Table of Contents
Advertisement
Demo/Dimmer function
All functions available on the system can be viewed on the
display and the display's brightness can be switched between
"on" and "off".
1
Press the Demo/Dimmer button.
Result: All functions available on the system appear on the front
panel display.
Each of these are explained in detail in this guide. Please refer to
the relevant section.
2
Press the Demo/Dimmer button again.
Result: The Dimmer function is selected and the display darkens.
Press the Demo/Dimmer button once again to brighten the front
panel display.
3
A display brightness control can only be performed while the
system power is on.
1,2
12
Setting the Clock
Your system is equipped with a clock which allows you to
turn your system on and off automatically. You should set the
clock:
When you first purchase the mini-compact system
After a power failure
After unplugging the unit
For each step, you have a few seconds to set the required
options. If you exceed this time, you must start again.
1
Switch the system on by pressing Standby/On.
2
Press Timer/Clock twice.
Result: CLOCK is displayed.
3
Press Enter.
Result: The hour flashes.
4
To...
Turn the Multi Jog knob to the...
Increase the hours
Right
Decrease the hours
Left
5
When the correct hour is displayed, press Enter.
Result: The minutes flash.
6
To...
Turn the Multi Jog knob to the...
Increase the minutes
Right
Decrease the minutes
Left
7
When the correct time is displayed, press Enter.
Result: The clock starts and is displayed, even when the system is in
standby mode.
You can display the time, even when you are using another
function, by pressing Timer/Clock once.
You can also use Program/Set button on the remote control
to instead Enter button in step 3, 5, 7.
You can also use
/
buttons to instead Multi Jog
knob in step 4, 6.
2
1
3,5,7
4,6
Loading and Changing Compact
Discs
The CD disc changer can contain up to three 12 cm or 8 cm
compact discs without using an adapter.
Never force the compact disc carrousel when opening and clos-
ing the compartment.
Never press down or place objects on the carrousel.
Always treat your compact discs with care; refer, if necessary, to
the section entitled "Precautions When Using Compact Discs" on
page 34.
1
Switch the system on by pressing On/Standby.
2
Press the Open/Close(
) button on the front panel.
Result: The compartment opens.
3
Place one or two discs in the front slots of the carrousel, with the
label on the discs facing upwards.
Check that the compact disc has been correctly inserted in
the holder before closing the compartment.
4
If you wish to load a third compact disc, press the Disc Change but-
ton on the front panel (or Disc Skip on the remote control).
Result: The carrousel rotates by 120°.
5
Close the compartment by pressing the Open/Close(
) button
again.
If you wish to start playing a disc directly, you can also
proceed as follows.
To play...
Press...
Disc 1
DVD/DVD-OK (
) or Disc 1
Disc 2
Disc 2
Disc 3
Disc 3
Result: The compartment closes automatically and the disc selected
starts playing.
6
To change or unload the compact disc changer, repeat Steps 2 to 5.
Keep the compartment closed whenever you are not using
it, to prevent dust from entering.
You can load or unload compact discs when the radio,
tape or auxiliary source function is selected.
2,5
5
4
5
1
Playing a Disc
Playback
1
Press the Open/Close(
) button.
2
Place a disc gently into the tray with the disc's label facing up.
3
Press the Play/Pause(
) button or Open/Close(
) button to
close the disc tray.
Pausing Playback
Press the Play/Pause (
) button during playback.
To resume, press the Play/Pause (
) button again.
Depending on the disc, the initial disc information screen may
look disc to disc.
When playing a DVD containing MPEG format, video may not
be reproduced correctly and you may get picture distortion.
Stopping Playback
Press the Stop (
) button during playback.
During playback, when the Stop (
)button is pressed, the position is stored
in the memory, and
STOP is shown on the display.
When the Play/Pause (
) button or Return button is pressed
subsequently , playback resumes from the position at which it was stopped.
If the Stop (
) button is pressed a second time, the resume play' memory
function is canceled, and
STOP is shown on the display. When the
Play/Pause (
)button is pressed, playback starts from the beginning.
1,3
3
Selecting a Disc in the CD changer
The CD function is automatically selected when DISC SKIP is
pushed.
To select a specific disc, press the corresponding Disc (1, 2, 3) button
on the front panel or Disc Skip on the remote control, until the
required disc indicator flashes.
If you use the Disc (1, 2, 3) function when listening to the
radio or to a tape, the system switches automatically to the
DVD/CD mode.
If the disc selected is not loaded, the next disc is played auto-
matically.
GB
13
Advertisement
Table of Contents
