Download Print this page

HOKKIM HAMF-8 Manual

Control & protection relays
Hide thumbs Also See for HAMF-8:

Advertisement

Quick Links

HOKKIM
Giving You Control
HOKKIM INTEGRATED AMF CONTROL BOARD MANUAL FOR MODELS:
HAMF-8 AND HAMF-4
INTRODUCTION
Tha nk you for purch sing the Hokkim Integr ted Autom tic M ins F ilure Control Bo rd
model HAMF-8 or HAMF-4. We sh ll strive to provide you with the best service in terms of
technic l support, stock nd p rts repl cement. Thais m nu l should be re d through before
tteempting to inst ll the unit or repl ce f ulty p rts. A copy should be h nded to the owner's
m inten nce te m for future reference.
Thae design nd development of the Hokkim Integr ted AMF models comes from m ny ye rs
of studying the tr dition l AMF bo rds h rd wired with rel ys nd timers. Thae integr ted AMF is
b sed on tr dition l timers nd rel ys nd not on micro controllers. It is very fleexible, comes with
m ny fe tures nd e sy to use. Due to our policy of continuous development, we welcome
suggestions for improvements. Thaus, there m y be ch nges fteer this m nu l is printed. If in doubt,
do not hesit te to c ll for our technic l support.
PARTS IDENTIFICATION
Figures 1 & 3 show the top f ces with l beling of Light Emitteing Diode indic ting lights nd knob
djustments for the respective model. While figgures 2 & 4 show the botteom b se Printed Circuit
Bo rd with l beling of termin ls nd plug-in PCB c rds. We will now identify e ch PCB c rd nd
f mili rize you with the LED indic ting lights nd knob djustments. Once f mili rized, you will
be ble to follow the oper tion of the Integr ted AMF nd identify problems when they occur nd
repl ce the ppropri te c rd.
1) ESR - Emergency Stop Rel y.
RUN (green) LED On- Rel y energized to power the rest of the rel y c rds.
STOP (red) LED On - Rel y de-energized to cut power to the rest of the c rds except the
2) FMR - F ult Monitor Rel y.
RUN (green) LED On- No f ults detected by the F ult Al rm Rel ys.
TRIP (red) LED On - One or more f ults detected. Gener tor Stopped.
3) EST - Energized Stop Timer
ON (green) LED On - Energized stop rel y nd the del y timer ctiv ted.
UP ( mber) LED On - Time del y up nd stop rel y rele sed.
Time Adjustment
4) MFT - M ins F il Timer
ON (green) LED On - M ils f ilure detected nd del y timer ctiv ted.
UP ( mber) LED On - Timer rel y energized nd st rt gener tor sequence ctiv ted.
Time Adjustment
Selection
5) SDT - Shut Down Timer & Fuel Solenoid
ON (green) LED On - Fuel solenoid rel y ctiv ted.
ON (green) LED On - Shut Down Timer ctiv ted nd timer count down begins.
Time Adjustment
Control & Protection Rel ys
Energized Stop Timer.
- 0 to 20 Sec.
- 0 to 10 Sec.
- Norm lly Open or Norm lly Close to run.
- 0 to 20 Min

Advertisement

loading
Need help?

Need help?

Do you have a question about the HAMF-8 and is the answer not in the manual?

Questions and answers

Summary of Contents for HOKKIM HAMF-8

  • Page 1 HAMF-8 AND HAMF-4 INTRODUCTION Tha nk you for purch sing the Hokkim Integr ted Autom tic M ins F ilure Control Bo rd model HAMF-8 or HAMF-4. We sh ll strive to provide you with the best service in terms of technic l support, stock nd p rts repl cement.
  • Page 2 HOKKIM Control & Protection Rel ys Giving You Control...
  • Page 3 HOKKIM Control & Protection Rel ys Giving You Control...
  • Page 4 HOKKIM Control & Protection Rel ys Giving You Control...
  • Page 5 HOKKIM Control & Protection Rel ys Giving You Control...
  • Page 6 Cont ins met l oxide v ristors to bsorb volt ge surge, bove 56VDC, t termin ls T11 & T12. 15) MAMF - AMF Motherbo rd B se printed circuit bo rd for HAMF-8/4. TERMINALS IDENTIFICATION Now we will look t Figure 5 to identify the connection termin ls loc ted on the b se PCB. Thaese termin l connections shows you how to wired up the Integr ted AMF to extern l rel ys, push butteons, selector switch, bell, f ult sign l input, etc.
  • Page 7 HOKKIM Control & Protection Rel ys Giving You Control...
  • Page 8 HOKKIM Control & Protection Rel ys Giving You Control TERMINALS T01 TO T32 - MAIN CONTROLS T01 Positive supply (+12Vdc or +24Vdc) input direct from fuse or circuit bre ker. T02 Positive supply output protected by 10A fuse on b se PCB. For use, if required.
  • Page 9 HOKKIM Control & Protection Rel ys Giving You Control T23To Gener tor Run cont ct (Norm lly Open). From extern l 240VAC AFR rel y. T24To Cr nk Cutout cont ct (Norm lly Open). From extern l Speed Sensing Rel y TFQ-1.
  • Page 10 HOKKIM Control & Protection Rel ys Giving You Control To volt-free f ult sign l cont cts (Norm lly Open) No. 5. Close to +ve or -ve to trigger S6 To volt-free f ult sign l cont cts (Norm lly Open) No. 6. Close to +ve or -ve to trigger.
  • Page 11: Installation And Wiring

    INSTALLATION AND WIRING Thae HAMF-8/4 h s met l b se pl te with mounting holes in e ch corner. Pl ce the unit onto your switchbo rd p nel nd m rk the holes. Drill nd t p ccordingly. Afteer cle ning, mount the unit with ppropri te screws nd w shers.
  • Page 12 Afteer completing the wiring, use continuity tester to check th t the wiring re properly done nd the unit is re dy for testing. It should be noted th t the HAMF-8 / 4 is only designed for 12VDC or 24VDC.
  • Page 13 10. Wh t will h ppen is th t the Utilities Supply (TNB) will return. When this h ppen, the HAMF-8 / 4 will go into the shutdown mode. To test this, set the M ins F il Cont ct to the origin l position.
  • Page 14: Troubleshooting

    TROUBLE SHOOTING Thae HAMF-8 / 4 is designed in such w y th t p rts repl cement re e sy nd of minim l costs in comp rison to the cost of the whole unit. Thaere re 21 / 16 plug-in rel y c rds of only 13 diff erent types.
  • Page 15 Afteer t king c re th t the b se PCB is not d m ged, trouble shooting the HAMF-8 / 4 is e sy, in the worse scen rio, ll you h ve to do is to repl ce ll the 21 / 16 rel y c rds, which t kes less then 10 minutes.

This manual is also suitable for:

Hamf-4