Samsung LA32C450E1M User Manual page 17

Basic Features
Size : Your cable box/satellite receiver
■
may have its own set of screen sizes as
well. However, we highly recommend
you use 16:9 mode most of the time.
Auto Wide: Automatically adjusts the
picture size to the 16:9 aspect ratio.
✎
This feature is only available in New Zealand,
Singapore.
16:9 : Adjusts the picture size to 16:9 for DVDs or wide S.MODE
broadcasting.
Wide Zoom: Magnifies the picture size more than 4:3.
✎
Adjusts the Position by using
Zoom: Magnifies the 16:9 wide pictures vertically to fit
the screen size.
✎
Adjusts the Position or Size by using
4:3 : The default setting for a movie or normal
broadcasting.
✎
Do not watch in 4:3 format for a long time. Traces
of borders displayed on the left, right and centre
of the screen may cause image retention(screen
burn) which are not covered by the warranty.
Screen Fit: Displays the full image without any cut-off
when HDMI (720p / 1080i / 1080p) or Component
MEDIA.P
(1080i / 1080p) signals are inputted.
✎
NOTE
x
After selecting Screen Fit in HDMI (720p / 1080i /
1080p) or Component (1080i / 1080p) mode, you
may need to center the picture:
1. Press the ◄ or ► button to select Position.
2. Press the ENTERE button.
3. Press the ▲, ▼, ◄ or ► button to move the
picture.
x
Depending on the input source, the picture size
options may vary.
x
The available items may differ depending on the
selected mode.
x
In PC mode, only 16:9 and 4:3 modes can be
adjusted.
x
Settings can be adjusted and stored for each
external device connected to an input of the TV.
x
If you use the Screen Fit function with HDMI 720p
input, 1 line will be cut at the top, bottom, left and
right as in the overscan function.
16
English
P.SIZE
HDMI
▲, ▼ buttons.
▲, ▼ button.
GUIDE
Screen Mode (16:9 / Wide Zoom / Zoom / 4:3)
■
Available only when picture size is set to Auto Wide. You
can determine the desired picture size at the 4:3 WSS
(Wide Screen Service) size or the original size. Each
European country requires different picture size.
✎
This feature is only available in New Zealand,
Singapore.
✎
Not available in PC, Component or HDMI mode.
Digital Noise Filter (Off / Low / Medium / High / Auto
■
/ Auto Visualisation): When the broadcast signal is
weak, some static and ghosting may appear. Select one
of the options until the best picture is displayed.
Auto Visualisation: When changing analogue channels,
displays the intensity of the current signal and defines
the screen noise filter.
✎
Only available for analogue channels.
MPEG Noise Filter (Off / Low / Medium / High /
■
Auto): Reduces MPEG noise to provide an improved
picture quality.
✎
Disabled under PC mode.
HDMI Black Level (Normal / Low)
■
level on the screen to adjust the screen depth.
✎
Available only in HDMI mode (RGB signals).
Film Mode (Off / Auto1 / Auto2)
■
automatically sense and process film signals from all
sources and adjust the picture for optimum quality.
✎
Available in Digital TV for resolution 576i & 1080i
and All Analogue TV, AV, COMPONENT (480i /
1080i) and HDMI (480i / 1080i).
Auto Protection Time (2 hours / 4 hours / 8 hours
■
/ 10 hours / Off) : If the same image remains on the
screen, Auto Screen Burn Protector will work.
Picture Reset (OK / Cancel)
Resets your current picture mode to its default settings.
Setting up the TV with Your PC
¦
Set the input source to PC.
Auto Adjustment
Adjust frequency values/positions and fine tune the settings
automatically.
✎
Not available when connecting through HDMI/DVI
cable.
Screen
Coarse / Fine : Removes or reduces picture noise. If the
■
noise is not removed by Fine-tuning alone, then adjust
the frequency as best as possible (Coarse) and Fine-
tune again. After the noise has been reduced, readjust
the picture so that it is aligned to the centre of screen.
Position : Adjust the PC screen position with direction
■
button (▲ / ▼ / ◄ / ►).
Image Reset : Resets the image to default settings.
■
: Selects the black
: Sets the TV to
t
: