Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Subscribe to Our Youtube Channel
Related Manuals for HDWR HD150
Summary of Contents for HDWR HD150
- Page 1 User Manual Wired USB Desktop QR & Barcode Scanner HD150...
-
Page 2: Table Of Contents
Table of contents Specifications: ................................3 Set contents: ................................... 4 Advantages: ..................................4 Connecting the scanner ............................5 Maintenance .................................. 5 Basic control codes ..............................6 Factory reset ................................... 6 Default custom settings ............................7 Scanner Backlight Settings ........................... 7 Crosshair settings ............................... -
Page 3: Specifications
Specifications: • Warranty: 2 years • Resolution: 1280 x 800 px • Sensor Type: CMOS • Scanning method: manual (on the button), automatically (after bringing the code closer) • Scan Acknowledgement: Light and Sound Signal • Interface: USB • Ingress protection: IP54 •... -
Page 4: Set Contents
Set contents: • Desktop QR & Barcode Scanner • USB cable Advantages: • Lightning-fast capture of leading 1D and 2D barcodes, including QR, DataMatrix • Effortlessly scan barcodes from LCD screens and mobile device displays • Possibility of automatic and manual scanning •... -
Page 5: Connecting The Scanner
Connecting the scanner Connect the scanner to the host device using a USB cable with RJ45 and USB connectors: 1. Plug the RJ45 connector into the slot on the scanner. 2. Plug the USB connector into the USB port of the host device. Maintenance •... -
Page 6: Basic Control Codes
• Do not use any detergents to clean other parts of the appliance, except water Note: The warranty does NOT cover damage caused by improper care and maintenance. Basic control codes Each time you want to configure the reader, you need to scan the Go to Setup Mode code, then read the barcode for the setting, and finally read the Exit Setup Mode code. -
Page 7: Default Custom Settings
Restore to factory settings Default custom settings Scanning the Restore All Custom Settings barcode allows you to reset all parameters to custom defaults. Scanning the Save as Custom Defaults barcode allows you to set the current settings as custom defaults. Default custom settings are stored in the scanner's memory. -
Page 8: Crosshair Settings
• Off: Backlight LEDs are off all the time • Fade: Backlight LEDs glow dimly in standby mode and gradually increase in brightness when scanning codes Normal (default) Always On Disabled Fade Crosshair settings When scanning, the reader displays a crosshair that allows the target barcode to be positioned in the field of view for easy decoding. -
Page 9: Light Signal Settings After Reading
Normal (default) Always On Disabled Light signal settings after reading The green barcode reading LED can be programmed to be on or off. Enabled (default) Disabled Setting the duration of the light signal It is possible to set the length of time for which the LED should remain on after the code has been read correctly. -
Page 10: Beep Settings When The Scanner Is Started
Short 20ms (default) 120 ms average Long 220ms Extended 320 ms Custom 1 – 2,500 ms Example of a custom LED duration setting for 800 ms: 1. Scan the Entry into Setup Mode barcode. 2. Scan the Custom barcode. 3. Scan the numeric barcodes "8", "0" and "0" from the "Digital Barcodes"... -
Page 11: Beep Settings After A Successful Read
Disabled Enabled (default) Beep settings after a successful read The scanner can be programmed to emit a beep after a successful read, or to turn off the beep. Enabled (default) Disabled Setting the beep duration after a successful read This parameter sets the length of the beep emitted by the scanner when it is read correctly. -
Page 12: Beep Frequency Setting
Long 120ms Custom Beep frequency setting This parameter can be programmed in 1 Hz increments from 20 Hz to 20,000 Hz. Ultra-low 800Hz Low 1600Hz Average 2730Hz (default) High 42000Hz Custom 20 – 20,000Hz... -
Page 13: Beep Volume Settings
Beep volume settings Loud (default) Medium Silent Barcode Scanning Mode Settings • Manual Mode: Pressing the trigger activates the decoding session. The decode session continues until the barcode is decoded or the trigger is released. • Auto mode: The scanner activates when a barcode is detected and scans it without the need to press the scan button. -
Page 14: Scan Sensitivity Setting
Continuous mode Scan sensitivity setting Sensitivity determines how responsive the scanner is to changes in ambient light. The higher the sensitivity, the less lighting is needed to start the scanner. You can choose the right degree of sensitivity that suits your environment. This feature is only available in automatic mode. -
Page 15: Letter Conversion Settings
Letter conversion settings No Conversion (Default) Conversion to uppercase Conversion to lowercase Prefix and Suffix Setting Prefix/ Suffix On Prefix/Suffix Disabled (Default) Custom prefix setting If a custom prefix is enabled, you can append a user-defined prefix to the barcode that cannot exceed 10 characters. For example, if the custom prefix is "AB"... -
Page 16: Set A Custom Suffix
Custom prefix disabled Custom prefix enabled (default) To set a custom prefix, you need to scan the Custom Prefix Setting barcode, followed by the numeric bar codes that correspond to the hexadecimal value of the desired prefix. After completing the above steps, you need to scan the Record Settings barcode. - Page 17 Custom Suffix Disabled Custom Suffix Enabled (Default) To set a custom suffix, scan the barcode setting the custom suffix, then the numeric barcodes corresponding to the hexadecimal value of the desired suffix, and finally read the Save Settings barcode. Note: A custom suffix cannot exceed 10 characters.
-
Page 18: Appendix 1. Numeric Barcodes
Appendix 1. Numeric barcodes... -
Page 20: Appendix 2. Save/Cancel
Appendix 2. Save/Cancel Saving settings Canceling settings...
Need help?
Do you have a question about the HD150 and is the answer not in the manual?
Questions and answers