Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for MechMaxx D50MA
Summary of Contents for MechMaxx D50MA
- Page 1 WARRANTY Operator’s Manual www. mechmaxx.com...
-
Page 3: Table Of Contents
REPLACING TRACKS FUEL SAFETY ENGINE MAINTENANCE SPECIFIC SAFETY RULES STORAGE UNPACHING THE CONTAINER TROUBLESHOOTING CONTENTS SUPPLIED KNOW YOUR MACHINE OPERATION ADD OIL TO ENGINE ADD GASOLINE TO ENGINE STARTING ENGINE OPERATING IDLE SPEED STOP ENGINE www. mechmaxx.com TABLE OF CONTENTS... -
Page 4: Specifications
SPECIFICATIONS Model D50MA Engine Rato Engine Type Single cylinder,4 stroke, air-cooled,OHV Engine Displacement 212cc Horsepower Power 4.1kw/3600rpm Transmission Transaxle 3 forward/1 reverse speed Working Pressure 16.5Mpa Driven Type Track Track Roller 4 pcs Track Tensioning Bucket Capacity 1100 lbs Box Size 38*27*19 in www. -
Page 5: Safety Signs
Gear oil GL-5 or GL-6, SAE80W-90 is recommended. Do not use synthetic oil. STOP WARNING:OPERATE THE STEERING LEVERS ONLY AT A REDUCED SPEED OPERATE THE STEERING LEVERS ONLY AT A LOW SPEED. www. mechmaxx.com SAFETY SIGNS... -
Page 6: Safety
Always keep hands and feet away from all moving parts equipped with a spark arrester meeting applicable local, during operation. Moving parts can cut or crush body state, or federal laws. parts. www. mechmaxx.com SAFETY... -
Page 7: Fuel Safety
Instead, move gravel drives, walks, or roads. Stay alert for hidden the machine away from the area of spillage and avoid hazards or traffic. creating any source of ignition until fuel vapors have dissi- pated. www. mechmaxx.com SAFETY... - Page 8 When dumping the contents of the hopper, the center of gravity will change continuously and the ground condi- tions will be essential for the stability of the machine. Use extra caution and control when dumping the hopper on unstable ground, such as wet clay or soil. www. mechmaxx.com SAFETY...
-
Page 9: Unpaching The Container
UNPACHING THE CONTAINER Use the screwdriver and hammer to open all the side locks. www. mechmaxx.com UNPACHING THE CONTAINER... -
Page 10: Contents Supplied
The mini tracked dumper comes partially assembled and is shipped in carefully packed package. After all the parts have been removed from the package, you should have: WARRANTY Operator’s Manual www. mechmaxx.com 1.Machine 3. Tools for Spark Plug Assembly 2.Operator's Manual & Engine Manual www. -
Page 11: Know Your Machine
KNOW YOUR MACHINE Throttle Control Engine Switch Right Steering Lever Clutch Control Lever Left Steering Lever Dump Box Gear Selection Lever Tipping Handle Gearbox Gas Spring Assistance Track www. mechmaxx.com KNOW YOUR MACHINE... - Page 12 If the front continues to ride up, lift up on the moves between FAST SLOW and STOP positions. handles. LEFT/RIGHT STEERING LEVER The throttle control will shut off the engine when it is moved to the STOP position. Operate the lever to turn left/right. www. mechmaxx.com KNOW YOUR MACHINE...
-
Page 13: Choke Control
The choke control slides between the CHOKE CLOSED and CHOKE OPEN posi- tions. Never use choke to stop engine. CLUTCH CONTROL LEVER Squeeze the control lever, clutch engaged. Release the lever, clutch disengaged. www. mechmaxx.com KNOW YOUR MACHINE... -
Page 14: Operation
1. The engine must be off and allowed to cool at least two minutes before adding fuel. 2. Remove the fuel filler cap and fill the tank. (See engine manual for fuel capacity, fuel recommendation, and location of fuel cap.) www. mechmaxx.com OPERATION... -
Page 15: Operating
When the machine is fully loaded, more pressure is required. The power trackbarrow has a maximum capacity of 660 LBS. However, it is advisable to assess the load and adjust it according to the ground on which the machine will be used. www. mechmaxx.com OPERATION... -
Page 16: Maintenance
10mm wrench until you have reached your required tightness. 3. Once tightness is set, return the jam nut against the Adjustment Nut handle to hold the cable in place. Jam Nut www. mechmaxx.com MAINTENANCE... -
Page 17: Replacing Drive Belt
If you remove the oil level plug and no oil flows out, please add oil and then screw the oil level plug. M6×20 Gear oil GL-5 or GL-6, SAE80W-90 is recommended. Do not use synthetic oil. Belt Cover for Gearbox Pulley www. mechmaxx.com MAINTENANCE... -
Page 18: Tightening Tracks
3. Measure the track midline vs. the horizontal line. The reading must not be more than 10cm-15cm Steering Wheel Axle Do not over-tighten your track. The adjustment of the track and the brakes are linked. The braking power will lessen the more the track is tightened. www. mechmaxx.com MAINTENANCE... -
Page 19: Replacing Tracks
3. Remove the three M8×16 bolts and washers that fix 6. Remove the M10×60 bolt, washers and nut from the the track protection guard. driving wheel. 7. Pull out the whole track with driving wheel. M8 × 16 www. mechmaxx.com MAINTENANCE... -
Page 20: Engine Maintenance
ENGINE MAINTENANCE Refer to the Engine Manual included in your unit for the information on engine maintenance. Your engine manual provides detailed information and a maintenance sched- ule for performing the tasks. www. mechmaxx.com MAINTENANCE... -
Page 21: Storage
6. Store your unit on flat ground in a clean, dry building that has good ventilation. Do not store the machine with fuel in a non-ventilated area where fuel fumes may reach flame, sparks, pilot lights or any ignition sources. www. mechmaxx.com STORAGE... -
Page 22: Troubleshooting
2. Drive belt not tight enough. different gears. while engine is running 2. Tighten drive belt. Remove the foreign body. Foreign bodies have worked their One of the two tracks is way between the track and the blocked. frame. www. mechmaxx.com TROUBLESHOOTING... - Page 24 info@mechmaxx.com...
Need help?
Do you have a question about the D50MA and is the answer not in the manual?
Questions and answers