When operates and maintains an ice maker ,be sure to pay attention to the safety tips in the Service & Installation Manual manual. Ignoring these tips may result in personal injury and ice maker damage. Safety Warnings ICE MACHINES In this manual, you will see the following forms of security tips: 安全提示...
Service & Installation Manual 安全提示 Features, Size & Apprearance Features ICE MACHINES 1. Features ice maker has a number of patented Appearance control systems, simple operation and precise control, suitable for different water quality conditions; The key components are from international renowned brands, which ensures reliability in harsh environments;...
Service & Installation Manual 安 Unpacking, Installation & Water Supply 制冰机工作流程制冰机共组哟流程制冰工作流程制冰机 Unpacking ICE MACHINES 全提示 empty the ice maker when the temperature is 3. Unpacking below zero(see “preparation for long-term storage of ice maker”) Before unpacking, check the anti-tilt sign is in ...
Service & Installation Manual 安 制冰机工作流程制冰机共组哟流程制冰工作流程制冰机 Drainage, Power, Cleaning & Check Drainage ICE MACHINES 全提示 6.2 Drainage 8. Clean after Installation When installing drain hose, follow these After the ice maker is installed, clean the shell, guidelines to be sure all purged water flowing liner and ice scoop with a clean wet cloth or into gully drain:...
Service & Installation Manual Operation 安全提示 ICE MACHINES Operation In the ice making state, click "[Reservation/Add]" or 10. Operation "[Light/Subtract]" to see the "Temperature Display" number on the screen start to flash, press "[Reservation/Add]" once to add 1 10.1 Turn on/off minute, Press twice to increase by 2 minutes, and so on, in Turn on :...
Service & Installation Manual 安全提示 Ice Making Workflow Operation ICE MACHINES valve are all closed. If the ice is taken away, the ice full indicator light will flash within 180 seconds when the ice In the standby state (the screen displays OFF), press and is full, and after the ice is full 180 seconds, it will switch to power on and start a new cycle.
Service & Installation Manual 安全提示 Routine Cleaning Cleaning and Disinfection ICE MACHINES a clean soft cloth. Stainless steel cleaner can be used when necessary. ★Important Air filter cleaning: The filter can filter out dirt or dust If cleaning of some parts is necessary, it is in the air and prevent the condenser from clogging.
Service & Installation Manual 安全提示 Routine Cleaning & Disinfection Cleaning and Disinfection ICE MACHINES to scrub inside the sink Click the button to be in the standby state, the screen displays "OFF", unplug the power plug, use a screwdriver to remove the two screws on the water pump box, and then loosen the 3 screws on the inner wall of the ice-hanging plate, remove the clamp, pull out The connectors at the lower and upper water pipes,...
Service & Installation Manual 安全提示 Cleaning Process Cleaning and Disinfection ICE MACHINES The water from the sink to the evaporator has been 14.1 Cleaning process circulated for cleaning. After about 15 minutes, the cleaning stops and starts to 1. Open the front panel of the ice maker and check if the ice maker evaporator is making ice.
Service & Installation Manual 安全提示 Cleaning & Disinfection Cleaning and Disinfection ICE MACHINES Scrub ice storage bin After soaking, put on rubber gloves and carefully Brush flow pipe mandrel clean all parts with a soft nylon brush, sponge or soft cloth While soaking the parts, use a nylon brush or a soft cloth dipped in cleaning fluid to wipe the surfaces...
Service & Installation Manual 安全提示 Disinfection Process Cleaning and Disinfection ICE MACHINES After 20 minutes, take out the soaked parts and rinse the sterilized parts with clean water. Install the removed parts back in place((Refer to 15.3 Parts removal/installation process for installation method) Strictly click and perform this step as required.
Service & Installation Manual 安全提示 Disinfection Process Cleaning and Disinfection ICE MACHINES b. Remove the two screws Enter the automatic rinsing phase, first clean for 3 minutes, then drain for 30 seconds, after the tap water rinsing process cycle 2 times, and then rinse with pure water 3 times, the entire cleaning process ends, the screen displays "OFF", about 37 minutes later the entire cleaning process After the end, the...
Service & Installation Manual 安全提示 Removal From Service / Winterization Cleaning and Disinfection ICE MACHINES 安全提示 Removal from service / Winterization 15.Removal from service / Winterization Special protection measures are required if the ice maker is out of service for a long period of time or exposed to an environment of 0°C or less.
Service & Installation Manual !Warning Warnings Danger-There is a risk of fire or explosion. The refrigerant is a flammable refrigerant. ICE MACHINES Only trained service personnel can carry out repair work. Do not damage the refrigeration piping. !Warning Danger-There is a risk of fire or explosion. The refrigerant is a flammable refrigerant. Please read the service manual before using this product.
connected, the fuse is not burnt out and whether the plug is fixed well. Service & Installation Manual c). Whether the ambient temperature is too high or too low (the operating temperature range ice maker is 10°C~38°C), whether the water temperature is too high or too low (the water temperat Circuit Diagram ICE MACHINES range is 5°C~32°C).
Service & Installation Manual 安全提示 Structural Explosive View Explosive view ICE MACHINES 18.Explosive view Stuctural Explosive view Serial Figure Serial Figure Top cover plate Before the beam Rack triangle block stents Hanging ice plate After the bar (small) Condenser top ABS board cover plate Right side vertical...
Need help?
Do you have a question about the MCF and is the answer not in the manual?
Questions and answers