VEVOR 3402 Manual
  1. Manuals
  2. Brands
  3. VEVOR Manuals
  4. Welding System
  5. 3402
  6. Manual
VEVOR 3402 Manual

VEVOR 3402 Manual

Stud welder dent repair kit
Hide thumbs

Advertisement

Table of Contents

Technical Support and E-Warranty Certificate www.vevor.com/support
STUD WELDER DENT REPAIR KIT
MODEL:3402
We continue to be committed to provide you tools with competitive price.
"Save Half", "Half Price" or any other similar expressions used by us only represents an
estimate of savings you might benefit from buying certain tools with us compared to the major
top brands and does not necessarily mean to cover all categories of tools offered by us. You
are kindly reminded to verify carefully when you are placing an order with us if you are
actually saving half in comparison with the top major brands.

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the 3402 and is the answer not in the manual?

Questions and answers

Subscribe to Our Youtube Channel

Related Manuals for VEVOR 3402

Summary of Contents for VEVOR 3402

  • Page 1 Technical Support and E-Warranty Certificate www.vevor.com/support STUD WELDER DENT REPAIR KIT MODEL:3402 We continue to be committed to provide you tools with competitive price. "Save Half", "Half Price" or any other similar expressions used by us only represents an estimate of savings you might benefit from buying certain tools with us compared to the major top brands and does not necessarily mean to cover all categories of tools offered by us.

  • Page 2: Safety Warning Signs

    STUD WELDER DENT REPAIR KIT Safety Warning Signs Operate this protection with working conditions common sense Before installing and operating the welder, look at the following safety precautions To prevent electric shock: 1.Do not use the skin Read the instructions 1. before the and wet clothes contact welding machine.

  • Page 3: Specifications And Parameters

    Installation 1.Specifications and parameters Model 3402 Input voltage（V） AC200-240V Output voltage（V） AC1-7V Input power（KW） Instantaneous maximum output current（A） 3500A Input the maximum current（A） Way of working Automatic/manually Regular working hours Automatic mode Work stalls One-button mode 5 types (Triangular pieces, round gaskets, long gaskets, wavy lines, hot pressing flat) Welding thickness（mm）...
  • Page 4 2.The work cycle and overheating protection The working cycle of the machine is the use of repeated cycle of work, the welding cycle time for the load time and no load time and. In addition, the machine is equipped with overheating protection, when the temperature reaches the critical, the welding machine will automatically stop working, to be cooled, you can continue to operate, as shown in the specific situation.
  • Page 5 4.Move and place the machine's attention 1).After the installation of the machine if no other problems, we must choose the right place to put. 2).The length of the input power cord is determined according to the operating distance, and the power cord must not be less than 4 mm copper cable. 3).When placed in the machine, can not be tilted around, to be stable on the ground to avoid damage to the machine.
  • Page 6 1.Operation panel guidelines 1..Display 2.Overheat protection indicator 3.Tools and Time Adjustment 4.ON/OFF 5.Torch wire 6.Signal line 7.Ground wire Note: Machine overload work will enter the protection state, until the machine cooling, and then work...

  • Page 7: Connection Of Negative Wire

    2.Welding torch and connector 1.Locking head 2.Torch switch Application of single - sided spot welding gun Carbo Rod Shrinking OT Washer Welding Washer Welding Hot pressing Wave form Wire Welding Pulling Spot Hammer Connection of negative wire 1.Place the wire on the 2.the welding torch in the vicinity of 3.Fixed ground sheet metal section that...
  • Page 8 3.Method of operation a.Gasket welding The negative line fixed to Connect the gasket Point the spin button to the polished clean and connector to the torch and the corresponding tool remove the paint on the lock it with a gasket. range.
  • Page 9 b.Triangular pieces of weldin The negative line fixed to the Connect the connected Point the spin button to polished clean and remove the the corresponding tool triangular pull hammer paint on the workpiece, the closer range. to the torch and lock it. the operating surface the better .
  • Page 10 c. carbon rod heating The negative line fixed to the Connect the connected Point the spin button to polished clean and remove the the corresponding tool triangular pull hammer paint on the workpiece, the closer range. to the torch and lock it. the operating surface the better .
  • Page 11 d.wave line welding The negative line fixed to the Connect the connected Point the spin button to polished clean and remove the the corresponding tool triangular pull hammer paint on the workpiece, the closer range. to the torch and lock it. the operating surface the better .

  • Page 12: Maintenance And Repair

    e.The use of sucker Use of manual sucker: 1. the sucker and pull hammer connected 2. the sucker forced to no dead angle of the depression 3.with the hammer in the opposite direction to pull out the depression Maintenance and repair Failure and exclusion Trouble Reason...

  • Page 13: Packing List

    Packing List Part name Quantity Remarks Mainframe Tool Box Pulling Hammer Pulling gun Wavy wire meson head Carbon Rod Head Spot Welding Head Carbon Rods Wrench Pull Hook Six-jawed Hook Triangle Tabs Long shims (OT) Round Spacer Suction Cups...
  • Page 14 Technical Support and E-Warranty Certificate www.vevor.com/support...

Table of Contents