on the touch
keypad ➀. Then confirm your entry with #.
The default management code set in the
factory is: 123456
Press key 4 to reset or change the
management code.
Now you can enter your new management
code. This code must be entered twice,
each followed by #.
Operating manual
mySafe Premium
ly
p o w e r s u p p
➇
E m e r g e n c y
Factory code/management code: 123456
factory setting = demonstration mode (the safe can be opened with every finger)
➉
once.
➉
once.
(code and fingerprint)
➈
t
Ba tt er y co m pa rt m en
➉
S e t/ R e s e t k e y
If your entries were successful, the
green indicator lights up. Complete
your entry with .
5 Setting or adding fingerprints
(max. 30 fingers)
Open the safe door and briefly press the
➉
Set/Reset key once.
Enter the management code on the touch
keypad ➀. Then confirm your entry with #.
The default management code set in the
factory is: 123456
Press key 2 to set your fingerprint or to
add new fingerprints.
Place your finger on the finger sensor ➃.
This scan must be entered three times.
If your entries were successful, the
green indicator lights up. Complete
your entry with .
6 Deleting all fingerprints
Open the safe door and briefly press the
➉
Set/Reset key once.
Enter the management code on the touch
keypad ➂. Then confirm your entry with #.
The default management code set in the
factory is: 123456
Press key 3 to delete all fingerprints.
Attention! This operation cannot
be undone!
L E D li g h t