Ryobi RB1815C Original Instructions

Important!
It is essential that you read the instructions in
this manual before assembling, operating, and
maintaining the product.
Subject to technical modifications.
Save all warnings and instructions for future reference.
The term "power tool" in the warnings refers to your mains-operated
(corded) power tool or battery operated (cordless) power tool.
SAFETY INSTRUCTIONS
WARNING
To reduce the risk of fire, personal injury, and product damage due
to a short circuit, never immerse your tool, battery pack or charger
in fluid or allow a fluid to flow inside them. Corrosive or conductive
fluids, such as seawater, certain industrial chemicals, and bleach or
bleach-containing products, etc., can cause a short circuit.
The product is not intended for use by persons (including children) with
reduced physical, sensory or mental capabilities, or lack of experience
and knowledge, unless they have been given supervision or instruction
concerning use of the product by a person responsible for their safety.
Children should be supervised to ensure that they do not play with the
product.
Please read and observe these instructions before using the product.
■ When battery pack is not in use, keep it away from other metal
objects such as paper clips, coins, keys, nails, screws or other
small metal objects that can make a connection from one terminal to
another. Shorting the battery terminals together may cause sparks,
burns or fire.
■ Do not place battery tools or their batteries near fire or heat. This will
reduce the risk of explosion and possible injury.
■ Do not crush, drop or damage battery pack. Do not use a battery
pack or charger that has been dropped or received a sharp blow.
A damaged battery is subject to explosion. Properly dispose of a
dropped or damaged battery immediately.
■ Batteries can explode in the presence of a source of ignition,
such as a pilot light. To reduce the risk of serious personal injury,
never use any cordless product in the presence of open flame. An
exploded battery can propel debris and chemicals. If exposed, flush
with water immediately.
■ Do not charge battery tool in a damp or wet location. Following this
rule will reduce the risk of electric shock.
■ For best results, charge the battery tool in a location where the
temperature is more than 10°C but less than 37°C. To reduce the
risk of serious personal injury, do not store outside or in vehicles.
■ Under extreme usage or temperature conditions, battery leakage
may occur. If liquid comes in contact with the skin, wash immediately
with soap and water, then neutralize with lemon juice or vinegar. If
liquid gets into the eyes, flush them with clean water for at least 10
minutes, then seek immediate medical attention. Following this rule
will reduce the risk of serious personal injury.
TRANSPORTING LITHIUM BATTERIES
Transport the battery in accordance with local and national provisions
and regulations.
Follow all special requirements on packaging and labelling when
transporting batteries by a third party. Ensure that no batteries can
come in contact with other batteries or conductive materials while
in transport by protecting exposed connectors with insulating, non-
conductive caps or tape. Do not transport batteries that are cracked or
leaking. Check with the forwarding company for further advice.
ORIGINAL INSTRUCTIONS
18V LITHIUM-ION BATTERY PACK
RB1815C / RB1820C / RB1825C / RB1840C / RB1850C / RB1840X /
RB1850X / RB1860X / RB18L90A / RB1880T / RB18120T
Even when the product is used as prescribed, it is still impossible to
completely eliminate certain residual risk factors. The following hazards
may arise and the operator should pay special attention to avoid the
following:
■
■
Use the battery pack for Ryobi One+ 18V cordless products only.
Battery protection features
Ryobi One+ 18V lithium-ion battery packs are designed with features
that monitor and protect the lithium-ion cells (active, standby, shut off
and sleep modes ) and maximize battery life.
■
■
■
NOTE: A completely discharged battery (sleep mode) needs
reactivation before the charging process begins. To reactivate a battery
in sleep mode, place the battery in the charger and wait for 90 seconds.
If the charging process does not begin, please remove the battery and
wait for 30 seconds. Then start a second attempt to re-activate the
battery by placing it in the charger. If the charging process does not
begin after 3 attempts, the battery may be faulty. In this case, have
the battery serviced by a qualified repair person using only identical
replacement parts.
NOTE: The LED charge indicator light will not work if the battery
protection feature has caused the battery pack to stop powering the
tool (sleep mode). When the charger resets the battery pack, the LED
will again function.
■
Cold weather operation
The lithium-ion battery pack can be used in temperatures down to
-10°C. Put the battery pack on a tool and use the tool in light duty
application. After a while, the battery pack will warm up and begin
operating normally.
Charging the battery pack
Battery packs are shipped in a low charge condition to prevent possible
problems. Therefore, they should be charged prior to first use.
NOTE: If the charger does not charge the battery pack under normal
circumstances, return both the battery pack and charger to the nearest
Ryobi authorised service centre for electrical check.
RESIDUAL RISKS
Use the product only for its intended use. Do not alter or modify the
product from the original design or function.
Always be aware that misuse and improper handling of the product
can cause injury to yourself and others.
INTENDED USE
OPERATION
The tool may stop during use to prevent overheating or overloading
of the battery (active mode). In this case, release the trigger to reset
and resume operation.
If this does not reactivate the tool, the battery is completely
discharged (stand-by or sleep mode) and needs to be charged in
a compatible charger.
The battery can be recharged in stand-by or sleep mode. It is
not necessary to completely discharge the battery pack before
recharging.
The One+ 18V lithium-ion battery packs are equipped with an
additional SHUT-OFF mode, minimizing self-discharge of the battery
while the battery is not in use. It will be reactivated automatically
when used with a tool or by pressing the LED gauge.
NOTE: In SHUT-OFF mode, the battery will show low voltage
when tested with a volt-meter. Use the battery in a tool or press
the LED gauge for read-out of the actual voltage.