Advertisement
Enware Wellbeing
Faced Toilet Suite - Standard Height
Installation and Maintenance Instructions
WB-WCCCBTW-SH
technical data
Working Pressure Range
Inlet Connection
Water Inlet Connection Method
Outlet Connection
Enware products are to be installed in accordance with the Plumbing Code of Australia (PCA) and AS/NZS3500.
Installations not complying with PCA and AS/NZS 3500 may void the product and performance warranty provisions.
Reference should also be made to the Australasian Health Facility Guidelines (AHFG), ABCB and Local Government
regulations when considering the choice of, and the installation of these products.
This product must be installed and commissioned by a qualified plumber.
For use with potable water only.
NOTE: Enware Australia advises:
1. Due to ongoing Research and Development, specifications may change without notice.
2. Component specifications may change on some export models.
I00623_14 May 2024
1300 369 273 | info@enware.com.au | enware.com.au
Close Coupled Wall
®
Min 50 kPa
Max 500 kPa
1/2" BSP (DN15)
Back inlet or bottom inlet (on either side of pan)
DN100 DWV PVC Pipe (S-Trap Adaptor) / DN100 DWV PVC Pan Collar (P-Trap)
Advertisement
Table of Contents
Related Manuals for Watts Enware Wellbeing WB-WCCCBTW-SH
Summary of Contents for Watts Enware Wellbeing WB-WCCCBTW-SH
- Page 1 Enware Wellbeing Close Coupled Wall ® Faced Toilet Suite - Standard Height Installation and Maintenance Instructions WB-WCCCBTW-SH technical data Working Pressure Range Min 50 kPa Max 500 kPa Inlet Connection 1/2” BSP (DN15) Water Inlet Connection Method Back inlet or bottom inlet (on either side of pan) DN100 DWV PVC Pipe (S-Trap Adaptor) / DN100 DWV PVC Pan Collar (P-Trap) Outlet Connection Enware products are to be installed in accordance with the Plumbing Code of Australia (PCA) and AS/NZS3500.
-
Page 2: Installation
installation Determine location and set out for the toilet. Prepare water and waste outlet points according to the setout dimensions shown below. 620 +/-7 620 +/-7 REAR ENTRY 95+/-5 WATER INLET POINT BOTTOM ENTRY OPTION WATER INLET POINT ON EITHER SIDE OF PAN MIN 75 MAX 140 460 +/-5... - Page 3 ROUGH-IN 1. Determine Set Out For The Toilet Pan S-Trap Set-Out: Min 75mm – max 140mm from finished wall. The outlet pipe should be DN100 PVC DWV pipe. The S-Trap Adaptor has a rubber seal that inserts inside the DN100mm pipe. P-Trap Set-Out: P-Trap spigot is 185 +/-5mm from base of pan.
- Page 4 Fit the rubber seal around the tail of outlet valve located at the bottom of cistern. SEE IMAGE 02 Rubber seal (For bottom inlet: Connect inlet hose to the inlet connection on the bottom of cistern, and feed the hose through the hole located on the side of pan.) Lift the cistern into position and lower onto the (Inlet hose -...
- Page 5 5. Fix Pan Onto Floor Determine floor fixing requirements. Ensure the floor mounting bracket screws can be fixed onto floor material with adequate structural integrity and strength. Position pan in place, and mark anchor holes for floor mounting brackets. Remove pan, pre-drill anchor holes where marked, and install fixing brackets.
- Page 6 7. Caulking Adjust the position of the toilet pan so it sits level. Ensure the floor surface is clean and dry - free of dust, moisture and grease. Lift pan slightly to apply silicone sealant to the bottom contact surface of the pan and around the perimeter of the foot of the pan, to create a thorough seal between the pan and floor.
- Page 7 8. Install Toilet Seat Toilet seat has a top-fixing hinge that does not require access from underneath the pan. Insert top fixing rawl plugs into the seat bolt holes of the pan. Place the hinge blocks, without the stainless steel covers, over the rawl plugs and loosely fix the screw through the hinge blocks into the rawl plugs.
- Page 8 9. Install Flush Button The bridge piece on the outlet valve has been lowered for packing and transport. Adjust to position number “4”. SEE IMAGE 11 Place push button case through the cistern lid hole. Lower the cistern lid onto the cistern while ensuring the actuator holes are aligned with the push button case.
-
Page 9: Maintenance
maintenance CLEANING • WC units have a glazed surface. Glazed surfaces are easy to keep clean and are resistant against most chemicals. • Clean bowl regularly. • Clean external surfaces regularly with a dry, soft cloth or a sponge. Alternatively clean with a soft damp cloth using only mild liquid detergent or soap and water, and wipe dry with a cloth. -
Page 10: Troubleshooting
troubleshooting PROBLEM CAUSE RECTIFICATION Toilet not flushing away Flush volume too low Increase flush volume Offset pan collars are used Do not use offset pan collars Drain blockages that can impede outlet flow Water constantly runs Cistern fill level is too high Adjust fill level on inlet valve into bowl to lower the water level... -
Page 11: Product Warranty Statement
- WATTS AUSTRALIA EFFECTIVE FROM 20 November 2023 3. Our responsibilities This Warranty Statement applies to products supplied by Australian Valve (a) In the event that the Supplier is reasonably satisfied that there is a Group Pty Ltd (ACN 068 227 270) (AVG) or Enware Pty Ltd (ACN 662... - Page 12 1300 369 273 info@enware.com.au enware.com.au...
Need help?
Do you have a question about the Enware Wellbeing WB-WCCCBTW-SH and is the answer not in the manual?
Questions and answers